Question about Jeep Cherokee

1 Answer

How do I repair oil cooling system on a jeep 1993

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 242 Answers

If it's leaking, you can try some STP oil stop leak. If it's leaking from tranny cooler in front, quick fix is just some RTV/ JB Weld epoxy. It all depends on where you are leaking from.

Posted on Sep 17, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is the oil tempature high


if it is the sump oil temp then there is too much compression blow by getting into the sump. If it is a transmission oil temp then that indicates over loading of the transmission ( too fast or trailer too heavy) of slipping of clutches and bands ( out of adjustment) or excessive oil level ( frothing and aeration of the oil) or the radiator temperature is too high to allow cooling of the transmission oil

Apr 30, 2014 | 1993 Jeep Grand Cherokee

1 Answer

1993 jeep grand cherokee havc code 06


Chrysler & Jeep Cooling System & HVAC Service: Every car make has its quirks, and Chrysler and Jeep vehicles are no exception. In researching this article, we found several examples of heater problems in these vehicles that seem to be fairly common.

On 2001 and 2002 Sebring Sedan, Sebring Convertible and Stratus Sedan, plus 1993 to 2002 Chrysler Concorde, LHS, New Yorker and 300M, Eagle Vision and Dodge Intrepid models with V6 engines, customers may complain their engine is overheating, or the heater is putting out little or no heat.

Chrysler Technical Service Bulletin 07-002-02 says the problem can be caused by a low coolant level in the cooling system. On these vehicles, air trapped inside the cooling system can displace coolant when the system is refilled. The radiator and coolant reservoir may appear to be full, but there still may be air inside the heater core and heater hoses. This will create a low coolant level that may lead to overheating and low heater output. The bulletin provides a special fill procedure to eliminate the trapped air so the cooling system can be completely filled.

The procedure goes as follows:
1. Obtain Chrysler special tool 8195 (Cooling System Filling Aid). The tool looks like a funnel and attaches onto the filler neck (just as a regular pressure cap does). But it also has a hose clip.
2. Attach the filling aid tool to the cooling system filler neck. Use the clip to pinch off the overflow hose attached to the fill neck. Attach a 4-6' long 1/4" ID clear hose to the bleed valve. Put the end of the hose into a clean container (to prevent coolant from spilling onto the accessory drive belts).
3. Open the cooling system air bleed valve before any coolant is added. If you do not do this, air can remain trapped inside the system and you won't get all the air out. On 1998 and later models with 2.7L engine, the valve is located on the water outlet connector at the front of the engine. On 3.2L and 3.5L engines, the valve is located on the lower intake manifold, left of center under the upper intake manifold. On 1993-'97 models with 3.3L and 3.5L engines, the valve is on the thermostat housing.
4. Pour a 50/50 mixture of coolant and water into the large side of the filling aid funnel. Use distilled, deionized or reverse-osmosis purified water, not ordinary tap water, which may contain salt or minerals that could contaminate the coolant.
5. Slowly fill the cooling system through the large side of the filling aid. Watch the hose connected to the bleed valve. When a steady stream of coolant comes out of the hose, close the bleed valve and continue filling to the top of the filling aid.
6. On 1993-'97 models, place a small, clean container below the end of the overflow hose. Then remove the clip from the overflow hose. Any excess coolant in the filling aid will now drain into the overflow section of the coolant bottle or into the container.
7. On 1993-'97 models, remove the reservoir and recycle the excess coolant.
8. Remove the filling aid from the fill neck. Make sure the filler neck and cap are clean, then replace the pressure cap on the coolant bottle.

Note: 1998 and later coolant bottles have two chambers. Coolant will normally only be in the inboard (smaller) of the two. The outboard chamber is only to recover coolant in the event of an overheat and should normally be empty - except for the coolant drained from the filling aid. This coolant will be drawn back into the pressurized side of the cooling system over time.

Hope helps.

Jan 12, 2011 | 1993 Jeep Grand Cherokee

1 Answer

COOLING CAPACITY FOR 1993 TAURUS


1993 FORD TAURUS 3.0L 6-cyl Engine Code [Y] SHO
Engine oil, with filter..........4.7 liters
Cooling System, Initial Fill..........11 liters


Good luck and hope this helps, thank you for using fixya

Nov 04, 2010 | 1993 Ford Taurus

1 Answer

My car has oil in the anti-greeze / radiator. There is NO water/anti-freeze in the oil. What problems will this create?


I presume that you mean oil in the cooling system. there is a leak somewhere and needs to be attended to right away.

Oil in cooling system will deteriorate the hoses...

Oil pressure is often more than cooling system pressure, which is why coolant not in the oil.

Guessing that there is a head gasket leak.....

May 24, 2010 | 1993 Ford Mustang

1 Answer

I CHANGED MY SPARK PLUGS ON MY 1993 BIGHORN ISUZU PETROL, ONE OF MY SPARKS WAS COVERED IN OIL, CAN YOU TELL WHAT COULD BE CAUSING THIS?


ad piston rings may be the cause of oil on the spark plug. what happens under normal operation the oil that lubricates and cools the cylinder walls is getting on the other side of the piston, where the spark plug is and covering it in oil. A good test for this is a compression tester, this will tell you if it in fact is piston rings.

Apr 27, 2010 | 1993 Jeep Grand Cherokee

1 Answer

I have a oil leak.


hope its not rear main but for that age car its my first bet 2xx - 1xxx dollar repair

Feb 14, 2010 | 1993 Jeep Grand Cherokee

1 Answer

The cooling system on a 1993 Jeep. I fill up the


No you dont have to. first you need to find out the location of the leak. Check you water pump area pay attention on the telltale hole located underneath the pump shaft. look for any sign of dried up or wet anti freeze. also check your radiator pay attention on the area where the core and the plastic parts meet. any competent mechanic can accomplish a pressure test of your cooling system to determine the cause of your leak.

Aug 21, 2009 | Jeep Grand Cherokee Cars & Trucks

1 Answer

1993 Jeep Grand Cherokee, V6. Oil Pressure Gauge Read High.


it could be the sensor you should look at the oil pressure relief valve

Jun 10, 2009 | 1994 Jeep Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...