Question about 2001 Hyundai Accent
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: 2001 tahoe door panel
THE COUTESY LAMP IS HOT DUE TO THE DOOR BEING OPEN WHILE THIS PROCEDURE IS DONE!!!! First: Remove the triangle panel at the top of the door (behind the mirror). This is held in with two metal clips about half way down the panel. Do not pry at the bottom as there are two tabs that slide in to keep the module in place. I pulled the top of the triangle out by hand then could see the clips and used a straight screw driver to carefully pry from under the triangle panel so as not to scar the visible part after re-assembly. Once these two clips are disengaged the triangle should pull straight up and be free. Second: Carefully pry out the door lock insert. There are no significant tabs to worry about here. Again a straight screw driver and care should not leave any scars. The lock insert has no mechanical connection but simply is used to slide the lock rod. Re-installing you will need to align the slot for the rod in the lock or unlock position depending on the rod position. Third: Carefully pry out the insert that is located at the door handle. Start at the rear of the insert as this is where the clips are located and once the rear is out pull open the door handle and pull the insert to the rear so as not to break off the two front tabs. You will find two small screws (mine were black). One near the front and one at the rear of the door handle module. Both are 7 mm and are the only ones that need to be remove in the process. (I understand some door panels have an other screw at the very bottom of the door as well; guess you'll have to check you door. Fourth: Pry up the control panel for the automatic windows and unplug the wires. Here again start from the rear and once the rear is free pull the module to the rear and it should come free. There are tabs at the front that you do not want to break off. To unplug the wires - First remove the clips (mine were blue) that hold the plug in place. There is also a push catch on the plug that must be depressed to release the plug from the control panel. Fifth: My door had no push in 'buttons' or clips to hold the door panel in place. It simply lifted up and became free with the exception of the numerous wires attached to things like the speakers, the remote mirrow and courtesy light. Unplug these wires by first taking off any retaining clips (usually blue) and then unplug the wires. The courtesy light pulls straight out (toward the front) and watch your fingers as this is one hot little bulb. The door panel can then be totally removed and set aside. You may find it easier to remove the courtesy light lens by prying out the rear first and then pulling it toward the back of the door so as not to break the two front clips. I found it easier to do this and then install the bulb in the lens and then install the lens back in place. Six: I'm sure I don't need to say it but here goes - ' reverse the procedure to re-assemble'. Remember to poke the courtesy light wire out the hole and re-connect the remote mirror and speaker wires before the door is put in place. The wires to the window and electronic lock module can be installed after the door is back in place. Working by myself made the door difficult to handle during re-installation so I took a 'light' bungy cord and placed some protection over the top of the door and hooked the bungy into the opening were the door handle was to come through. This allowed me to steady the door and do the electrical connections as required. PS - we were replacing the power window motor and were able to 'force' the cable into the gears of the new motor by turning the motor and this saved a lot of further disassembly. The contacts on the new motor were reversed so I removed the pins from the plug going into the motor and reversed them - presto.
Posted on Mar 17, 2009
Firstly, if you don't know how...I doubt you can remove it anyway. Take it to your local car stereo installation shop and ask them NICELY to take it off - explain what the problem is (lemme guess the window/lock doesn't work).
Posted on Jun 15, 2009
SOURCE: Door panel removal
You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door
Posted on Aug 14, 2009
You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. then you just remove the bolts to the mirror
Posted on Aug 14, 2009
On the inside trim, you can remove screws (these screws may be covered by filler pieces or may be visible, or they may require you pry a plastic piece off that covers the screws) that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you need to pull back the weather seal and then you can access the bolts securing the outer handle
Posted on Nov 05, 2009
Tips for a great answer:
Passenger Front Door Module (PDM)
LH Rear Door Module (LRDM)
RH Rear Door Module (RRDM)
Driver Door Switch Assembly (DDSA)
RH Front Power Window Switch
LH Rear Power Window Switch
RH Rear Power Window Switch
LH Front Power Window Motor
RH Front Power Window Motor
LH Rear Power Window Motor
RH Rear Power Window Motor
Class 2 serial data circuit
Power door serial data circuit
PWR WDO 30 Amp Circuit Breaker
DRVMDL Fuse (10 amp)
Driver Door Switch Assembly and Driver Door Module logic, Driver Door Module internal driver operation
PASS MDL Fuse (10 amp)
Front Passenger Door Module logic and internal driver operation
RRDR MDL Fuse (10 amp)
Left Rear Door Module and Right Rear Door Module logic and internal driver operation
Do you know about computer controlled power windows ?
Power Windows Operation
The vehicle is equipped with power windows controlled by the door modules. Each passenger door window can be operated, either from a switch built into the driver door switch assembly (DDSA), or from a switch mounted locally to its associated door. The driver door window can be operated only from the driver door window switch built into the DDSA.
When a window is operated from the DDSA, the DDSA interprets the window switch signal as a specific window switch request and sends the information to the driver door module (DDM) via the power door serial data circuit. The DDM examines the request and checks to see if it has received any class 2 serial data messages from any of the other vehicle modules (i.e. ignition switch position) prohibiting the movement of the window. If the window being operated is the driver door window, and if no prohibitive class 2 messages have been received, the DDM then applies voltage and ground to the driver door window motor to move the window glass as requested. If the window being operated is a passenger door window, and no prohibitive class 2 messages have been received, the DDM sends the request, via the power door serial data circuit, to the appropriate passenger door module. The passenger door module then applies voltage and ground to the passenger door window motor to move the window glass as requested.
When a passenger door window is operated from the power window switch mounted locally to its associated door, the passenger door module first checks to see if the DDM has received any prohibitive class 2 serial data messages. If there are no prohibitive messages, the passenger door module powers the associated passenger door window motor.
Both front door windows have the express down feature. This allows the front door windows to be fully opened by momentarily pulling the appropriate window switch lever to the second detente and then releasing.
Oct 30, 2016 | Buick Cars & Trucks
Jan 05, 2016 | 2001 Ford Explorer
Sep 16, 2015 | 2012 Ford Escape
Mar 22, 2015 | 1999 GMC Suburban
Mar 24, 2014 | 2003 Toyota Avalon
Jul 08, 2017 | 2000 Kia Sephia
Jan 19, 2011 | Volkswagen Rabbit Cars & Trucks
Sep 19, 2009 | 1997 Ford Explorer AWD
Aug 06, 2009 | 1996 Lincoln Town Car
Mar 22, 2009 | 1998 GMC Safari
228 people viewed this question
Usually answered in minutes!