Question about 1991 Chevrolet S-10

1 Answer

91 S-10 how do you get the rear brake cylinder off.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

There is a clip on the back of the cylinder by the bleeder nub holding it to the back plate. you need to use a curved needle-nose pliers or 2 awls in to the access slots between the retainer locking tabs and bend them both away at the same time. hope this helps

Posted on May 04, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why even with new brake parts in the front and rear on my 2995 Ford f150 2wd truck would front brakes work but not back ? I even put truck on bay lift and hit the brakes and rear just kept spinning.


Bill:

Check your master cylinder. It could be a piece of junk lodged in the fluid port for the rear brake lines, or in the brake line its self. The fact that both rear wheels spin tells me that if it is a clogged line, it is between the two manifolds, (one next to the master cylinder, and the other where the rear brake line splits into two... one for each rear hub. Or it could be that the piston in the master cylinder needs to be replaced. I would disconnect one brake line at one rear wheel and disconnect the rear brake line at the manifold (near the master cylinder)and blow that line out with air pressure. . do not leave the rear brake line connected to the master cylinder as you blow air through the lines as you may damage the master cylinder piston packings. You'll have to bleed the brakes when you are done.

Jan 24, 2016 | Ford Cars & Trucks

1 Answer

Grease in rear wheel hub


The rear brake cylinders are located inside the hub with the brake shoes on drum brakes...(common in 2004 Rangers on rear only) The brake cylinders are a "wear item" with seals...we used to rebuild the cylinder with new seals...best today to buy new brake cylinders to replace the leakey ones...You will need to bleed all 4 brake line/wheel connections after the replacement. Hope this helps.

Oct 14, 2013 | 2004 Ford Ranger

1 Answer

Is there two brake lines to rear


rear brakes has two brake lines from mastercylinder to both rear wheels cylinders. front brakes has two brake lines from mastercylinder to front brake calipers for each front wheel.

May 07, 2013 | Cars & Trucks

1 Answer

On right rear of 98 jimmy, when brake pedal applied. fluid is "squirting " out


check right rear wheel cylinder.the wheel cylinder bleeder screw could be loose or brake line to rear brake hose or brake line broken.the rear wheel cylinder seal is leaking brake fluid.

Apr 10, 2011 | GMC Jimmy Cars & Trucks

1 Answer

My brakes had began to fail. I tried adding brake fluid, they got worse. So I took it in for repair to a local shop, they said I needed a new master cylinder and added one. I had been driving my car for...


1- New master cylinders could also fail, possibly due to bad quality replacement parts or maybe even just a factory fault on a good quality master cylinder.

2- If you had blown a rear wheel cylinder, you most deffinatly should still have had a form of front brakes. the reason for this is as follows... For this very saftey meassure manufactures design the container for the brake fluid supplying the master cylinder in two internally, so this would mean that if you where to drain all the brake fluid through the rear wheel cylinders an acceptable amount of brake fluid should still remain within the one compartment of the reservoir for the front brakes to still opperate.

3- Leaking rear wheel cylinders should have been noticed by the technician who installed the master cylinder, the reason for this is because the brake fluid would have had to be bled through the system at each wheel. even though it would have been performed from the back of the wheel one would expect the technician to notice the brake fluid dripping out behind the brake drum.

I hope the above is of assistance to you.

Regards.

Feb 21, 2011 | 2001 Ford Taurus

2 Answers

1995 buick lesabre. brakes are gone! fluid leaking from left rear brake.


If they are drum brakes then it is most likely the wheel cylinder. these are not expensive but you will need to replace the rear brake shoes and clean all the parts with brake clean. I recomend replacing the other cylinder while your at it.

Nov 22, 2010 | 1995 Buick Regal

1 Answer

Hello. i have a 1991 audi 100. brake padel has become mushy but there are no signs of brake fluid leak on the master cylinder or the lines. the brake pads are new. thanks


Just because there isn't an external leak in the brake system doesn't mean there isn't an internal leak in the master cylinder. A mushy pedal is usually an internal leak in the master cylinder or leaking wheel cylinders in the rear brake drums. Check the rear brake wheel cylinders for fluid leaks, if there are none or you do not have rear drum brakes, your best bet is the master cylinder :)

Sep 03, 2009 | Audi 80 Cars & Trucks

1 Answer

"I just had a new brake booster Master Cylinder rear wheel cylinders and rear brake shoes installed, I drove 3 miles and the back brakes locked up. What can this be? 1998 chrysler sybring


Sorry to but in BUT

is this a high mileage car from what you discribe new Servo, Master Cylinder, Cylinders and rear brakes.????

