Question about 1992 Buick Roadmaster

1 Answer

Changing axle seals, need to take out axles, where is the c-clip that holds the axles in place

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Am tryin to change the rear end sells in my 92 Buick roadmaster

Posted on Apr 22, 2011

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace my inner axle on the passenger side of my 2002 Dodge Ram 4x4 4.7L. I lent my truck out and the C clip let go of the CV axle. The intermediate axle spline is stripped and I need to change...


Lift and support front end on suitable jack stands preferably on frame. Remove right front cv axle, stub shaft, and seal. You will need to pull the right front brake caliper assembly loose and place to the side. Then remove bolts from shock and upper control arm and hub nut to do this. Next, remove axle lock actuator on passenger side of front axle. Place a drain pan underneath front diff cover and remove cover and drain axle. In the center of differential there will be an 8 mm head bolt holding spider gear cross-shaft. Remove bolt and cross-shaft only! Push inner axle in until clip clears inside of passenger spider gear. Set clip aside and push/pull axle shaft straight out to passenger side.

Feb 09, 2015 | Dodge Cars & Trucks

1 Answer

The right rear axle is bent on my 2005 Ranger. How do I remove and replace this axle? Does it have a clip that locks it into the differential?


kiker graham, Yes there is a clip that holds the axle in the differential. First jack up the back of the vehicle and support with jack stands. Put the transmission in neutral. Remove the wheel and brake drum from the axle you want to remove. Place a catch basin under the differential and remove all the bolts on the rear cover of the differential. Remove the cover and let the gear oil drain out. You may have to move the break line to remove the cover. When the oil has drained out turn the drive shaft until you see a small bolt in a recess on the right side of the assembly on the opposite side on the main drive gear. This is an 8MM bolt that has to loosened very carefully. First, using a punch, place the punch on the head of the bolt and hit it a few times with a hammer to "loosen" it up. This is done to avoid breaking the bolt. If this bolt is broken then you are going nowhere with this job. BE VERY CAREFUL when removing this bolt. When the bolt is out you can move the pin that it is holding. You will notice that this pin is very close to the ends of the axles. Do not completely remove this pin as the side gears will fall out. Pull the pin out only as far as you need to, to push the axle in towards the center of the vehicle. There is a C clip that will fall out when you have done this. Sometimes you have to spin the C clip to get it to fall out. Pull the axle out only far enough to put the center pin back in place. After you do this push the center pin back in and put the small bolt back in to hold it in place. Remove the axle. If the axle is bent and you say it is then it would be a good idea to replace the axle seal at this time. You can use the axle itself to remove the seal. Use the groove where the C clip sits. Place on the inside of the seal. Using the axle as a pry bry, remove the seal. Replace the seal and put the new axle in. You will have to move the axle around a little to get it to engage the splines on the inside of the side gear. Once again pull the center pin out only far enough to push the axle all the way in. Place the C clip in the slot at the end of the axle and pull the axle out as far as you can. This wont be much. Push the center pin back in and replace the little lock bolt and tighten it up. Clean the cover and the back of the differential and use silicone to seal it. There is a fill hole on the front side of the differential. The plug for this hole will accommodate a three eigths ratchet. Fill the differential until the gear oil starts to spill out of the hole. Replace brake drum and wheel. Good luck with this.

May 13, 2011 | 2005 Ford Ranger

2 Answers

I have greese all over the rear brakes


Rear Axle seals are bad, they must be replaced. Good Luck

Jan 14, 2011 | 1993 Ford Econoline

1 Answer

Change rear whell seal 1997 f-150 gear oil comeing out of rear whell took tire off; took drum off; and saw gear oil all over brake shoes. Seal or bearing need to be replace? how?


replace the axle seal to replace pull the rear cover draining the gear oil then rotate the carrier around till the small bolt holding the carrier pin remove bolt pull pin out don"t turn carrier after pulling the pin push the axle in and remove the clip from the inside of the carrier that pin holds the axle clips in place after pulling out you can remove the axle then just pop the seal out and install new one use a socket or something that is the same size as the seal lube the axle and slide axle back in lift up when almost all the way in the tube putting it in the carrier once in replace clip and pullout on the axle thats it pretty much hope this helps you out

Mar 24, 2010 | 1991 Ford F250

2 Answers

How do you remove the rear axle to change the axle seal, from a 2004 Coloraro?


remove the center cover facing the rear of the truck. you will see side gears with the shafts axle end at each side gear. a C clip will have to be removed from each shaft at the end of each axle. Then remove the wheels and pull out the axles

Feb 06, 2010 | 2004 Chevrolet Colorado

2 Answers

Rear end


Did you pull the pin at differential just to be sure? If it's non-"C" clips, you'll need a slidehammer attached to hub, over studs & use wheel nuts to hold it on there. Get er done !

Apr 24, 2009 | Chevrolet Monte Carlo Cars & Trucks

1 Answer

Replace axle seal on 2003 lincoln town car


You have to remove the differential housing cover.
Then turn the center housing until you can see the 5/16 bolt that holds the center pin that goes thru the spider and axle gears.
Remove the bolt and center pin,be careful that the gears stay in place.
Then push in on the axles to expose the c-clips on the end of the axles and remove the c-clip.
Then remove the axle.

Mar 25, 2009 | 2003 Lincoln Town Car

1 Answer

Does anyone know how to change seals on rear diff on 2003 frod expedition


if you need to change the axle seals here is the process. You need to remove the rear wheels. Remove the brake drums if so equipped. Remove the rear cover on the differential. Turn the differential until you find the bolt that holds the cross shaft in place. Remove the bolt and pull the cross shaft out. Then you will see the axle ends. Push the axle in towards the center of the axle. You will need to remove a C clip retainer from the axle end. You can then remove the axle and gain access to the seal. Repeat the process on the opposite side. Then reverse the disassembly process. Place the cover back onto the differential housing and refill the differential. Good luck.

Mar 03, 2009 | 2003 Ford Expedition

1 Answer

Need to know how to change rear wheel bearing in a 95 suburban


jack & support vehicle. remove rear axle cover drain fluid, removeleft rear tire drum/rotor brakes, remove bolt in axle housing that holds the 3/4 inch pin in place pull pin , push left axle shaft inwards and remove c clip from inside axle case,slide out axle shaft,remove seal,remove bearing and install in revers

Jan 16, 2009 | 2003 GMC Sierra

1 Answer

2005 Yukon Front Diff Axle seals


You don't have to remove the whole diff to change the seals, but you will have to seperate it where the shaft meets the carrier housing. There is a clip holding the passenger axle shaft in place that you have to remove to change the seal. The drivers side axle stub can be removed with a little force as there is a spring clip holding that side in.

Sep 01, 2008 | 2003 GMC Yukon

Not finding what you are looking for?
1992 Buick Roadmaster Logo

Related Topics:

138 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...