Question about 1999 Lincoln Town Car

1 Answer

Is there a set screw that holds lower ball joint

Posted by on

1 Answer

I didn't find one, came out w/ a fork seperator...

Posted on Oct 06, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I get pressure off the torsion bar in order to pull the lower ball joint arm


How to Replace a Lower Ball Joint (short, quick version ...

? 9:27
https://www.youtube.com/watch?v=E9O_cOB2MTI
May 27, 2014 - Uploaded by ChrisFix
Replacing a Lower Control Arm Ball Joint. Learn how to replace alower ball joint by pressing it out of the ...

Popular Mechanics - May 1975 - Page 164 - Google Books Result

https://books.google.com/books?id=auIDAAAAMBAJ
Vol. 143, No. 5 - ‚ÄéMagazine
I enclose check money order for $4.49 postpaid for each set ordered. ... Conversely, with a tension-loaded ball joint, force on the joint works to pull fast ball joints by taking pressure off primary load-carrier, here the lower ball joint of a torsion-barsuspension system. ... 1 shows the coil spring on top of the lower control arm.

Torsion bar removal - Ford F150 Forum - FordF150.net



Dec 13, 2015 | Cars & Trucks

1 Answer

How to replace a lower ball joint on 2004 mercury mountaineer?


Remove the brake caliper by removing the two bolts that connect it to the steering knuckle. Remove the lower ball joint cotter pin and retaining nut. Pry the steering knuckle up and away from the lower ball joint. Unscrew the grease fitting from the bottom of the lower control arm. Press the lower ball joint out of the control arm using a ball joint remover set.
Press the lower ball joint into the control arm using a ball joint installation tool. Remove the block of wood supporting the upper control arm. Install a new cotter pin through the ball joint stud.Install the grease fitting on the bottom of the ball joint. Use a c-clamp to push the piston back into the brake caliper. Reinstall the wheel assembly. Here you can find the quality parts http://www.buyautoparts.com/steering_system.htm

Aug 29, 2011 | Mercury Mountaineer Cars & Trucks

1 Answer

Need pictures and procedure 91 Ford pickup F250 twin I beam ball joint replacement.


Wheel Spindle, F-150, F-250, F-350
Removal
  1. Raise the front of the vehicle and install safety stands.
  1. Remove the wheel and tire assembly. Refer to Section 04-04 .
  1. Remove the disc brake caliper (2B120) from the rotor and wire it out of the way. Refer to Section 06-03 .
  1. Remove the dust cap, cotter pin, nut retainer, nut, washer and front wheel bearing (1216).
  1. Remove the rotor from the front wheel spindle (3105).





    Item Part Number Description 1 606085 Clamp Bolt 2 3B404 Camber Adjuster 3 800895 Nut 4 800937 Nut 5 3049 Front Suspension Upper Ball Joint 6 3050 Front Suspension Lower Arm Ball Joint 7 3105 Front Wheel Spindle 8 642569 Cotter Pin 9 3304 Steering Sector Shaft Arm Drag Link 10 383489 Nut 11 3001 Front Axle Assembly 12 388727 Bolt A - Tighten to 77-103 Nm
    (57-75 Lb-Ft) B - Tighten to 68-92 Nm
    (50-67 Lb-Ft) C - Tighten to 113-153 Nm (83-112 Lb-Ft) D - Tighten to 340-460 Nm (250-339 Lb-Ft)
  1. Remove bearing cone and roller (1201) and wheel hub grease seal (1190). Discard the seal.
  1. Remove front disc brake rotor shield (2K004). Refer to Section 06-03 .
  1. Disconnect the steering linkage from the integral front wheel spindle and spindle arm by removing the cotter pin and nut and then removing the front wheel spindle tie rod from the spindle arm with Tie Rod End Remover TOOL-3290-D or equivalent.
  1. Remove the cotter pin and castellated nut from the lower ball joint stud.
  1. Remove the nut from the axle clamp bolt and remove the bolt from the axle.
  1. Remove the camber adjuster from the upper ball joint stud and axle beam. If required, use Ball Joint Removing Tool D81T-3010-B or equivalent to remove adjuster.
  1. stj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not use a pickle fork to separate the ball joint from the axle as this will damage the seal and the ball joint socket.
    Strike the inside area of the axle as shown to pop lower ball joints loose from the axle beam.
  1. Remove the front wheel spindle and ball joint from the axle.






