Question about Chevrolet TrailBlazer

1 Answer

Clutch slave cylinder leaking inside cab on clutch pedal and floor

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 127 Answers

Clutch cylinder,, The slave cylinder is located on the transmission. The make a repair kit for most models or you can buy a new one

Posted on Mar 24, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

1988 chevy k2500 clutch pedal has no resistance

Your truck has a hydraulic clutch release system, you have a problem in it due to a leak in the slave or the master cylinder, The slave cylinder which is the one that leaks most often is inside the bell housing and it requires the ****** be removed to replace it.

Aug 09, 2012 | Cars & Trucks

2 Answers

What could cause a clutch pedal in a 1996 honda accord to lost pressure

no fluid in the clutch reservoir due to a failed clutch slave cylinder
time to replace both the clutch slave and master cylinder

Dec 02, 2017 | 1996 Honda Accord

1 Answer

I have a 1992 chevy pickup and the manual clutch will not engage. The clutch pedal goes to the floor, and will come back up. The clutch assembly only has about 15000 miles on it.

not sure on that model if it is cabel check conectoins posible broken cable,,but i think it was hydrolic ,causes could master cylinder on firewall internal leak check fluid can leak inside under dash,also check slave cylinder for leak or burst,leaking hose or pipe,but first check fluit level on top of master cylinder

Aug 06, 2011 | 1983 Nissan King Cab

2 Answers

Ford courier1995 Ford Courier clutch will not disengage... clutch pedal easily floored with no ability to engage first gear.

the automatic clutch adjuster mechanism at the top of the pedal inside the cab is my first suspect before the clutch itself

May 03, 2011 | 1995 Ford Bronco

1 Answer

You said it the slave cylinder was leaking to replace it how can i tell if its bad if its not leaking

usually when you have a bad clutch slave cylinder you know it right away because since it is a hydraulic part, once a seal inside the slave cylinder gets bad, it will start leaking fluid, at the same time, because the seal is not sealing properly, it will allow air inside the system causing your clutch pedal to feel soft and spongy.
When a clutch pedal feels that way, its an indication of air in the system and when this happens it makes it hard to operate the clutch properly because it engages even with your foot almost all the way to the floor. at times you may not even be able to place your car or truck in gear due to this problem.
A bad clutch master cylinder will have similar symptoms, make sure that you look closely at each one of these items to determine which one is the problem (the one malfunctioning will be the one leaking fluid)
One check you can do on the master cylinder is to depress the clutch pedal while someone watches the brake fluid reservoir level. if the level rises while the clutch pedal is being depressed than the clutch master cylinder is bad and should be rebuilt or replaced.

Jan 07, 2011 | Ford Explorer Cars & Trucks

1 Answer

2007 Jeep Compass - Clutch pedal went to the floor on my daughter --fluid is low -no visable external leaks - clutch does not slip Do I need to split the flywheel housing in order to change the slave...

Usually if you pump the pedal a lot when it's cold if the slave is leaking you will see some dripping from the bellhousing. I would definitely check inside the cab where the master attaches to the pedal rod to be sure it isn't leaking there and that's why you don't see fluid outside though. If you already checked there then yes if the slave is leaking, that's the only way in there.

Oct 03, 2010 | 2007 Jeep Compass Limited

2 Answers


Need to have it check could be clutch master cylinder or slave cylinder or hose from clutch master cylinder to slave cylinder.check brake fluid at clutch master cylinder sit next to brake master cylinder if empty could have a leak. fill and pump peddle and look for leak.

Jan 12, 2010 | 2001 Ford Focus

2 Answers

Clutch pedal going to the floor too easily..

You likely have a leak in either the master for the clutch, the line going to the slave unit or the slave itself. You need to look at these items and replace any leaking components. If the master is full, likely it is internally bypassing and therefore needs replacement. Air in the system can only get in there from a leak. bleeding may make it work for a short time but is not a cure. After making any repairs you do need to bleed it though. (just like brakes)

Oct 23, 2009 | 2004 Nissan Maxima

2 Answers

Clutch pedal stuck to the floor stick shifter will not go into gear while truk is running

try pulling pedal up, does it drop str8 to the floor,if yes problem in hydralic clutch like clutch master cylinder or slave cylinder,if pdel stays up appears to be ok then the clutch may need replacing

Mar 06, 2009 | 1995 Ford F150 Styleside Regular Cab

1 Answer

No clutch on the Chevy 3500 Pickup after successfully changing the starter.

If it had 2 bolt studs with nut on the other end ando line going to the top of the transmission it is the slave cylinder and you have to line the rod inside to the fork inside the bellhousing if this is on the bleed the clutch cylinder and the pedal should return to normal. Be sure to check for leaks in this line even a little leak can cause you not to have a clutch pedal. Also check inside the cab behind the clutch pedal where the rod comes through the firewall and make sure it is not leaking. If the fluid is low be sure to fill it with DOT 3 brake fluid.

Jan 11, 2009 | 1993 Chevrolet C3500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides