Question about Hyundai Motor 2003 Sonata

Open Question

I need timing mark alignment marks on 3.5 liter

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

maklean
  • 1665 Answers

SOURCE: 2002 Sonata 2.0 timing

There is an answer at this link
http://en.allexperts.com/q/Hyundai-Repair-815/Timing-belt-replacment-1.htm

Posted on Jun 24, 2008

  • 65 Answers

SOURCE: I changed the timing belt

If you are hearing the valves hitting the pistons then you have already done head damage but below id the marks:
3ade973.jpg

Posted on Oct 04, 2008

daves944
  • 1050 Answers

SOURCE: how do i align timing marks on a 93 hyundai sonata

Hopefully this picture comes through, if not let me know and I can zoom in. Be sure to remove the auto tensioner, compress it slowly in a vice and put a pin through holding holes until the belt is mounted properly, replace it and pull the pin.432732a.jpg

Posted on Mar 26, 2009

  • 12 Answers

SOURCE: Correct way to align timing marks

hi -- the timing marks on a twin cam are tricky!! heres how- turn the motor over to tdc on the bottom pulley,this will align two marks on the lower cog-----now on the top cog,it has an obvious mark near the teeth-- well disregard this for now!! the cog has a hole in it,in one of the spokes,well this goes at 12 o,clock and lines up with a mark you will see on the housing! now if you are right you will see the mark near the teeth is at around 4,oclock---i just did one and it is right--cheers

Posted on May 28, 2009

  • 196 Answers

SOURCE: 1998 Elantra: i need timing marks for 98 elantra 2.0 1.8 l...

the camshaft is the dot on the sprocket there is a small mark behind it on the cover 12 oclock the crank there is a mark on it look to the ten oclock number 1 tdc you will see the mark

Posted on May 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Aligning timing belt after breakage on 1996 toyota camry 2.2 liter 4 cylinder


Dustin, The attached links will explain timing alignment on 2.2 Camry engine. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Diagram of Timing Belt Marks and Installation
work on camry engine
Aligning timing belt after breakage on 1996 toyota camry 2 2 liter 4...
DIY GEN3 Timing Belt Waterpump Oil Seal Change Part 1 Toyota Nation Forum...

May 15, 2016 | Toyota Cars & Trucks

1 Answer

Camry timing belt


I am assuming you are referring to a 2.2 liter 5SFE engine. If so camshaft timing mark is dot located on forward face of sprocket mid spoke/or a notch on inboard rim of sprocket. locate mark and paint with white paint. Locate timing mark-small raised dot on plate behind sprocket at approx. one o-clock position paint this white for easy reference. Crank shaft sprocket has small notch on inboard rim. paint white for reference. align cam timing marks, then align crankshaft mark with #0 on timing scale. Adjust tensioner and belt is aligned. I recommend changing idler pulleys and water pump when replacing belt as preventative maintenance. Also inspect shaft oil seals and replace as needed. Performing these services now will save time and money in the future.

May 09, 2014 | 2001 Toyota Camry

1 Answer

Do you have a diagram for 2003 saturn timing belt


The 2.2 liter engine uses colored links on the timing chain to align with the marks on the gears. You just have to rotate the engine to where the copper chain link is up on the upper right side of the intake can gear--aligned to the INT diamond on the gear. Then the silver link should be down at about 5 O-Clock on the crankshaft timing mark. The other silver link should then be aligned to the mark on the exhaust cam sprocket. See picture below.

For the 3.0 liter engine, there are marks on the belt that line up with marks on the gears. The book calls out special tools to hold the cam sprockets in alignment while the belt is put on. There is also a special tool to lock the belt onto the crankshaft sprocket. See pictures below.
Please let me know if you have questions.

2.2 liter:

jturcotte_425.gif



jturcotte_426.gif

3.0 liter:
camshaft sprocket alignment with belt marks

jturcotte_427.gif


Camshaft locking tools

jturcotte_428.gif



Crankshaft belt tool

jturcotte_429.gif


Properly adjusted tensioner

jturcotte_430.gif

Dec 08, 2010 | 2003 Saturn VUE

1 Answer

Replacing 2000 dodge caravan timing belt - how do


rotate crankshaft in a clockwise direction until both timing marks are aligned together on both camshaft gears and the crankshaft timing mark aligns with mark on the block just behind the crankshaft gear. you may need to rotate the crankshaft gear several times before you can get all the timing marks to align. once you have done this then insert a allen wrench in the hole on the belt tensioner and a small drill bit or a small allen wrench in the smaller hole. take the largr allen wrench and apply pressure counterclockwise until the small drill bit or allen wrench slides into locking hole to hold the belt tensioner in place. install belt and release the tensioner. (note: before starting work on engine remove the negative cable from battery).

