Question about Ford F-350

1 Answer

Im installing a ecm in my 94 ford truck how do i program it

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 90 Answers

Should be progrmmed already,

Posted on Mar 24, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where can I get a 1992, 93, 94 ECM connector pin out diagram thats not expensive or is free /

Hi, Go to a wrecking yard they maybe able to help you. You also could get it free. Good luck.

Jun 14, 2016 | Ford Cars & Trucks

2 Answers

I switched a 2.5 98 ford ranger motor over to a 2.3 94 ford ranger motor it will crank but won't start

did you also switch out the ecm seems I had to on mine when I did similar.

May 06, 2015 | Ford Cars & Trucks

1 Answer

I have a 99 ford f250 sd with a v10 drove truck home parked it next morning crank but no start. had a shop check it out said crank sensor changed nothing then cam sensor changed nothing. has great...

put back old ecm and try spare key. if it does not work and you use a new ecm you need to program your keys to the immobilizer for it to work

Mar 21, 2015 | Ford F-250 Cars & Trucks

1 Answer

Is a 94 esm the only year i can use in my 94 cavalier

if you mean ecm(computer) there is a number on a tag on the ecm that will have to match and then there is a chip that will have to be transferred from the original ecm to the ecm your installling in your car.have you had the car put on a scan tool as if the ecm is bad it should have set a code for the ecm,if you have spark and fuel you should be at least getting an indication the car is trying to start,short start up,back fire through intake or could have a timing problem or even a problem with the ignition module not working properly,this needs to be properly checked out before throwing parts at it.

Mar 29, 2012 | 1994 Chevrolet Cavalier

2 Answers

Installed a new ecm flashed and now the engine wont crank

you have to reprogram the keys and reset the parameters

Aug 12, 2010 | 2000 Ford Focus

1 Answer

Where is the location of the ECM on a 1998 ford explorer?

ECM (Engine Control Module) is the old name to the new PCM
(Powertrain Control Module) denomination; this unit performs many functions on your car. The module accepts information from various engine sensors and computes the required fuel flow rate necessary to maintain the correct amount of air/fuel ratio throughout the entire engine operational range.

Based on the information that is received and programmed into the PCM's memory, the PCM generates output signals to control relays, actuators and solenoids.

The module is mounted under the hood on the firewall. On 493-94 models, it is mounted low on the firewall, near the left-hand fender (drivers side). On 495-99 models, it is mounted high on the firewall offset to the right-hand side of center.


Exploded view of the firewall PCM mounting for 493-94 models


Exploded view of the firewall PCM mounting for 495-99 models

  1. Disconnect the negative battery cable.
  2. Disengage the wiring harness connector from the PCM by loosening the connector retaining bolt, then pulling the connector from the module.
  3. Remove the two nuts and the PCM cover.
  4. Remove the PCM from the bracket by pulling the unit outward.
To install:
  1. Install the PCM in the mounting bracket.
  2. Install the PCM cover and tighten the two nuts.
  3. Attach the wiring harness connector to the module, then tighten the connector retaining bolt.
  4. Connect the negative battery cable.

Hope helps (remember comment and rated this).

Jul 31, 2010 | 1998 Ford Explorer

1 Answer

Putting cd player in 94 explorer?? HELP PLEASE?!?!?!?

Yes, that would be fine, make sure you solder the wires and tape well or use shrink tube on the connections.

Mar 13, 2010 | 1994 Ford Explorer Limited

1 Answer

Just change the ecm on my 2001 ford Windstar and it won't start the anti theft light is blinking

did you get the ecm flash programmed? newer vehicles require the ecm to be flash programmed before they are installed your dealer and some auto parts stores can do this for you it usually runs around $90.

Mar 20, 2009 | 1998 Ford Windstar

1 Answer

Vacuum diagram 94 ford escort lx

check the vacuum diagram located under the hood this should rovide you with what you need.

Dec 19, 2008 | 1996 Ford Escort 4 Door

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides