Question about 1987 Suzuki Samurai

Open Question

1988 samurai clutch throw out pivot removal and throwout bearing

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 345 Answers

SOURCE: 95 golf clutch throw out bearing problem

take it your car is a mk3 ? if it is remove the end cover from the gearbox(you will need a new one) and you will see the release bearing on a fork,remove the center bolt pull out the shaft and replace it,usally takes about a hour and a half

Posted on Oct 19, 2008

  • 19 Answers

SOURCE: clutch removal

You have to insert a screwdriver through a hole in the bottom of the transmission. while pushing the fork away from the engine you push the retainer clip with the screwdriver blade. it should release the bearing and cause the cluch fork to move freely toward the engine. It may take you a few tries to do this. This is whats known as an reverse pressure plate assembly. I think its kinda stupid idea. If only the designers would look at what it takes to work on these things......m2242202_00014.png

Posted on May 26, 2009

  • 2 Answers

SOURCE: How do I change my clutch on an 1986 suzuki samurai

I have found it easier to remove the engine to replace the clutch on my 1986 Samurai it you have the proper tools to pull the engine it took less time than pulling the transmission in my experence.

Posted on Jun 28, 2009

  • 48 Answers

SOURCE: 87 suzuki samurai - What are the symtoms of a bad

The symptoms of a bad throwout bearing is a horrible noise that ONLY occurs when you are pressing on the clutch. And/or you have no clutch action at all - the car is either in gear or it's in neutral. Sounds just like your situation alright.

Usually bad throwout bearings damage pressure plate fingers to the point that they need replacing too. And while they are in there, they will want to replace the clutch disk too. And then lathe the flywheel flat again so that they don't have a repeat customer complaining about the lousy clutch $job$ he just got. Flat flywheels supposedly won't chatter on take off or clutch engagement, but it could be hose job where you get soaked as well.

I went this route once on a gremlin - $500. The only reason I paid up was that I had a real good job at the time, and then I've never been back either.

Posted on Aug 04, 2009

BCAS1298
  • 3092 Answers

SOURCE: clutch pedal goes to floor and stays 1999 Nissan

ON A 2000 MAX 6 CYLINDER HAS CLUTCH MASTER CYLINDER AND SLAVE CYLINDER, CHECK FLUID LEVEL AND BLEED CLUTCH SYSTEM AT SLAVE CYLINDER BLEEDER. HAVE NOT HEAR OF CABLE CLUTCH SYSTEM. ONLY HYDO.& LINKAGE. GOOD LUCK

Posted on Nov 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1988 suzuki samurai.when I'm driving down the road the transmission is whining. When I let off gas it stops. I just bought it it's has a new clutch and cable. Don't know if throw out bearing is new.


If it's not whining when you have your foot on the clutch and are stopped, its not the throwout bearing. While driving the throwout bearing isn't being used....
Transmission whine is either in the transmission or differential.

May 15, 2015 | 1988 Suzuki Samurai

1 Answer

No gears at allk


sounds like problem in the transmission shift top if it won't shift gears. If throwout bearing is not engaging pressure plate, it sounds like the pivot for the clutch acctuator is broken

Mar 05, 2014 | 2000 Ford Focus

1 Answer

So I heard my throw out bearing making some noise. When I push the clutch in the noise stops and when I let the clutch out the throw out bearing was howling a little. Then I was driving down the freeway in...


ooh this sounds bad your gonna have to remove the trans inspection plate and look to see what got damaged with light squeaky throwout bearings are a warning of bigger things to come could be a total failure of clutch packs and pressure plates

Oct 20, 2013 | Cars & Trucks

1 Answer

I hauled a trailer about 40 miles and when I went to leave the clutch pedal went to the floor no resistance and wouldn't disengage clutch master cylinder has fluid throwout bearing has been making noi


It sounds like the throw out bearing separated. You will want to change the clutch and pressure plate when you replace the throw out bearing.

Aug 18, 2013 | Cars & Trucks

1 Answer

1986 suzuki samurai clutch doesn't disengage


throwout bearing possibly, how does the clutch pedal feel?

Apr 03, 2010 | 1987 Suzuki Samurai

1 Answer

When the clutch is engaged,does the throwout bearing go towards the motor or away?


When your clutch is fully planted against the clutch disc and flywheel the throwout bearing is resting in the furthest rear position or towards the rear of the vehicle in the bellhousing, remember that the clutch release fingers work on a pivot point and lever action.
Good luck !

Jan 12, 2010 | 2001 Hyundai Santa Fe

1 Answer

How do you replace a throw out bearing on a 88 integra ls?


You must remove the transmission from the vehicle. The clutch release bearing (throwout bearing) rides on the input shaft of the transmission, and is the only part of the clutch kit that remains attached to the transmission upon removal.

Make certain you reattach the bearing retainer mechanism to the bearing fork, so that the bearing doesn't ride on the face of the pressure plate while you're not using the clutch pedal.

Dec 27, 2009 | 1988 Acura Integra

4 Answers

87 suzuki samurai - What are the symtoms of a bad throw out bearing? *It has a new cable* I can't get cable to adjust anymore. While pushung clutch car makes sqeeking and chatter noise and acts like clutch...


The symptoms of a bad throwout bearing is a horrible noise that ONLY occurs when you are pressing on the clutch. And/or you have no clutch action at all - the car is either in gear or it's in neutral. Sounds just like your situation alright.

Usually bad throwout bearings damage pressure plate fingers to the point that they need replacing too. And while they are in there, they will want to replace the clutch disk too. And then lathe the flywheel flat again so that they don't have a repeat customer complaining about the lousy clutch $job$ he just got. Flat flywheels supposedly won't chatter on take off or clutch engagement, but it could be hose job where you get soaked as well.

I went this route once on a gremlin - $500. The only reason I paid up was that I had a real good job at the time, and then I've never been back either.

Aug 04, 2009 | 1987 Suzuki Samurai

2 Answers

1993 Ford Ranger 4.0 I put a new slave/throwout bearing in. I went to put it in gear and the stick shift is stuck in the neutral position. It won't go into any gear. When I start the truck, it is stuck...


Have an assistant push in on the clutch while you observe the function of the cluth throwout bearing lever, it may be that the throwout bearing fork lever is not on its pivot point or is out of adjustment, you should be able to rotate the rear tires when the clutch is pushed in if not the throw out bearing and fork assembly either was not put in corectly or you did not bleed out the air from the slave cylinder.

Jul 10, 2009 | Ford Ranger Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

205 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...