Question about 2000 Dodge Caravan

2 Answers

I have a 2000 dodhe caravan..the signals arent working..we changed the bulbs like 5 times already and nothing seems to work...what is the problem?

Posted by on

  • kelliehobson Mar 24, 2011

    the hazards work properly..there is no clicking when i try to turn the signals on..replaced the bulbs and still nothing

  • kelliehobson Mar 25, 2011

    i have gone to a few parts place and they told me that i have to go to Chrysler directly since they dont have that part in stock..but htank you for your advise and i will definately get that checked

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 4,977 Answers

Have you checked the fuses in the fuse panel under the dash drivers side.are all the signal bulbs not working front and back.do you hear the signal flasher clicking.do the hazards lights work.if the hazard lights work then you can see if all the lights work front and back,if so then it is either a fuse for the turn signals or the signal flasher.to see what the flasher looks like,with the hazards on you can locate it to see what the signal flasher looks like,as the signals have their own flasher.it is usually on the fuse panel or behind the dash.

Posted on Mar 23, 2011

  • 1 more comment 
  • kelliehobson Mar 24, 2011

    hazards work properly...changed bulb and no clcking what so ever..tried a parts source and they dont carry it..what else can i do..will this be expensive?

  • kelliehobson Mar 24, 2011

    its keeps shorting out...when we put a new bulb in..worksfor a few minutes then its out..can there be a shortage?

  • robert wales Mar 24, 2011

    the problem you have is not bulbs,you have a signal flasher problem that needs to be replaced,as indicated in my first answer if the checks were okay.the signal flasher gets heated enough that it starts to work then quits.

×

Ad
  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer got voted for 20 times.

  • Contributor
  • 299 Answers

When u press the hazards do they flash? let me know if not its the blinker relay.

Posted on Mar 23, 2011

  • 1 more comment 
  • kelliehobson Mar 23, 2011

    no the hazards do not flash

  • prostreet 55
    prostreet 55 Mar 24, 2011

    its the flasher relay look on the fuse box or under the dash, go to parts store and ask for new one so u can see what it looks like so it will be easier to find.

  • prostreet 55
    prostreet 55 Mar 24, 2011

    okay so now the hazards are working so now u have to find the turn signal relay which gives u that clicking sound when signal is engaged , it can be square or round have parts store look it up for u so u can identify part

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The turn signals in my 2000 dodge caravan work erratically, some times good for weeks, other times good only for 2 minutes.The hazard signal works fine. What can I do to correct this problem?


It could be several things, since it is all the turn signals, not just one side or the other it narrows down possibilities. Your relay may be dying. You can swap a relay with another already in the box. Just switch one beside it from another plug(verify the numbers are the same. ) If this isn't the problem, then go for the the controller; replace your turn signal control. It is fairly easy to replace and not more than about $50.00.

Oct 03, 2014 | 2000 Dodge Caravan

1 Answer

High beams arent working


Sounds like the high beam switch is bad. It is located in conjunction with your turn signal.

Oct 19, 2013 | 2000 Ford Explorer

1 Answer

The temperature, speed, and gas guages arent working on my 2000 Dodge Caravan 4 cylinder. The milage only lights up for a few seconds then goes out. My Dash lights work though. Also when this happens my...


G'day mate it would seem that the fuses though on inspection are fine they may be not so good if removed for inspection also remember that if the fuses are dirty that moisture will carry a voltage to earth on a dirty damp circut. also there should be another fuse box near the battery with higher amperage fuses hope this helps

Apr 03, 2010 | 2000 Dodge Caravan

3 Answers

Left brake light will not come on, I replaced the switch under the brake pedal and still nothing, can you assist


check bulb and voltage signal to that particular lamp assembly/connector...socket should have 12v signal and other should have good path to ground....

Sep 27, 2009 | 2000 Dodge Caravan

1 Answer

Fronty signal and air bag problem


check for loose connection.

Aug 11, 2009 | 2000 Dodge Caravan

2 Answers

My brake lights arent working!


Normally you'll find a brake switch at arm of brake pedal, up under dash. Switch should have 12v going in one side, when pedal not pushed, and both sides when pedal is pushed.

Jun 03, 2009 | 2007 Kia Rio 5 Sx M/T Hatchback

1 Answer

2000 dodge caravan rear passenger blinker not working


CHANGE THE SOCKET FOR THE BULB THATS FAILED ALSO CHECK THE TAIL LAMP ASSY, THE CONECTOR ON THE LAMP MAY BE DISTORTED AND NO CONTACT TO THE SOCKET.

Dec 30, 2008 | 2000 Dodge Caravan

1 Answer

Rear passenger flasher not flashing for signal or hazards, replaced the bulb and still nothing. The light works but does not flash. 2000 dodge Caravan


This is An Isolated Problem Probably with a Single GROUND that is located somewhere at rear on underbody

Dec 30, 2008 | 2000 Dodge Caravan

1 Answer

Side signal driver side


What your describing sounds like incorrect bulb positioning. If the socket is not located correctly then water can enter the light housing and blow the bulb, sometimes in pieces. This is the only condition that a bulb blows to pieces, when a hot bulb meets water. If needed remove the entire lamp assembly to make sure it is properly located in the socket. Good luck.

Oct 16, 2008 | 2000 Dodge Caravan

1 Answer

Electrical


No. I have a Caravan 2000. I can tell you that I have had to change the fan motor relay twice and it has worked ever since. As for the windows, let me guess... It goes down a little at a time, and then back up a little at a time as if it needs to cool off after 1inch or work? If so, your motor is busted. Not related to the fan!

Rear window wiper same thing! Nothing is related, they are only common problems on Caravans that somewhat happen after any given amount of time.

Jul 27, 2008 | 2000 Dodge Caravan

Not finding what you are looking for?
2000 Dodge Caravan Logo

448 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75842 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...