Question about 1995 Dodge Dakota

1 Answer

Where is the crank sensor located on a 1995 dodge dakota 4 cylinder

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 127 Answers

Most are screwed into into front cover just behind front pully, look for some wires coming from that area. It is possible it could be in very rear of engine where it can catch a signal from flywheel

Posted on Mar 23, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crank shaft sensor on a 1995 Dodge Dakota Sport manual, 4 cylinder, 2.5?


Behind the harmonic balancer mounted on the front of the crank shaft.

May 12, 2015 | Dodge Cars & Trucks

1 Answer

Crank angelsensor on a 1993 Dodge Dakota 2.5 4 cyl location


It should have a distributor which would cancel the need for a crank sensor.

Mar 06, 2015 | 1993 Dodge Dakota

1 Answer

I have a 94 dodge Dakota, with a 318 motor. it turns over but doesn't fire. undefined


crank sensor usually the problem located on the rear side of the passenger cylinder head it reads off the flywheel cam sensor is your distributor

Sep 22, 2014 | 1994 Dodge Dakota Club Cab

1 Answer

Im looking for a diagram of where the crankshaft sensor is on a 1995 dodge dakota v8 4x4


Your sensor is located on the front of your engine, it's mounted at the
HARMONIC BALANCER which is on the very frount of the crank shaft.

Nov 02, 2012 | 1995 Dodge Dakota

1 Answer

Were is the crankshaft position sensor located on a 2003 dodge dakota with a 4.7l engin


ANSWER: CRANKSHAFT POSITION SENSOR - 4.7L V-8 ENGINE
REMOVAL
The Crankshaft Position (CKP) sensor is located at the right-rear side of the engine cylinder block CKP Sensor Location/Removal/Installation - 4.7L V - 8 Engine the cranks sensor is positioned and bolted into a machined hole in the engine block

Disconnect CKP electrical connector at sensor.
Remove CKP mounting bolt CKP Sensor Location/Removal/Installation - 4.7L V - 8 Engine
Carefully pry sensor from cylinder block in a rocking action with two small screwdrivers.
Remove sensor from vehicle.
Check condition of sensor o-ring.
INSTALLATION
Clean out machined hole in engine block.
Apply a small amount of engine oil to sensor o-ring.
Install sensor into engine block with a slight rocking action. Do not twist sensor into position as damage to o-ring may result
CAUTION: Before tightening sensor mounting bolt, be sure sensor is completely flush to cylinder block. If sensor is not flush, damage to sensor mounting tang may result.

Install mounting bolt and tighten to 28 N·m (21 ft. lbs.) torque.
Connect electrical connector to sensor.

Jun 29, 2010 | 2003 Dodge Dakota Club Cab

1 Answer

Where is the feul fifter for 1995 dodge dakata?


the 4 cylinder 2.5L fuel filter located under the bed of the vehicle along the left side frame rail. the V6 and V8 fuel fuel filter located in the fuel pump module,on the top of the fuel tank.

May 13, 2010 | 1995 Dodge Dakota

2 Answers

'95 Dodge Dakota, 318 cu. in. no spark


There is a sensor that located on the right side of trans. that goes into bellhousing up close to the engine, it runs off the flywheel i think its the crank sensor but i'am not sure, i had a simmler problem with one i was working on, replaced that and it ran.

Apr 09, 2009 | 1995 Dodge Dakota

2 Answers

Cant find crank position sensor on 1991 dodge dakota with a 3.9 liter engine 2wd auto.


Can not find crank sensor on 1995 Dodge Dakota how hard is it to replace

Jul 24, 2008 | 1995 Dodge Dakota

Not finding what you are looking for?
1995 Dodge Dakota Logo

117 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...