Try the rear flexible brake pipe/s OLD RUBBER DELAMINATES well worth the swop. For the cost

360 Volvos used to be good at this one only after a brake fluid change

Old British Mechanic

May 08, 2009 | 1998 Chrysler Sebring

1 Answer

I need a schematic for the rear brakes on an F150 super cab with 4.6L automatic trans 4wheel drive


Drum, Rear Brake System Standard Rear Brake
9969082.gif
Item Part Number Description 1 2069 Brake Shoe Hold-Down Spring Pin 2 — Rear Wheel Cylinder Retaining Bolt (2 Req'd) 3 — Washer (2 Req'd) 4 — Anchor Pin (Part of 2211) 5 — Wheel Cylinder 6 2028 Brake Shoe Anchor Pin Guide Plate 7 2A637 Parking Brake Lever 8 2296 Brake Shoe Retracting Spring (Short) 9 2296 Brake Shoe Retracting Spring (Long) 10 2200 Rear Brake Shoe and Lining (Secondary) 11 — Washer 12 2106 Parking Brake Lever Pin Retainer 13 — Brake Shoe Adjusting Lever Cable Guide 14 2A642 Primary Brake Shoe Parking Brake Lever Link 15 2A601 Parking Brake Link Spring 16 2068 Brake Shoe Hold-Down Spring 17 2A176 Brake Shoe Adjusting Lever 18 2048 Brake Shoe Adjusting Screw Socket 19 2047 Brake Shoe Adjusting Screw Nut 20 2041 Brake Adjusting Screw 21 2049 Brake Shoe Adjusting Screw Spring 22 2200 Rear Brake Shoe and Lining (Primary) 23 2A178 Brake Shoe Adjusting Lever Cable 24 2211 Brake Backing Plate
Heavy Duty Rear Brake
6dcb5d2.gif
Item Part Number Description 1 — Rear Wheel Cylinder Retaining Bolt 2 00538 Lock Nut 3 2212 Rear Brake Backing Plate 4 2262 Rear Wheel Cylinder 5 2A642 Primary Brake Shoe Parking Brake Lever Link 6 2A601 Parking Brake Link Spring 7 2A637 Parking Brake Lever 8 2106 Parking Brake Lever Pin Retainer 9 — Parking Brake Lever Bolt 10 — Secondary Shoe Assembly 11 2A179 Brake Shoe Adjusting Lever Cable Guide 12 2068 Brake Shoe Hold-Down Spring 13 — Adjusting Lever Pin 14 — Adjusting Lever Return Spring 15 2A176 Brake Shoe Adjusting Lever 16 2047 Brake Shoe Adjusting Screw Nut 17 2049 Brake Shoe Adjusting Screw Spring 18 2041 Brake Adjuster Screw 19 — Primary Shoe Assembly 20 2068 Brake Shoe Hold-Down Spring 21 2200 Rear Brake Shoe and Lining 22 2035 Brake Shoe Retracting Spring 23 2A178 Brake Shoe Adjusting Lever Cable 24 2092 Brake Adjusting Hole Cover 25 2069 Brake Shoe Hold-Down Spring Pin
The rear drum brakes:
  • Have internal shoes that expand against the brake drum (1126).
  • Are a single-anchor type.
  • Are actuated by one rear wheel cylinder (2262).
  • Have two pistons in the rear wheel cylinder (2261). One exerts force against the upper end of the primary shoe; the other exerts force against the upper end of the secondary shoe.
  • Adjust rear brake shoes and linings (2200) automatically.
  • Need manual brake adjustment if the adjusters are not operating properly or after the rear brake shoes and linings have been replaced.
When the brake pedal is applied, hydraulic fluid pressure forces the pistons in the rear wheel cylinder outward, moving the rear brake shoes and linings against the brake drum.
The rear drum brake system includes the parking brake mechanism. Refer to Section 206-05 .

Apr 04, 2009 | 1997 Ford F150 Regular Cab

1 Answer

Brakes (rear)


i would look at the othe rear wheel cylinder it is most likely leaking

Mar 08, 2009 | 1988 Chevrolet C1500

Not finding what you are looking for?
1991 Chevrolet S-10 Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...