Question about Ford Bronco II

Open Question

Is the intake manifold changeable from a ford 2.8v6 to the ford 2.9v6 , example are the intake manifold gaskets the same.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 58 Answers

SOURCE: Replacing an intake manifold gasket on 1993 ford ranger 4.0

I've replaced several of these gasets and they were made that way.
It wouldn't hurt to call a different autoparts store and ask them if theirs are made that way.

Posted on Jan 07, 2009

chuck943
  • 783 Answers

SOURCE: Ford 460 Intake Manifold Torque spec

22 to 35 ft lbs

Posted on May 22, 2009

gabndan2
  • 35 Answers

SOURCE: How to install intake manifold gaskets and their location.

go to autozone.com and register free then select make year ect.
select repair info (you have to register 4 this)
step by step and photos!!!!

Posted on May 31, 2009

lasvegasrich
  • 65 Answers

SOURCE: intake manifold gasket / replace

3.8L Engine

NOTE The 3.8L (VIN K) non-supercharged engine uses a two-piece intake manifold consisting of an upper air plenum which mounts the throttle body and a lower intake manifold assembly which houses the fuel injectors. The 3.8L (VIN 1) supercharged engine uses a similar lower intake manifold. The supercharger serves as the upper manifold.
Lower Manifold

NOTE Two bolts which fasten the lower intake manifold to the cylinder head are accessible only after the upper intake manifold is removed. These bolts are located in the right front and left rear corners of the lower intake manifold. Remove the upper intake manifold to service the lower intake.
The 3.8L (VIN 1) supercharged engine uses a manifold similar to the 3.8L (VIN K), but the supercharger serves as the upper manifold.

  1. Disconnect the negative battery cable.
  2. On 3.8L (VIN 1) engines, remove the supercharger assembly. Please see the procedure in this section.
  3. Remove the upper intake manifold using the procedure above.
  4. Remove the EGR outlet pipe from the intake manifold.
  5. Detach the engine coolant temperature sensor wiring harness from the sensor.
  6. Remove the lower intake manifold bolts and carefully lift off the manifold.

To install:


0900c15280269f1b.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Lower intake manifold bolt torque sequence-3.8L (VIN K) engine
  1. Clean all parts well with degreaser, especially the gasket seal surfaces on the upper and lower manifold pieces and between the lower manifold and the cylinder heads..
  2. Install new gaskets to the cylinder heads and new seals to the engine block. Carefully lower the manifold into place. Apply thread-locking compound to the bolt threads. Make sure to install the two hidden bolts in the lower intake manifold. Hand start all bolts, then torque evenly to 11 ft. lbs. (15 Nm). Follow the toque sequence, starting in the center, then working outwards in a circle.
  3. Install the remaining components in the reverse order of the removal process.

Upper Intake Manifold (Plenum)
  1. Disconnect the negative battery cable.
  2. On 3.8L (VIN 1) engines, remove the supercharger assembly. Please see the procedure in this section.
  3. Tag for identification, then remove the right side spark plug wires.
  4. Disconnect the ignition wires from the fuel rail.
  5. Remove the fuel rail. Please see Section 5.
  6. Remove the cable bracket from the intake manifold.
  7. Remove the throttle body.


NOTE Two bolts which fasten the lower intake manifold to the cylinder head are accessible are accessible only after the upper intake manifold is removed. These bolts are located in the right front and left rear corners of the lower intake manifold.
  1. Remove the upper intake manifold bolts and carefully lift the upper intake manifold from the engine.



0900c15280269f1c.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Upper intake manifold and bolt torque sequence-3.8L (VIN K) engine
To install:
  1. Clean all parts well with degreaser, especially the gasket seal surfaces on the upper and lower manifold pieces.
  2. Install new gaskets to the cylinder heads and new seals to the engine block. Carefully lower the manifold into place. Make sure to install the two hidden bolts in the lower intake manifold. Hand start all bolts, then torque evenly to 89 inch lbs. (10 Nm). Follow the torque sequence, starting in the center, then working outwards in a circle.
  3. Install the remaining components in the reverse order of the removal process.

Posted on Sep 16, 2009

  • 14 Answers

SOURCE: intake manifold gasket replacement? radiator has a

nah its pretty simple for the upper intake. 10 to 12 bolts.

Posted on Oct 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

Intake Manifold gasket replacement and/or leaking= Ford


Intake Manifold gasket~

Replacing intake manifold gasket:
Replacing the intake manifold gasket, I used the tube kind, it's a make it youself for about $6 (it's blue and the consistancy of toothpaste) follow directions carefully! You can get a tube at Autozone or any car parts store. Has been working great. Just ask the cashier for the make it yourself kind of intake manifold gasket. Sorry, I don't remember the name of it, it's been that long...lol...

As for the Intake Manifold leaking coolant....It could, but shouldn't. One of the largest problems I've seen for coolant to leak out the Intake Manifold has been due to pressure in the system somewhere... Check the classic area:
Water pump- look for either water seapage and/or coolant. You'll know if it is because you will see real water either coming out of the water pump leak hole or under the thermostat. Most of the time coolant will pool where your heater hose runs in the intake manifold.

Mentioning heater hose. Check for leaks, holes, and/or cracked heater hoses. In-addition to the water pump, heater hoses...Check the transmission system, exhaust system, fuel system, radiator system, A/C system, secondary fan (located above the water pump housing), and thermostat.Also, check all electrical connections....Hummm....This is almost the entire workings of the vehicle.

