Question about 2006 Mitsubishi Outlander

1 Answer

Just bought a 2006 Outlander.Should the automatic shifter (ie.drive, neutral rear, etc light up?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 207 Answers

No. Shouldn't matter

Posted on Mar 24, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clunk when pulling off from stop


check for worn loose "u" joints . check for loose drive shaft pinion. Check for worn suspension rubbers on rear end allowing the arms to move up and down

Apr 05, 2014 | 2006 Mitsubishi Outlander

1 Answer

Shogun warrior


Check your connections at the shifter and neutral safety switch. If you wiggle the shifter and it starts, the problem is close to the base of the shifter or the wiring harness to the transmission from the shifter. Look for loose connections or damaged wiring.

Mar 18, 2014 | 2006 Mitsubishi Montero

1 Answer

The neutral light on the dash board starts blinking when the gear is put in drive. what is the cause and solution


Same thing is happening with my cs3 2002 lancer,, only when in drive (in motion) it comes on and blinks once per second, got it scanned...they said it was the primary sensor, had it changed, problem still persists....help!!!!

Oct 01, 2012 | 2003 Mitsubishi Outlander

1 Answer

How do I remove the center console of a 1994 Buick Regal in order to repair the light gauge showing drive, reverse, neutral etc? (The plastic pieces on both the automatic shift lever and the indicator...


You should be able to remove the trim plate that where the shifter is, it the cover and from there you will be able to replate the bulb for the selector window,

Aug 29, 2010 | 1994 Buick Regal Gran Sport

1 Answer

Dual gate Hurst shifter adjustment


Hello! Here is what I was able to track down:

Hurst Dual Gate Shifter Assembly Parts Breakdown:


c73f4fe.gif

Removing & Replacing The Hurst Dual/Gate
1. Disconnect car battery.

2. Remove Knob. Remove four Phillips head screws that hold escutcheon plate down to console.
NOTE: SHORT SCREW IS USED IN REAR RIGHT - HAND HOLE. Remove escutcheon plate and console from floor tunnel.

3. Lift selector indicator lamp housing out of shifter and pull bulb socket out of lamp housing. Disconnect wire connectors from combination Back - up light / Neutral safety switch.

4. Remove two 1/4 - 20 x 1/2 hex-head cap screws that fasten Dual / Gate shifter to rear mounting bracket. Remove 1/4 - 20 x 1/2 hex - head cap screw that holds cable bracket to shifter frame. Remove two #10 - 32 x 3/8 slotted head cap screws that fasten Dual / Gate shifter to front bracket. Free shifter from cable by removing cotter pin and washer.

5. Remove combination Neutral - safety / and Back - up light switch. Install switch on Replacement unit.

6. Install replacement shifter unit in reverse order of removal of original unit.

7. ADJUST CABLE: SEE FIGURE 1 (Below)
Loosen nut that fastens cable pin to transmission control arm. Loosen nut enough to allow pin to slide in the slot in the arm. Turn the arm to NEUTRAL position. Move the stick to NEUTRAL. Tighten the adjusting nut. Test movement of stick and check to be sure that stick positions agree with transmission control operation.


43402db.gif
8. SEE FIGURE 2 (Below)
Connect car battery. Apply hand brake. Move stick to NEUTR AL position. Press foot on brake pedal. Start engine. If starter fails to operate, Neutral Safety switch must be adjusted. Adjustment is made with a long-bladed Phillips screwdriver through the "Street" gate. This screw is directly in front of the st ick. Turn the screw about 1/2 turn past the point where starter operates. (STICK MUST REMAIN IN "NEUTRAL" WHILE ADJUSTMENT IS MADE). Starter should operate ONLY when stick is in PARK or NEUTRAL position.


522a7e2.gif

Hope this helps and thanks for using FixYa!

Oct 22, 2009 | Pontiac GTO Cars & Trucks

1 Answer

Filler to add oil automatic transmission Mitsubishi Outlander 06


use the dipstick hole, you need a certain funnel. if you cant fiind it let me know.

Mar 07, 2009 | 2006 Mitsubishi Outlander

1 Answer

Will not let you put the 2006 h3 in drive running or not with


Try putting the key in the 1st position (steering unlocked but no dash lights) and see if you can shift to neutral and then start the car in neutral. If not check and see if the brake lights work with the car running if not check the fuses or the brake light switch. Good Luck.

Feb 11, 2009 | 2006 Hummer H3

Not finding what you are looking for?
2006 Mitsubishi Outlander Logo

Related Topics:

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...