Question about 1999 Chevrolet Cavalier

1 Answer

1999 chevrolet cavalier standard transmition engage cluch car will start go into gear but will not move what is problem

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 388 Answers

The clutch pressure plate may have failed or the clutch plate may be worn to the rivets therefore not engaging the transmission. Either of these would be making a loud noise when the clutch is engaged. Another problem could be that the hydraulic fluid is low and not allowing the throwout bearing to engage the clutch. Get underneath the car and have someone push the clutch pedal down and make sure the arm that moves the throwout bearing is moving correctly.

Posted on Mar 24, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Here is my question: restated. My 99 Cavalier will not move at all. The emergency handbrake is not on. It goes into all of the gears easily, the car just does not move. What could the problem be?


Is your vehicle a standard or an automatic transmission? When you place the car into gear does the transmission click as though it wants to move?

Sep 02, 2016 | 1999 Chevrolet Cavalier

2 Answers

My chevrolet transport is no longer engaging gears, when i put it on drive or reverse gear, it doesnt engage


check fluid level in transmission . run the fault codes and look for a faulty TCM or torque converter clutch solenoid / servo

Mar 20, 2014 | 1999 Chevrolet Venture

1 Answer

My 1999 cavalier has a problem with trans. i shift it into gear and trans engages but doesnt move


Might start with filter in tranny befor replacing, If high millage may be time to rebuid. wish you best good luck.

Mar 29, 2011 | 1999 Chevrolet Cavalier

1 Answer

1987 porche 924 cluch problem


Hi. your pressure plate is going bad at this time. you will need to replace this part asap.

May 23, 2009 | 1987 Porsche 944

1 Answer

My clutch is not fully disengaging.


Your master clutch cylinder is probably leaking (internally; fluid bypassing the seals) or you may not have done a thorough job of getting the air out of the hydraulics. I have had to do it again a couple of times and now, after renewing the fluid, bleeding all lines of old fluid, I recirculate the fluid through a clear plastic tube draped over the driver's side windshield wiper and a bottle so I actually see the air bubbles fade after pumping long enough.   
If the slave cylinder is leaking, you should have some stains around the area where it is mounted on the bell housing. Many cars do have an adjustment at the slave cylinder that sets the starting point of its travel but I have found that these only very rarely need adjustment and don't change until the master or slave cylinder start to bleed fluid past their seals or the throwout bearing becomes really sloppy.  

Oct 23, 2008 | 1995 Chevrolet Cavalier

1 Answer

My 1998 chevy cavalier is having trouble going into gear. i can go in reverse and sometimes it won't shift into drive and car won't move, then it will act fine at times. it is an automatic and have checked...


let it warm up for 10 minutes before you put it into drive if it goes rite in then you need to change the transmition filter in it i had 2 chevys do that it will go rite int reverse gear but wont go into drive rite away after the engine runs for a while it shuld go into drive

Sep 23, 2008 | 1999 Chevrolet Cavalier

1 Answer

1988 Cavalier z24 transmition problems


try this :
with the car in park start it, then from park move it down one. if it is reverse move it down another one, now that should be neutral, then the next one should always be drive

Sep 03, 2008 | 1988 Chevrolet Cavalier Z24

Not finding what you are looking for?
1999 Chevrolet Cavalier Logo

219 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...