Ball Joint, F-150, F-250, F-350 SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number U-Joint Tool T74P-4635-C Ball Joint Remover T94T-3010-AH
Removal
  1. Remove the front wheel spindle (3105) and ball joint assembly from the axle. Refer to Wheel Spindle, F-150, F-250, F-350 in the Removal and Installation portion of this section.
  1. NOTE: Lower ball joint must be removed first.

    Install the front wheel spindle in a vise and remove the snap ring from the lower ball joint.
  1. Remove the lower ball joint from the front wheel spindle using U-Joint Tool T74P-4635-C and Receiver Cup D81T-3010-A5 or equivalent for F-150. Use Ball Joint Remover T94T-3010-AH for F-250 and F-350.
  1. Turn the forcing screw clockwise until the ball joint is removed from the front wheel spindle.
  2. CAUTION: Do not heat the ball joint or the front wheel spindle to aid in removal.
    Assemble U-joint tool and cup on the upper ball joint, and turn forcing screw clockwise until ball joint is removed from the front wheel spindle.


    Installation
    1. stj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not heat the ball joint or axle to aid in installation.
      NOTE: Upper ball joint must be installed into the front wheel spindle first.

      NOTE: Individual ball joint tools are included in Ball Joint Adapter Set D81T-3010-A or equivalent.

      To install the upper ball joint, assemble C-frame assembly, Ball Joint Receiver Cup D81T-3010-A5 and Installation Cup D81T-3010-A1 and D81T-3010-A3 or equivalents inside cup D81T-3010-A4 or equivalent in position on the front wheel spindle.
    1. Turn forcing screw clockwise until ball joint is seated.



    2. snorkelbobby_49.gif

Mar 25, 2011 | Ford F-250 Cars & Trucks

1 Answer

Ball joint repair and how do you do it


To perform the following procedure, the lower control arm must be removed from the vehicle. Refer to Removal And Installation for that procedure.

  1. Using a screw driver or other suitable tool, pry the seal boot off of the ball joint assembly
  2. Position receiving cup, Special Tool 6758 to support lower control arm when removing ball joint assembly. Install Remover, Special Tool 6919 on the top of the ball joint assembly.
  3. Using the arbor press, press the ball joint assembly completely out of the lower control arm.

NOTE: When installing ball joint in lower control arm, position the ball joint in control arm so notch in ball joint stud is in the direction shown. This will ease assembly of the ball joint to the steering when installing pinch bolt.

  1. By hand, position ball joint into ball joint bore of lower control arm. Be sure ball joint is not cocked in the bore of the control arm, this will cause the ball joint to bind when being pressed into control arm.

 

  1. Position control arm with installed ball joint, in an arbor press with Receiving Cup, Special Tool 6758 supporting the lower control arm. Then center Installer, Special Tool 6908-4 on the bottom of the ball joint
  2. Carefully align all pieces. Then press the ball joint into the lower control arm until it is completely seated against surface of lower control arm. The ball joint is correctly installed when there is no gap between the ball joint and the lower control arm. Do not apply excessive force against the ball joint or the lower control arm.
  3. Install a NEW seal boot by hand as far as possible on the ball joint. Installation of the seal boot is to be with the shield positioned as shown.

CAUTION: Do not use an arbor press to install the sealing boot on the ball joint. Damage to the sealing boot will occur if excessive pressure is applied to the sealing boot when it is being installed.

  1. Place Installer, Special Tool 6758 over seal boot and squarely align it with bottom edge of seal boot. Apply hand pressure to Special Tool 6758 until seal boot is pressed squarely against top surface of lower control arm.

CAUTION: A replacement ball joint is not pre-lubricated. Properly lubricate the replacement ball joint using Mopar Multi-Mile grease or an equivalent. Lubricate ball joint after seal boot is installed but prior to top of seal boot being pushed down below notch in ball joint stud. Air must vent out of the seal boot at notch when grease is pumped into ball joint, failure to do so will balloon and damage seal boot. Do not over grease the ball joint, this will prevent the seal boot from pushing down on the stud of the ball joint.

CAUTION: After the ball joint is properly greased, clip the end of the grease fleeing off below the hex. The ball joint seal boot is non-purgeable and further greasing is not required and can result in damage to the seal boot.

  1. Reinstall lower control arm on vehicle.

Mar 07, 2011 | 2000 Dodge Caravan

1 Answer

I have a 97 thunderbird V8. I bought the ball joint for it but i need to know how to replace it myself. It is the lower ball joint on the passenger side.


Hi, to make the process much more simple you will need to rent, buy, barrow a ball joint press. this tool set will make the job 10 times easier. you can rent these sets from advance auto parts and return them to get all of your money back, its pretty nifty. with the tool you will be able to press the ball joint out and back in. first and foremost put the cars subframe on a jackstand so the car doesnt fall on you in the middle of the job. next remove the cotter pin out of the ball joint and tie rod nuts. then remove the tie rod end nut and remove the tie rod from the spindle, then remove the ball joint nut and separate the lower control arm by prying the control arm down, then use a bungee cord to hold the strut/spindle out of the way, then use the ball joint tool to remove and replace the ball joint. Putting it back together is just the reverse of taking it apart.

May 19, 2010 | 1997 Ford Thunderbird LX

2 Answers

What is the estimated cost to replace the ball joints on a 2001 Land Rover Discovery SE (91k mi.)?


HI. Ok, This vehicle is equipped with an upper and lower set of ball joints. The prices are as follows:

Parts price will be $40.00 for the upper set
The labor is set to $195.00 for the upper replacement procedure.

Parts price for the lower ball set will be $40.00.
The labor price for the lower replacement procedure will be $165.00

NOTE_ Land Rover recommends to replace the upper and lower, in this situation. Total cost, if you chose to replace the upper and lower ball sets, will be $80.00 for the parts, and $360.00 on the labor.

Jan 14, 2010 | Land Rover Discovery Cars & Trucks

1 Answer

How do i change the ball joints


You have to seperate the lower ball joint from the steering knuckle and cut out the rivets holding the ball joint to the lower "A" arm slid out the old ball joint and bolt in the new one bolts should come with the replacement ball joints I hope this helps.

Sep 24, 2009 | 1990 Buick Skylark

2 Answers

How do i renew lower balljont


to remove a ball joint from a peugoet 106 is a nightmare.
you have to remove the complete wishbone then iether hammer it out of preffrably use a hydralic press.

-loosen wheel bolts.
-jack the car up (safely on axel stands)
-remove wheel.
-then thier is 2x m8 set screws which hold on the anti role bar bush
-then remove the single bolt which clamps the ball joint to the wheel hub, (completely remove it as it is in a channel of the ball joint)
-remove the bolt on the other side of the wishbone.

now for the hard bit, the final two bolts. theese you get access from inside the car.
-remove the rubber door seals. just give them a yank.
-pull off the steel clips which hold the carpet down
-then another handfull of plastic clips from the top of the footwell and the carpet should peel back. two reveel 2x m10 nuts. when these are removed the wish bone will drop to the floor.
(maybe with a tad of persuation from the ball joint to hub)

when the wish bone is removed you have two options. you can try and get it out yourself or take it to a garage and let them use the hydralic press.

as it is pressed in the best bet for removing it with out damage to the wishbone, find two large sockets one shich is larger then the ball join which the wishbone will sit on, and one socket that is smaller then the ball joint which you can place ontop of the ball joint, then get a decent size hammer. even a slegde, and give it a dap.

best of luck mate.

Apr 29, 2009 | Peugeot 405 Cars & Trucks

1 Answer

Replace ball joints


Remove in this order: wheel, loosen the 4 lower ball joint set bolts, cotter pin and nut from tie rod, tie rod from ball joint bracket, ball joint from lower control arm, 4 lower ball joint set bolts, ball joint from suspension. Install is reverse but don't tighten the 4 lower ball joint set bolts.

torque is as follows:
ball joint to control arm- 112 ft-lbs
Tie rod nut- 67 ft-lbs
lower ball joint set bolts- 83 ft-lbs
remember to use a new cotter pin

Oct 08, 2008 | 2004 Toyota Tacoma

Not finding what you are looking for?
1999 Lincoln Town Car Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Fordexpert

Level 3 Expert

5331 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...