Question about 2003 Jeep Wrangler

Open Question

Code p0158 came up can you tell me the problem

Posted by on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

After fixing p0132 p0138 p0152 p0158 I erase codes after light comes back on

make sure you have erased the codes , if you are sure they have been erased , and they come back, the fault has not been fixed.

Apr 03, 2017 | Cars & Trucks

1 Answer

Problem with p0158 code and my truck

Code 158 is for the signal coming from O2 sensor bank two sensor two being too high.
The sensors tell the computer if the fuel mixture is rich or lean. The sensor in question is after the catalytic converter, and the signal is higher - richer than it should be or it does not come down to normal range.
Usually the sensor has failed, but it could also be other issues.

Feb 22, 2013 | Dodge Cars & Trucks

1 Answer

Had code p0058 come up, so i replaced the co2 sensor. After a few days engine light came on with code p0158....which appears to be almost the same code. whats causing p0158 if ive already changed the...

This vehicle is equiped with 2 O2 sensors 1 is before the Cat converter and 1 after the Cat converter this code is for the 1 after the Cat converter or the most rear sensor not the first 1 change the farthest one from the engine and your problem should be solved.

Apr 29, 2011 | 2004 Dodge Durango

1 Answer

2001 Cherokee 4.0 6cyl -- P0161 and P0158 codes

If you do not know what the codes are, it is O2 sensor. This means the computer is not reading the right information from the faulty sensor. (there is a set range the sensor is meant to show, if one goes over or under the computer shows check engine). The diagnostic is not too bad, give the car a tune up, plugs, wires etc. and replace the O2 sensor. This normally clears up any problems. Let me know if you need further clarification or help.

Sep 28, 2009 | 2001 Jeep Grand Cherokee

1 Answer

08 highlander...VSC & check engine light came on....

Code PO158= Oxygen sensor, bank 2 sensor 2. On a V-6 it will be opposite side of engine from #1 cylinder & after catalytic converter

Feb 05, 2009 | 2008 Toyota Highlander

1 Answer

'08 Highlander...VSC & check engine light came on....

Hello/ The P-0158 code realtes to the Oxygen Sensor.

Specifically, it is as follows: Oxygen Sensor Circuit has High Voltage; Bank 2 Sensor 2.

If it under warranty, take it to a dealer to get it replaced free of charge. If not, go tho a dealer and tell them that you want Oxygen Senso Bank 2, Sensor 2, and have them tel you where it is. Please do not buy an "aftermarket" sensor, they have been known to read incorrectly, and you problem will not be solved.

I hope that this helps you, and that you will award me a "FixYa" rating for my assistance. 4 blue diamonds. Thanks.

Feb 05, 2009 | 2003 Toyota Highlander

1 Answer


OBD Code P0158 02 Sensor Circuit High Voltage (Bank 2 Sensor 2). Hope this gives you some direction. Thanks for Using FixYa!



Nov 28, 2008 | 2002 Jeep Grand Cherokee

Not finding what you are looking for?
2003 Jeep Wrangler Logo

Related Topics:

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

80339 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides