Question about Chrysler Crossfire

1 Answer

Chrysler crossfire 2004 3.2cc, does turnover sometimes, one day it will start and one day it will not, ignition lights come on

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 2,510 Answers

It could be a number of things, starting with the ignition key switch starter contacts which could be only making contact intermittently. Then there could be a starter relay doing the same thing. Otherwise it could be the solenoid on the starter sticking and not making the contacts that actually power the starter and then the starter itself which could have worn or sticking brushes or a bad contact or loose wire on the commutator. Lastly, if the vehicle is an automatic, the switches that cut out the starter in all but Park and Neutral could be faulty. One cannot discount the possibility of a bad connector in the wiring either.
Sorry, but there are just too many possibilities, but most often it is the starter key switch or the solenoid. From here it is a process of elimination.

Posted on Mar 24, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What would make a 2004 Chrysler crossfire start but only idle a short time

Engine sensor , ignition control sensor ! Is the vehicle check engine light on ? Do you have a scan tool to check engine sensor data ? Do you have a DVOM - digital volt ohm meter ? any sensor that is powered by the PCM - engine computers five volt reference voltage circuit . 5 volt reference or crankshaft postion sensor . Doing testing is the way to find the problem .Check out videos on ignition system testing .

Feb 04, 2017 | 2004 Chrysler Crossfire

1 Answer

What would make the ignition switch stick an not turn to start the motor

Clyde, try moving steering wheel back and forth while trying to turn key. This sound like it should have been a recall for faulty ignitions as when I googled it, there are a lot of cross fires with the same problem. Clyde, google search (2005 crossfire ignition switch)
There is just too much for me to write.

Feb 23, 2016 | 2005 Chrysler Crossfire

1 Answer

Chrysler crossfire ignition key will not turn to start car?

Have you tried wiggling the steering wheel? I have a 2005 and mine does that sometimes, but I wiggle the steering wheel back and forth and finally the key starts the car.

Jun 25, 2014 | 2004 Chrysler Crossfire

1 Answer

How do you resett service counter on a chrysler crossfire

Switch ignition ON and immediately press button [A] 105730 twice. Switch ignition OFF. Press and hold button [A] while switching ignition ON. After 10 seconds the new interval will appear in the display [B] accompanied by a beep. Release button [A]. Switch ignition OFF.

Jan 27, 2010 | 2004 Chrysler Crossfire

2 Answers

2004 chrysler crossfire resetting service light

Disconnect negative battery post for 30 seconds & reconnect. This action will reset the car's computor & remove the light.

Jan 07, 2010 | 2004 Chrysler Crossfire

1 Answer

My crossfire shuts off randomly while driving. I try to start it back up and it does nothing.. turn the key and all lights on dash light up fine but no crank. Sometimes will turn car off and come back to...

does your car have a alarm system in it?

mabye the immobiliser kicks in you need to take the car to a car alarm place and get them to look at it

if you want to do it your self
on the lines going to the ignition barral are wires for starter and one for ignition
when wiring the alarm these wires are cut and then sent to the alarm control box
you need to find out which wires are which in the ignition barral and connect them normaly like they came out of factoryon a temporailly bais to see if this cures the problem

Dec 31, 2009 | Chrysler Crossfire Cars & Trucks

4 Answers

Chrysler Crossfire will not start

It turns out that the fuel pump relay is the problem and that this (per chrysler) is a common problem with the crossfire.

Jul 01, 2009 | 2004 Chrysler Crossfire

4 Answers

04 Crossfire not starting

Same thing happened to me. It was giving me problems starting it. It died on me at the stop sign last week. I kept driving. On Friday it shut down on me while doing 60mph on the hwy. I towed it to the nearest dealer. The said they had top replace the cranck sensor and a cam sensor. I paid $1,043.01 for that. Today I couldn't start it....

Sep 20, 2008 | 2004 Chrysler Crossfire

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides