Question about 1994 Oldsmobile Cutlass Supreme

1 Answer

How to replace a starter on a 94' cutlass - 1994 Oldsmobile Cutlass Supreme

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Oldsmobile Master
  • 17,970 Answers

3.1L Engines - 1988-94 VEHICLES
(see Figures 5, 6, 7 and 8)

  1. Remove the air cleaner and duct assembly.
  2. Disconnect the negative battery cable.
  3. Raise and safely support the vehicle.
  4. If equipped with an engine oil cooler, drain the engine oil, remove the oil filter and position the hose next to the starter motor to the side.
  5. Remove the nut from the brace at the air conditioning compressor, nut from the brace at the engine and the brace.
  6. Unfasten the retaining bolts, then remove the flywheel inspection cover.
How to replace a starter on a 94' cutlass - zjlimited_919.jpg

Fig. 5: Unfasten the retaining bolts ...

zjlimited_920.jpg

Fig. 6: ... then remove the flywheel cover

  1. Remove the starter bolts and shims, if equipped. Do not let the starter hang from the starter wires.
  2. zjlimited_921.jpg



    Fig. 7: An extension may be How to replace a starter on a 94' cutlass - zjlimited_922.jpgthe starter mounting bolts

    zjlimited_922.jpg

    Fig. 8: Remove the starter motor and any shims that may have been used

    1. Detach the starter wires from the solenoid, then remove the starter from the vehicle.
    To install:
    1. While supporting the starter, connect the starter wires at the solenoid.
    2. Install the starter motor-to-engine mount with the shims, if equipped, and the mounting bolts. Tighten the bolts to 32 ft. lbs. (43 Nm).
    3. If equipped with an engine oil cooler, reposition the hose next to the starter motor, install the oil filter and refill the engine with the proper amount of engine oil.
    4. Install the flywheel inspection cover and tighten the bolts.
    5. Install the starter support brace to the air conditioning compressor and tighten the nut to 23 ft. lbs. (31 Nm).
    6. Carefully lower the vehicle, then connect the negative battery cable.
    7. Install the air cleaner and duct assembly.

    Hope helps.

Posted on Mar 23, 2011

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: Need to Replace my starter.

Before taking your starter motor off take a note of the make and model number and that the replacement matches it exactly, there is nothing worse to find that half way through a job that the replacement is critically different in some way. Disconnect the negative cable to the battery. Unbolt the cables to the starter solenoid and starter motor assembly. Remove the two mounting bolts and drop the motor assembly out. Reverse the above steps when installing the new motor. Sorry that this is not a more complicated procedure but swapping the starter motor for a new one is one of the simpler jobs. Take your time and keep safe and you should be able to complete everything in about an hour. Remember to reconnect the battery. Good luck

Posted on Dec 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 94 olds cutlass ciera. I have replaced the battery, new cables, altenator, starter, and I have a re-current problem of turning the ignition and I get a click, and then finally it starts.


The click is the solenoid not getting enough power to energise the starter and engage the pinion gear. Either the battery is weak or the connections going in the starter circuit have excessive resistance and need to be tightened/cleaned.

Feb 24, 2017 | 1994 Oldsmobile Cutlass Ciera

2 Answers

Do you know where the 2 bolts are on a starter for a 94 olds cutlass ciera s?


REMOVE THE STARTER FLY WHEEL COVER. STARTER BOLTS IS VERTICAL BOLTED INTO THE ENGINE.

Jul 08, 2011 | 1994 Oldsmobile Cutlass Ciera

1 Answer

Need to Replace my starter. Can i get a step by step crash course? 94' Cutlass Ciera


Before taking your starter motor off take a note of the make and model number and that the replacement matches it exactly, there is nothing worse to find that half way through a job that the replacement is critically different in some way. Disconnect the negative cable to the battery. Unbolt the cables to the starter solenoid and starter motor assembly. Remove the two mounting bolts and drop the motor assembly out. Reverse the above steps when installing the new motor. Sorry that this is not a more complicated procedure but swapping the starter motor for a new one is one of the simpler jobs. Take your time and keep safe and you should be able to complete everything in about an hour. Remember to reconnect the battery. Good luck

Dec 02, 2010 | 1994 Oldsmobile Cutlass Ciera

3 Answers

Turn ignition and nothing. Replaced starter, had battery checked and no issuse there, all fuses are good. Can this be in the ignition switch on the column or waht about the module under distrbutor cap?


my 94 cutlass convertable i turn the key my cd player work lights windows everything but when i go to start it the security like blinks it want start ? is it my key

Mar 15, 2010 | 1994 Oldsmobile Cutlass Supreme

1 Answer

Where is the starter relay switch on a 94 cutlass supreme?


should be under hood near firewall or in one of the fuse box panels

Oct 26, 2009 | 1994 Oldsmobile Cutlass Supreme

1 Answer

94 cutlass supreme wont start


It sounds a Lot like you have some Trash inside the Fuel Tank .Also, Check the Fuel Filter and Starter.

Jan 15, 2009 | 1994 Oldsmobile Cutlass Supreme

1 Answer

94 olds cutlass ciara


it is probably just the two smallest connectoers on the starter solenoid are crossed. one is to supply power to activate the starter, and the other supplies full 12 volt power to the ignition while starting. if crossed, the wire to the ignition will supply power to try and activate the starter.

Oct 07, 2008 | 1994 Oldsmobile Cutlass

1 Answer

Cutlass supreme wont start


It could possibly be the starter, but before you get that far make sure the Battery cables are connected very tight. If loose the car won't start or do anything. Also make sure the battery cable is grounded.

Sep 24, 2008 | 1994 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
1994 Oldsmobile Cutlass Supreme Logo

1,271 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...