NOTE: "It seems to be an infinity kinda thing... Once one thing starts to fail and is ignored, you are bound to be fixing a chain of event failures. Therefore, Do not ignore even the smallest problem or you'll be bound for life in repairs...."

on Jun 25, 2010 | Ford Expedition Cars & Trucks

1 Answer

On a 2000 explorer 4.0 Soho do I have to remove the injectors to remove the lower intake


REMOVE UPER INTAKE 97 EXPLORER V6 4.0 - YouTube

? 12:22
https://www.youtube.com/watch?v=ugExJ0wkP8A
Jun 11, 2013 - Uploaded by Sum Guy
REMOVE UPER INTAKE 97 EXPLORER V6 4.0 ... I was told that all I have to do is remove the fan belt to get access to it ... FordExplorer 2000 intake manifold gasket upper lower P0174 by froggy - Duration: 36:54. by froggy 36,588 views ... Ford Explorer 4.0L SOHC Rough Idle P0171 P0174 Lean Codes ...

Putting the lower intake on my 1997 Ford Explorer 4.0 OHV ...

? 5:23
https://www.youtube.com/watch?v=qKE1vPxqPHs
Jun 27, 2010 - Uploaded by origionaldz
Putting the lower intake on my 1997 Ford Explorer 4.0 OHV sport .... I do have a 2000 5.0 ... @michaelheiland123654 To dothis job, you have to remove the alternator, unbolt the AC compressor, remove upper intake manifold, remove fuel rail,remove all injectors, ... Do you have the SOHC or OHV version?

1999 Ford Explorer 4.0L -need assistance on removing upper intake ...

www.automotiveforums.com > ... > Ford > Explorer ' Explorer Sport Trac
Sep 20, 2011 - 1999 Ford Explorer 4.0L -need assistance on removing upper intake ...Are you sure you have the OHV/pushrod engine and not the SOHC engine? ... Do youhave the upper intake manifold loose, you just are unable to ... the lower intake gasket, valve cover gaskets, Injector o-rings, plugs and wires. Thanks ...

How to replace upper intake manifold gaskets - Ford Explorer




Dec 09, 2015 | Cars & Trucks

1 Answer

WHO DO YOU REMOVE AND REPLACE THE MANIFOLD ON A 2001 FORD WINSTAR


Ford Windstar P0171 P0174 Intake Manifold Gaskets: http://youtu.be/HgHDhNzBJ8w

Feb 21, 2015 | Ford Cars & Trucks

2 Answers

How do i REPLACE INTAKE MANIFOLD GASKET ON 1989 BRONCO ii


Unbolt the Intake Manifold, install the new gaskets and bolt it back in place. My best advice to you is go to a auto parts store and buy a manual as it will tell you exactly how to do it.

Feb 02, 2015 | 1989 Ford Bronco II

1 Answer

How do you replace gasquet on air intake of 2004 ford focus


Unbolt the manifold bolts, remove intake manifold clean off old gasket with rotary wire brush or scraper ,fit new gasket and bolt back on.

Jul 28, 2014 | 2004 Ford Focus

1 Answer

Exaust intake leaking


It's exhaust manifold. There are two manifolds, the intake manifold in the valley between the cylinder heads, and the exhaust manifolds, one on each side of a v figured engine.

And, yes, a leak in the exhaust or the intake will make it run lean. If the leak is close to the engine, it can do harm to the valves, too. There is a gasket between the exhaust manifold and the engine block. Likewise, there is an intake manifold gasket between the intake manifold and the block.

Apr 04, 2014 | 1998 Ford F150 Regular Cab

1 Answer

Sorry, this may be a repost. I have a 1989 2.3 liter Ford Ranger i've been working on. I replaced the gaskets on the intake manifold and within two days a milky white substnce (oil & moisture)


The high idle is a vacuum leak from your work, as well
as the gasket issue is not resolved yet

Have to start over & check your work

Mar 06, 2013 | Cars & Trucks

1 Answer

Need to find a plastic Upper Intake Manifold for a 2001 Mazda Tribute 3.0L 6cy. Mine has a crack. A part number or a autoparts web site where I could order one from would be great. I've had no success...


The 3.0L Mazda should be the same as the Escape.
I found this website for Ford OEM parts (It's probably a Ford dealer);
https://www.silverstatefordparts.com/ford-escape-parts.html

Look under Intake Manifold:
Fuel system Cruise control Fuel induction Fuel injection Intake Intake manifold Manifold gasket

Intake manifold, escape, mariner, 3.0l, upper
01-04 ($214.98 List) $151.95
plus tax and shipping.
Don't forget the gaskets.

Apr 04, 2011 | 2001 Mazda Tribute

1 Answer

Sir, My ford windstar 1998 give me the code P0174,sytem too lean(bank2), can you tell me what the problem is , it gives a heavy white smoke when i start the engine . just put a new cylinder head gasket...


It's an intake gasket. Another option, however rare is the air flow meter. But not likely. The white smoke is most likely antifreeze leaking into either a cylinder, or the intake and entering a cylinder, exiting as white smoke. The bad intake gasket (or intake manifold) could be causing both problems. I'd try a new set of gaskets and just the upper half of the intake manifold.

Jun 10, 2010 | 2001 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...