Question about Ford F-150
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Please Help ME by Remembering to RATE ME Thank you Vrey Much !!!
This vehicle does not use an external fuel tank switching valve. A supply check valve in the fuel pump assembly opens when the outlet pressure from the energized fuel pump exceeds the opposing check valve spring force.
R E C A L L 1991
THE DUAL FUEL TANK SELECTOR VALVE MAY MALFUNCTION AND CAUSE AN OVERFILL CONDITION IN ONE OF THE FUEL TANKS, RESULTING IN AN OVERFLOW OF FUEL PAST THE FILLER CAP.
THE OVERFLOW OF FUEL PAST THE FILLER CAP CAUSES A FUEL LEAKAGE, WHICH CAN RESULT IN A FIRE WHEN EXPOSED TO A SOURCE OF IGNITION.
REPLACE THE DUAL FUEL TANK SELECTOR VALVE.
SYSTEM: FUEL TANK, AUXILIARY.
VANS AND LIGHT TRUCKS WITH DUAL FUEL TANKS PRODUCED IN THE FOLLOWING PERIODS: F150, F250, AND F350 LIGHT TRUCKS BUILT BETWEEN FEBRUARY 28, 1989 AND JULY, 1989; ECONOLINE BUILT BETWEEN FEBRUARY 28, 1989 AND FEBRUARY 11, 1991.
NOTE: FORD HAS AGREED TO RECALL THESE VEHICLES BUT PARTS ARE NOT YET AVAILABLE.PARTS WILL BE AVAILABLE IN DECEMBER 1991. YOU WILL RECEIVE A LETTER FROM FORD ADVISING YOU WHEN TO SCHEDULE AN APPOINTMENT WITH YOUR DEALER TO HAVE THE RECALL WORK PERFORMED. IN THE MEAN TIME, YOU CAN TAKE THE FOLLOWING PRECAUTIONS:FILL EACH TANK TO ONLY 1/3 FULL. IF YOUR VEHICLE LEAKS FUEL OR IF YOU SMELL FUEL, STOP USING THE VEHICLE AND CALL FORD AT (313) 446-4654 AND ADVISE THEM OF YOUR PROBLEM. REFER TO FORD SAFETY RECALL NUMBER 91S39. AN OPERATOR WILL TAKE YOUR NAME AND TELEPHONE NUMBER. A FORD REPRESENTATIVE WILL CALL YOU BACK
Posted on Jan 21, 2009
SOURCE: Location of EGR Valve
Found the info!!
This Dodge EGR valve is a certain kind of device that is mounted right on your intake manifold which controls the amount of exhaust gasses back into your engine.
On a 2005 Dakota with 4.7 liter engine (non-HO), the EGR valve is located near the intake manifold on the driver's side right up against the firewall. It's hard to spot as it sits lower than the intake manifold. To change it, remove the electrical connector. There's a red tab that needs to be pushed to one side and then you have to squeeze down on a tab to get it free. Using a 13 mm socket, remove the bolt that you can see. I had to use a 3 inch wobble extention and then a 8 inch extension with a deep well socket to reach it with my 3/8 inch ratchet. There's a second bolt that you can't see between the EGR valve and the firewall. With a little trial and error and a lot more luck, you can reach the hidden bolt with the 3 inch wobble extension and a 13 mm deep well socket. Attach the ratchet after the socket is on and remove. This one isn't easy and if there's any Dodge engineers reading this one, a couple of extra inches of clearance between the valve and the firewall wouldn't have killed you no matter what the cost accountants said. With both bolts removed, you should be able to pull out the metal pipe that connects the manifold to the EGR valve out of the manifold (Pull to the right) and then you can lift the valve out. For assembly, the metal pipe connecting the intake manifold the EGR valve has to be removed and reinstalled on the new valve. It's held on with 2 5/16th" bolts. You should put the rear bolt on tight, but leave the front bold loose for the reinstall as some adjustment is necessary to get it put back together and the rear is a pain to tighten when installed. Line up the bolts that attach the valve and get the rear 13 mm bolt (The one you couldn't see on disassembly) started. Do not start the other 13 mm bolt as you'll need to pivot the valve and pipe to the left in order to reinsert the pipe into the intake manifold. Once the pipe is in the intake manifold. Start the other 13 mm bolt and tighten both 13 mm bolts and then the 5/16" bolts holding the pipe onto the valve. Reinstall the electrical connection. Please don't forget to rate!!!!
Posted on Mar 14, 2009
1st of all when Ford started out with putting "EGR's" on those diesel engines, they rushed it and are nothing less than a pain in the ***! i recommend having an EGR cleaning service performed by your local Ford dealer, i know they charge up the wazoo, but they're the best people to perform the service period.this is a VERY common problem with those engines and that service is "supposed" to be performed every 30K I believe. i dont recommend attempting to remove and service it youself, this WILL only make it worse.
Posted on Mar 26, 2010
Testimonial: "Im relieved to here that someone else is thinking the same thing. Im still going to try it myself as i am somewhat skilled at this but Thanks a bunch!"
Tips for a great answer:
Mar 27, 2016 | Ford Cars & Trucks
Mar 01, 2014 | 1999 Ford Expedition
Apr 06, 2011 | 1988 Ford F 250
Jun 25, 2010 | 1988 Ford F 250
Mar 03, 2010 | 1996 Ford Explorer
Jan 28, 2010 | 1995 Chevrolet K1500
Sep 14, 2009 | 1988 Mercury Cougar
Feb 24, 2009 | 2000 Ford Ranger SuperCab
Aug 24, 2008 | 1996 Ford Probe
May 23, 2008 | 1988 Ford Bronco
125 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: