Question about 1996 Chrysler Town & Country
The fuelpump is located inside the gas tank,you will need to jack rear of van up, take caution the gas should be drained as far as it can be, this make thinngs easier, lkie handling the tank. first discoonect the connector to tank pump, on some of these the tank only need to be drop a little bit, the pump goes in from the top rear of the tank, you will need a jack you may need a board to put between the jack and tank, supprot tank and remove the two straps holding the tank, remove the hoses for the filler neck at the tank, next lower the tank, keep an eye out for hoses still connected, theres a vent hose and the two lines to pump, when you have enough room disconnect the lines. i have enclosed some diagrams to show you the pump which is a complete module and the location of the pump. the tank sits under the driverside center of the van, if you look you will see the filter next to the ring that holds the pump in.after removing the lines next remove the filter and replace that also with the new pump for warranty reasons and good to do.you will lower the tank , i would drop to the ground , this way you have plenty of room, with the tank empty you will be able to move it around , it make things easier.next is to remove the ring that holds pump in, remove by twisting counterclockwise, you may need to use a big pair of channel lock pliers, i use a dull chiesel and hammer to tap loose but use caution not to break or split the ring its plastic. with the ring off pull pump out, replace it with new, make sure to install new ring gasket that comes with the pump, next reverse to install you will need to line up the notches and push it down in tank and start the ring, its spring loaded so it will pop back up, hold it and start the ring and tighten it, hope this is helpful.
Posted on Mar 24, 2011
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
1996 Chrysler Truck Town &
Country 4WD 3.8L MFI 6cyl
The Fuel Filter is located under vehicle, driver side, below seating area, front of fuel tank, mounted on frame rail in fuel line.
Hope help with this (remember rated this).
Posted on Mar 13, 2010
Depends on how baddly the whole car is bent and how much you pay your self. You can do it, and if it's bent bad enought that you can't expect to pay mor than flat rate anyway because thier not just changing the bumper cover and or the bumper core and or the bumper core supports and or painting the new bumper cover and or replacing or straightening the care and even pulling the frame.. Most body shops and dealers will estimate this job but they have to see it because of the stroy I just told. They most often estimate for free as your insureance companies adjuster wight also. They may even come to your work or home to see the problem. If you want to keep the insurance man out of the loop then go to an auto parts store that sells auto paint and supplies. They'll tellyou about their customers and what to expect from them. and you'll hear alot of different prices, including look good or look good and be good and strong, all the prices wil be different.
Posted on Jul 19, 2010
Tips for a great answer:
Nov 29, 2014 | 1999 Chrysler Town & Country
Aug 08, 2011 | 1996 Chrysler Town & Country
Nov 19, 2010 | 1996 Chrysler Town & Country
Jun 04, 2010 | 1996 Chrysler Town & Country
Mar 13, 2010 | 1996 Chrysler Town & Country
Mar 06, 2010 | 1996 Chrysler Town & Country
Apr 09, 2009 | 1996 Chrysler Town & Country
Feb 21, 2009 | 1996 Chrysler Town & Country
Dec 17, 2008 | 1996 Chrysler Town & Country
1,016 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: