Question about Hyundai Accent

2 Answers

I own a 2004 Hyundai accent 1.6L DOHC. Had to replce valves, head gasket, timing belt and water pump. How do you time the cam and crank, as well as, cam to cam timing? I pin hole of the cam spocket is 12 with the cam shaft line going verticle. The cranks timed at 1 or 3? and with what mark? Lastly the cam to cam timing marks point left and right when the exhuast cam is sitting at 12? Thanks a diagram would be helpful

Posted by on

  • sean_hawn19 Mar 27, 2011

    I already kind of knew how to time the cam and crank but needed to know how to time cam to cam with the chain close to the cps. I can't find a repair manual for my car and we don't have auto zone around here in Canada. Still need a diagram like originally asked. On my car engine.

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 5,370 Answers

To get the complete guide.Its in parts.Click this link directly and get the instructions for the parts and timing:-----For part 1 click this link:--- http://technoanswers.blogspot.com/2011/03/how-to-time-cam-and-crank-on-hyundai.html ---------------------------- For part 2 click this link:--- http://technoanswers.blogspot.com/2011/03/how-to-time-cam-and-crank-on-hyundai_27.html ------------------------- For part 3 click this link:--------
http://technoanswers.blogspot.com/2011/03/how-to-time-cam-and-crank-on-hyundai_5630.html -------------------- For part number 4 click this link:----
http://technoanswers.blogspot.com/2011/03/how-to-time-cam-and-crank-on-hyundai_2497.html ---------------- In this parts its complete removal and disassembly of crank shaft and cam shaft assembly and exact timing procedure.---------Check all the part one by one, by clicking the links.------- This will help.Thanks.Helpmech.

Posted on Mar 27, 2011

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,382 Answers

Hi, the cam shaft has a hole on the hub that should be at approximately 12o'clock a red mark should be visible through the hole. the cramk shaft sprocket has a marking to align with the mark along the case, the keyway should be at about 3o'clock. be sure you at TDC on cylinder 1.
You need to get the car repair manual if you want to see the diagram or call auto zone...

Posted on Mar 24, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I replace timing belt but cant set timing


Hi Robert, It would help to know what engine is in your vehicle? A rule of thumb way to set up the valve timing is as follows. Rotate the crank shaft until the crank shaft mark is about 90 degrees from TDC. This will protect the valves from damage when rotating the cams to align them. With the tappet cover removed rotate the cam shaft or shafts so that the number one cylinder is on compression (both inlet and exhaust valves fully closed) and the last cylinder in line on overlap, Look for adjacent timing marks on the cam gears and somewhere close to those look for the alignment marks (maybe notch marks, holes or indented match marks). (Some manufactures use the machined gasket surface where the tappet cover closes onto the cylinder head). Look closely for the static mark on the cylinder head and align the cam(s) to it or them. Once completed, set the crank at Top Dead Center and look carefully for a timing mark which aligns with the gear and set them. Fit the belt so the marks align when the tensioner bearing is released and presses the belt under load. (follow the manufactures recommended tightening instructions.) . (Remember never to crimp a timing belt, if it has been, throw it away and get another, even if it is new!) If the belt snapped and that is the reason for replacement, internal damage may have resulted inside the engine. A snapped belt may cause damage to the valves, the camshafts, the cam shaft caps and to the pistons. If the engine turns much faster than expected and sounds as if there is no compression, you have problems! (Those I've just mentioned. I hope not for your sake. best of luck Regards John

Dec 12, 2011 | 2000 Hyundai Accent

1 Answer

I own a 2004 accent with 122,000 km on it. Long story short, had to get a new head gasket put on, so rocker cover, cams, everything had to come off. Work was done and everything was put back together. I...


P0340 - Cam Timing

SYMPTOMS/CONDITIONS
of a mistimed camshaft system (all must apply):
  1. Camshafts have previously been removed from the engine.
  2. Engine runs rough.
  3. Vehicle sets P0340 (camshaft sensor code).
  4. Camshaft sensor has been checked with a known, properly operating camshaft sensor.

CORRECT:
The diagram in the manuals should show the timing marks on both cam gears to be on the blue timing chain links.

ghost45_11.jpg

Mar 23, 2011 | Hyundai Motor 2004 Accent

1 Answer

I need to know how to replace a water pump on a 2002 hyundai gx 350.


2002 Hyundai XG350 3.5L MFI DOHC 6cylWater Pump - Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    Negative battery cable Accessory drive belts Water pump pulley Timing belt, tensioner and idler pulley Water pump

  4. 1514f36.jpg

    Fig. Water pump assembly-XG 300 and XG 350 (click over pic for zoom)

To install:
  1. Clean all mating surfaces of any residual gasket material.
  2. Install or connect the following:
    Water pump with a new gasket and torque the bolts to 16 ft. lbs. (22 Nm) Tensioner and timing belt and idler pulley Water pump pulley and drive belts Negative battery cable
  3. Fill the cooling system to the proper level.
  4. Start the vehicle, check for leaks and repair if necessary.
To install:
  1. Clean all mating surfaces of any residual gasket material.
  2. Install or connect the following:
    Water pump with a new gasket and torque the bolts to 16 ft. lbs. (22 Nm) Tensioner and timing belt and idler pulley Water pump pulley and drive belts Negative battery cable
  3. Fill the cooling system to the proper level.
  4. Start the vehicle, check for leaks and repair if necessary.

95486b3.jpg


Fig. Water pump bolt lengths-3.5L engine

Install the water pump with new gaskets and O-rings. Tighten the bolts to the following specifications:
  1. 1.5L SOHC engine: 105-132 inch lbs. (12-15 Nm).
  2. 1.5L DOHC engine: 14-20 ft. lbs. (20-27 Nm).
  3. 1.6L DOHC engine: 14-20 ft. lbs. (20-27 Nm).
  4. 1.8L, 2.0L, and 2.4L engines: 14-20 ft. lbs. (20-27 Nm).
  5. 2.5L engine: 11-16 ft. lbs. (15-22 Nm).

Hope helps (remember rated this).

Jun 18, 2010 | 2002 Hyundai XG350

1 Answer

We need to know where the cam timing marks go on a 1998 Hyundai Accent.The cam was turned after the belt was removed. We need to know how to aline the camshaft.


Hi

The cam dowel should be at 12:00. the hole in the cam sprocket should be line up with the cam dowel, with cam sprocket assembled to cam, you will see looking through the cam sprocket a red marking on the head, which lines up with the dowel. Down at the crank, make sure the cut out mark on the crank spocket is lined up with the notch on the oil pump cover.

Thanks for using FixYa - Steve




Feb 20, 2010 | Hyundai Motor 1998 Accent

2 Answers

Timing belt snapped


hi from uk the cambelt timing marks for accent 1.3/1.5 petrol are as follows= the cam cog has a hole drilling between the outer toothed and the central securing bolt this hole at TDC number 1 cyl is at top central and lines up with a V cut in the cyl head at rear of cog ? the crank cog at TDC number 1 cyl is a pop mark on both the cog and on thefront face of engine quite noticable ! these line up and are at approx 12 -30 pm when viewed fit new belt from crankcog in anticlockwise ie crank then cam then tensioner HOWEVER! if you are considering just replacing belt and tensioner ? be warned this engine is an interferance engine that is to say if belt fails whilst driving there may/will most probably be damage to the valves (bent) due to contact with pistons so would advise caution and suggest compression test all cyls after fitting new belt and tensioner and before rebuild completely once valves have bent they will not contact pistons again but you will have serious missfire/s and probably back fire up inlet manifold coupled with failing to start if engine is high milage ? consider removal of cyl head and check? de coke and replace damaged or best all valves then engine will have improved performance and more milesin future hope this helps

Nov 28, 2009 | 2001 Hyundai Accent

3 Answers

How Do I Change the Timing Belt on my 2004 Accent?


The timing belt is inside the valve cover. You have to remove the the valve cover gasket. Underneath that you will find the valves, the head (the top of the engine block). There is a pulley that is used to tighten the timing belt. The pulley is attached to the piston and valve timing. This pulley is usually marked as to where it should be positioned in relationship the timing of the pistons and the cam shaft rotation. This is what is referred to as stting the timing in the engine, and the timing of the distributor. Since your belt is broken the engine has lost track of its timing, so you might have to refer to a manual on your model of car to set the timing. You will also need to replace the valve cover gasket when you put the valve cover back on.

Dec 18, 2008 | Hyundai Motor 2004 Accent

1 Answer

Scheduled factory recomendation maintanence


you can buy a complete timing kit which includes, cam seals, crank shaft seal valve cover gasket, water pump the timing belt tensioner pullies and the timing belt idler pullies, if you can t find the kit the above mentioned parts can be bought seperately, and of course dont forget the timing belt! and please rate me also.

Dec 04, 2008 | 2004 Toyota Corolla

1 Answer

Would like to know if water pump needs to be changed when doing timing belt on 2004 hyundai santa fe 2.0 liter and how long of a job is it


Hi....
On your 2004 Santa Fe.
The water pump is not driven by the Timing belt.
Is not stricttly nessesary to replace togheter. they are individual.
But I recomend replace the timing belt when you replace the water pump. Because for get axces to the water pump,
you need to remove all the Timing covers.
Is just a few more minutes to remove the Timing belt.
Inspect the Engine seals, cam and crank Replace if need.
My PC show me a 2.4L 4cyl. for 2004 santa fe.

Ok.. The labor for that job Removing the Timing belt and water Pump ...IS:
2.8 hours. just the water pump 2.4 hours.

OK.. I hope this help on your question...
Thank you for use fixya..

Aug 13, 2008 | Hyundai Santa Fe Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

381 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...