Question about 1999 Chrysler Town & Country

1 Answer

Parking lamps My dear brother did me the favor of power washing my engine, I could kill him! problem the left side tail light and front marker lights don't work and the battery won't stay up over night. put the computer on it and the battery and alt. are fine. today i inspected the terminal connection under the battery wires were dirty no breaks, and all connection inside are clean and undamaged. have check all fuses and bulbs. any ideas of how to locate the problem

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 335 Answers

Check the Bulkhead connector between the engine compartment and the passenger compartment I have seen wather get in there and cause pure hell. Also maybe the fuse block has water in it seen that too.
if this information is helpful please give me a good rating Thank you, Randy

www.aceautomotive1.com

Posted on Aug 15, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

04 Nissan maxima tail lghts don't always come on right away thought maybe headlight switch not sure need help


Download 2004 Nissan Maxima Lighting System Section LT PDF Manual 190 Pages Do you know how to do electrical testing with volt ohm meter ? Do you know what a BCM is ? COMPUTER !
Control of the parking, license plate, and tail lamp operation is dependent upon the position of the lighting switch (combination switch). When the lighting switch is placed in the 1ST position, the BCM (body control module) receives input signal requesting the parking, license plate, side marker and tail lamps to illuminate. This input signal is communicated to the IPDM E/R (intelligent power distribution module engine room) across the CAN communication lines. The CPU (central processing unit) of the IPDM E/R controls the tail lamp relay coil. This relay, when energized, directs power to the parking, license plate, rear side marker and tail lamps, which then illuminate.
Testing starts at 134

Feb 05, 2017 | 2004 Nissan Maxima

1 Answer

Were is the fuse under hood located for tail lights for a 2003 chevy tahoe and what amp and or style is the fuse?


Exterior Lamps
The exterior lighting system consist of the following lamps:
• The Headlamps
• The Daytime Running Lamps (DRL)
• Fog Lamps
• The Park, Tail and Marker Lamps
• Exterior Courtesy Lamps
• The Turn Signal/Hazard Lamps
• The Stop Lamps
• The Backup Lamps
• The Clearance Lamps

Park, Tail and Marker Lamps
The park, tail and marker lamps, including the license lamps, are turned on when the headlamp switch is placed in the PARK or HEAD position or anytime the headlights are requested. The underhood fuse block supplies battery positive voltage to both the park lamp relay switch contacts and the park lamp coil circuit. The body control module (BCM) provides a ground or control circuit to the park lamp relay coil circuit. When the park lamps are turned on the BCM energizes the park lamp relay. Current flow is from the park lamp relay to the FR PRK 10 A fuse, RR PRK 10 A fuse, LR PRK 10 A fuse, and the TRL PRK 10 A fuse, and to their respective park and marker lamps. The front park and marker lamps are grounded at G100. The rear park and marker lamps are grounded at G401. The license lamps are grounded at G410. If the headlight switch is left in the ON position, the inadvertent power control feature will turn off the park, tail and marker lamps approximately 10 minutes after the ignition switch is turned to the OFF position. If the driver places the headlight switch in the ON position after the ignition switch has been turned OFF, or if the ignition switch is in the ACCY position, the park, tail and marker lamps will remain on until turned off or the battery runs dead.

Jan 07, 2017 | 2003 Chevrolet Chevrolet Tahoe

1 Answer

I'm needing the wiring diagram for my 2007 Chevrolet Impala LT 3.5 tail lights.


Go to http://www.bbbind.com/free_tsb.html free wiring diagrams ! You having tail light problems ? Do you know how they work ?

They are turned on by the BCM !
Park, Tail, Marker and License Lamps
The park, tail, license, and marker lamps are turned ON when the headlamp switch is placed in either the HEAD or PARK lamp positions, or anytime the automatic light control (ALC) turns the headlamps ON. When the headlamp switch is placed in the park lamp or headlamp positions, ground from G202 is applied through the signal circuit to the BCM indicating the park lamp request. In response to this signal, the BCM applies ground through the park lamp relay control circuit energizing the PARK LP PCB Relay. With the relay energized, battery voltage is applied through the switch side of the relay, both park lamp fuses, and the supply voltage circuits illuminating the park, tail marker, and license lamps. Ground for the left front park and marker lamps is provided at G101 and the right front park and marker lamps at G100. Ground for all rear lamps is provided at G302.
Turn Signal Lamps
The LT T/SIG and RT T/SIG fuses located in the underhood fuse block supplies battery positive voltage to the body control module (BCM) for turn signal and hazard lamp operation. When the turn signal switch is place in either the LEFT or RIGHT position, ground from G202 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. The BCM also sends a message via GMLAN to the instrument panel cluster (IPC) to cycle the turn signal indicator ON and OFF depending on the position of the turn signal switch.
Ground for the turn signal lamps is supplied as follows:
?€¢
G101 provides ground for the left front turn signal lamp


?€¢
G100 provides ground for the right front turn signal lamp


?€¢
G302 provides ground for the left and right rear turn signal lamps

May 03, 2016 | 2007 Chevrolet Chevrolet Impala LT

1 Answer

2000. Where is fuse for tail lights?


Do your headlamps work ?
Park/Marker/License/Tail Lamps
Voltage is applied to the turn/headlamp switch at all times. When the turn/headlamp switch is in the PARK or the HEAD position, voltage is applied to the following components:
?€¢
The park lamps


?€¢
The marker lamps


?€¢
The tail lamps


?€¢
The license lamp

The front marker lamps are grounded through the turn filament of the respective front park/turn lamp. The front marker lamps light as a result.
The automatic lamp control function turns on the park lamps and the headlamps. This action occurs when the ambient light sensor determines that the exterior lamps should be turned ON based on the amount of available light. When the BCM grounds the park lamp relay, voltage is supplied directly to the park lamps, bypassing the turn/headlamp switch assembly. When this action occurs, the following conditions exist:
?€¢
The automatic lamp control relay is grounded.


?€¢
The headlamps turn ON. Refer to Headlights/Daytime Running Lights (DRL) Circuit Description .

The lamps turn OFF when the BCM does not ground the park lamp relay or the automatic lamp control relay. This action is caused by the following conditions:
?€¢
The available light reaches a predetermined level.


?€¢
The ignition switch is turned to the OFF position

Mar 31, 2016 | Pontiac Grand Am Cars & Trucks

1 Answer

Where is the parking light relay located


No relay for the parking lights .
When the headlamp switch is moved to the PARK or ON position, battery voltage is supplied from the 15A Park Lamp fuse to circuit 9. Current flows through circuit 9 to the instrument panel fuse block (IPFB). Battery power passes through the IPFB to both license lamps, both front and rear tail lamps, both front park/turn lamps, and all marker lamps through circuit 9. The front marker and front park/turn lamps are grounded by circuit 150 through the forward lamp ground splice pack. The rear tail lamps and license lamps are grounded by circuit 550 at the rear ground splice pack and the right rear body ground.

Sep 18, 2015 | 2001 Saturn SL

1 Answer

Hello i have a toyota camry 1992 and my passenger side marker wont turn off ???


That's very odd, because the wiring for all of the side markers are just splices from the nearest park lamp wires- the rear tail light in the rear (and the license plate lamps are also splices from these tail lights), and in the front side markers, they are splices from the nearest park lamps. Do all the other park lights work and turn on with the park light switch on? I would examine the 2 wires from that side marker's socket to the wiring harness it goes into-the power wire would somewhere splice into the passenger tail light wire. The other wire would be a ground wire and also splices into a ground wire for the rear end. To be on, the marker lamp would have to be getting power from some live source. I can't imagine where. Does the rear passenger light work correctly?

In that harness to the rear where the park lamps run, there might be a live wire going to an electrical trunk latch switch, or maybe a trunk lamp. If the wires were frayed right beside the side marker wire, you could have some cross feeding of power between the two. Let me know, we always appreciate feedback.

Sep 06, 2015 | Toyota Cars & Trucks

1 Answer

My left side tail light doesn't work after changing the lamp. Jeep 2007 - Commander


it worked before the change out?
there are 3 things that are first. on advance electronics, cars. like this. 2007 is 1st year, of wild complexity.
  1. check fuses first. MIP fuse #8,9,10 (8 is left) check that?
  2. check action of park relay
  3. check for trailer wiring hacks (do you have factory hitch option?)
  4. and scan the PCM , do you see any park fail DTCs'
DTCs are system errors.
that is first.
next if not solved, we look in the FSM for that chapter, and the schematics, to see how its is structured. (varies by year, car)

FSM JEEP XK 2007 (book)
factory service manual.

left side rear tail (park) (tail is old name , car has many park lamps now , not just 1 or 2 tails like in the old days.
so it park and the relay of same name.
there are front parking lights too... do those all work>?

my guess, is you didnt check fuses first.
am i right?
fuse 8 is blown?
but that takes out front left park
and left side marker (park ) lamps too.
so did you look at all left park lights first>?

i bet not, if im wrong then you do have wiring errors.
or the new lamp from china is shorted inside, (common)
try one more lamp , like from GE or Philips.


Feb 24, 2015 | Jeep Cars & Trucks

3 Answers

Why the brake light works and tail light don't work Chevrolet avalanche 2003


they are dual filament bulbs so the tail light filament might have blown and not the stop light , replace the bulb to check

Jul 18, 2014 | 2003 Chevrolet Avalanche

1 Answer

No parking lights in back


parking, yes, tail ,park.
(the correct name is park toy calls them tail, tell me how a tail lamp works in front of car, this name is from 1920cars , that only had 1 or 2 tail lights. (fun history that, with funny names)

if actually park lamps. 1st click of head light? switch?
there are over 20 park lamps in car, inside and out.
side markeres, front park lamps
all dimmable lamps inside are park too. all dead>?
then the park relay is bad (tail/park) or fuse. blown.

Dec 31, 2013 | 2001 Toyota Sienna

Not finding what you are looking for?
1999 Chrysler Town & Country Logo

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

69114 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22026 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...