Question about Chevrolet Equinox

1 Answer

Need to change the drive side tail light bulb. I have removed the two visable screws but will not come apart any suggestions? does it slide out of another screw inside the tire well?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 127 Answers

Check in side trunk for tail assembly removal

Posted on Mar 23, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changing backup bulbs on 2005 buick rendevous


TAIL LAMP ASSEMBLY AND /OR BACKUP, SIDEMARKER, STOP, TURN SIGNAL BULB REPLACEMENT

REMOVAL PROCEDURE

1. Open the liftgate.
2. Remove the screws from the tail amp.
3. Slide the tail lamp rearward in order to disengage it from the retainers on the rear body panel.
4. Disconnect the electrical connector from the tail lamp wiring harness.
5. Remove the tail lamp and side marker lamp sockets from the tail lamp, depressing the locking tab and turning counterclockwise.
6. Remove the bulbs from the tail lamp and the side marker lamp sockets, if replacing the bulbs.

INSTALLATION PROCEDURE

1. Install the bulbs to the tail lamp and side marker lamp sockets, if removed.
2. Install the tail lamp and side marker lamp sockets to the tail lamp, turning clockwise until the locking tab is fully seated.
3. Connect the tail lamp electrical connector to the wiring harness.
4. Position the tail lamp retainer slots to the tabs on the rear body panel.
5. Install the tail lamp to the rear body panel, pressing into place until fully seated.
6. Install the tail lamp screws to the Taillamp.

NOTE: Refer to Fastener Notice in Service Precautions.

Tighten the tail lamp screws to 2 N.m (18 lb in).

7. Close the liftgate.

Apr 16, 2017 | Buick Cars & Trucks

1 Answer

How do I replace a brake light in a land rover freelander 2004 - does the glass cover screw off internally or externally. Are the brake light and tail light bulbs combined? Many Thanks David


If there are visable screws around the tail lite lens yes they come out and just screw off the bulbs socket than the bulb,,,If no visable screws than the should be a panel on in side of vehcle back side that comes out for access to the lights.

Mar 11, 2011 | Land Rover Freelander Cars & Trucks

1 Answer

I need to change the brake and tail light on my 1996 toyota corolla . I would need a manuel on that please.


The steps to replace the brake light bulb on a 1996 Toyota Corolla:

The bulb needed is type 1157. After opening the trunk you need to remove the trunk liner on the side (right side for this example)where the brake light bulb is out. The plastic capture grommets hold the liner in place. Once the grommets are removed there is a nut (10mm) that is a bright brass-like color. This needs to be removed. Then on the outside of the trunk on the tail-light lens left side there are two nuts black in color (10mm) they need to be removed. Now the fun starts .... you needto slide the whole assembly back. You will note two black plastic posts on the rear quarter-panel, do not remove these ... these are used to hold the tail-light assembly in place since on the inside of the tail light assembly there are two rod-like protrusions that slide into these brackets. So.... remove the screws and wiggle the assembly back and it "should" slide back so that you can get at the bulb socket hat you twist to remove from the assembly. Now the bulb is visible and you reverse the order of steps to get it all back together .... a miserable design!

Sep 30, 2010 | Toyota Corolla Cars & Trucks

1 Answer

How do i change the tail light on a 2004 tahoe


Open rear hatch. Remove two mounting screws at the side corner which mount the tail light assy to the body. The whole tail light assy can now be removed. Twist desired bulb holder counterclock wise to remove, then pull bulb to remove. Reinstall in reverse order.

May 19, 2010 | 2004 Chevrolet Tahoe

3 Answers

1995 Toyota Camry tail light. no screws to


To change a bulb on this car you will need to go from the trunk. The bulbs are located behind a small plastic door.

Oct 28, 2009 | 1995 Toyota Camry

2 Answers

I cant figure out how to open the tail light to replace it


open the tailgate- remove the two screws on so that the tail light can slide out. Turn the bulb assemble and remove the bulb. Replace it and slide the lense back in replace the two screws and your done.

Jul 04, 2009 | 2008 Hummer H3

1 Answer

Can't get the right, rear tail light cover off, on my 91' Trooper


The whole lamp comes out and the bulb is change from the back side.

Jun 08, 2009 | 1991 Isuzu Trooper

1 Answer

Need to replace bulb in back up light - do not know how to remove assembly.


yes there are two slide clips in the fender side to keep that side in place

Apr 23, 2009 | 2004 Dodge Dakota

2 Answers

Changing the tail light assembly on a 2004 hyundai santa fe


Made a video of me changing a brake light but I show how to remove and install the tail light assembly. It's also on a 2005 Hyundai Santa Fe but should be the same.

Apr 11, 2009 | 2004 Hyundai Santa Fe

2 Answers

2005 Pacifica Tail light side marker bulb replacement


You have to remove the headlight unit.Detailed instruction in owner manual pg 321-322. If you do not have the manual, it can be downloaded from chrysler web site, owners section.

Dec 18, 2008 | 2005 Chrysler Pacifica

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...