Question about Chevrolet 1500

1 Answer

Cant get the old bearing on the front passenger side off

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 87 Answers

It might me not in use

Posted on Aug 03, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

ES Lancer - vibration, dull grinding noise when turning right, even at low speeds. Intensifies as I approach 30+mph. Replaced CV Axle, Tie Rod End, Bearing, and Hub. No dice.


Turning right and having a loader noise, means the left/drivers side is bad. Turn right, more pressure on the left side. and vice versa.

Aug 09, 2015 | 2003 Mitsubishi Lancer

1 Answer

Cranksensorlocation


On the 6 cylinder it is located on the left side of the engine when look at it not far from the number one cylinder. in line with the bearings and seals on serpentine belt side next to fire wall about 10 o'clock while facing engine standing at passenger side front wheel.O7OUT

Mar 08, 2014 | 1988 Chevrolet Celebrity

1 Answer

Right front wheel bearing hub cant loosen the half shaft nut


have a helper push on brake firmly and use a breaker bar. or break loose with wheel bolted on and car on the ground, in park.

Feb 16, 2013 | 1990 Cadillac Deville

1 Answer

I have 89 old 88 delta. When driving it sounds like a real high humming noise from the passenger front end, when the weight is shifted to the drivers side it seems to go away until weight is put back on...


Wheel bearing. Sounds like the right front, but have the mechanic verify it first. A lot of bearings have been replaced for the opposite side that they thought was bad.

Dec 10, 2010 | 1989 Oldsmobile Delta 88

1 Answer

I have the caliper and rotor off.Can not get the hub off to get to the bearing.It is on the passenger side front.


You did not mention the year and model. If it is 2001 or back the front wheel bearings are pressed in the knuckle. to replace you have to remove the knuckle. press out the old one and press in the new one

Sep 16, 2010 | Saturn LW Cars & Trucks

3 Answers

How to change my front differential seal and bearing ? passenger side. I bought a new wheel bearing because of a humming sound on passenger side and doing so saw leaking seal and maybe the humming was...


That will be a Huge job. The whole front diff must come out of the car and the case will need to be taken apart to even gain acess to the carrier side bearings.
The hub bearing is where the wheel bolts up is that maybe what you are talking about?
Also the axle seal isn't that bad to do you need to remove the cv shaft then it's just a simple remove the seal and install the new one.
But all of these jobs will be big ones.

Oct 13, 2009 | 1999 GMC Jimmy

1 Answer

How big of a job in replaceing laft front wheel


At first I also thought it'd be hard to do, but I tried myself with a helping hands from an old friend. Roughly less than 2 hr, if you don't have right tool, bearing press, to drive the old bearing out from and new one into the wheel knuckle, you definitely need helping hands to do that job.

Jun 10, 2009 | 2004 Chevrolet Aveo

1 Answer

2001 daewoo lanos front passenger bearing


Remove the wheel ,then track end ,brake caliper support ,the pinch bolt that holds housing to the strut ,lower track control arm swivel.pull off and place on bench .knock the centre hub piece out and on the inside of the housing is a big circlip that holds it in .Then take to a garage and have the old one pressed out and the new one pressed in.stripping shouldnt take more than 35mins ,visit to garage for the pressing?? allow 2 days --- refitting max half hour

Mar 18, 2009 | 2001 Daewoo Lanos

1 Answer

How to replace front wheel bearing on 1996 saturn sl1, passenger side


should b 3 15mm bolts on the bac side and 1 axel nut hammer on the old bearing it should come out it might have an abs plug

Mar 02, 2009 | 1996 Saturn SC

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...