Apr 14, 2010 | 2000 Dodge Caravan

1 Answer

Timing belt marks 2001 lanos 1.6 liter


The camshaft sprockets have an indention on them you will align them to the inside horizontally so they are side by side. The crankshaft sproket also has a timing mark on it and you will align that with the timing mark on the rear timing belt cover vertically. The tensioner aligns with with the notch on the automatic tensioner bracket. Hope this helps you.

Nov 29, 2009 | 2001 Daewoo Lanos

1 Answer

Camshaft timing mark crankshaft timing mark


Belt covers need to be on. Timing mark on crankshaft (while on compression stroke) should line up with TDC mark on cover. then Camshaft mark, needs to line up by looking through access hole of cover, and align mark on cam sprocket with pointer on inside of belt cover.

Oct 22, 2009 | 1987 Ford Ranger

1 Answer

Timing belt. 1990 2.3 liter 4 cyl. Crankshaft


there should be a mark on the crankshaft pulley there should be a mark on the camshaft pulley and they should line up but to be sure bring the motor to tdc then line your mark up on your camshaft

May 02, 2009 | 1993 Ford Ranger SuperCab

1 Answer

Timing for tropper 6cly and 4 camshafts and 24 valves model 2000


Timing Belt
Removal
1. Disconnect battery ground cable.
2. Remove air cleaner assembly.
3. Remove radiator upper fan shroud from radiator.
4. Move drive belt tensioner to loose side using wrench
then remove drive belt.
850RW001
Legend
(1) Crankshaft Pulley
(2) Cooling Fan Pulley
(3) Tensioner
(4) Generator
(5) Air Conditioner Compressor
(6) Power Steering Oil Pump
(7) Drive Belt
5. Remove cooling fan assembly four nuts, then the
cooling fan assembly.
6. Remove cooling fan drive pulley assembly.
7. Remove idle pulley assembly.
8. Remove serpentine belt tensioner assembly.
9. Remove power steering pump assembly.
10.Remove crankshaft pulley assembly using
5–8840–0133–0 crankshaft holder, hold crankshaft
pulley remove center bolt, then the pulley.
11. Remove right side timing belt cover then left side
timing belt cover.
12. Remove lower timing belt cover
13. Remove pusher.
CAUTION: The pusher prevents air from entering
the oil chamber. Its rod must always be facing
upward.
014RW011
Legend
(1) Up Side
(2) Down Side
(3) Direction For Installation
(4) Locking Pin
14. Remove timing belt.
CAUTION:
1. Do not bend or twist the belt, otherwise its core
could be damaged. The belt should not be bent at
a radius less than 30 mm.
2. Do not allow oil or other chemical substances to
come in contact with the belt. They will shorten
the life.
3. Do not attempt to pry or stretch the belt with a
screw driver or any other tool during installation.
4. Store timing belt in a cool and dark place. Never
expose the belt direct sunlight or heat.
6A–30 ENGINE MECHANICAL
Installation
NOTE: For correct belt installation, the letter on the belt
must be able to be read as viewed from the front of the
vehicle.
014RY00042
Legend
(1) Crankshaft Timing Pulley
(2) RH Bank Camshaft Drive Gear Pulley
(3) Water Pump Pulley
(4) Idle Pulley
(5) LH Bank Camshaft Drive Gear Pulley
(6) Tension Pulley
014RY00043
Legend
(7) Alignment Mark on Oil Pump.
(8) Alignment Mark on Timing Belt
(9) Alignment Mark (notch) on Crankshaft Timing
Pulley.
(10) Alignment Mark (groove) on Crankshaft Timing
Pulley.
014RW006
Legend
(1) Timing Belt
(2) Engine Rotation Direction
(3) Cylinder Head Side
1. Install timing belt.
1. Align the mark (notch) of crankshaft timing pulley
(2) with mark on oil pump (1).
Align the mark (groove) on the crankshaft timing
pulley (3) with alignment mark (white dots line) on
the timing belt (4).
NOTE: When timing marks are aligned, No.2 piston will
be on Top Dead Center.
014RW003
Legend
(1) Alignment Mark on Oil Pump
(2) Groove on Crankshaft Timing Pulley
(3) Alignment Mark on Crankshaft Timing Pulley
(4) Alignment Mark on Timing Belt
ENGINE MECHANICAL 6A–31
2. Align the alignment mark on the RH bank
camshaft drive gear pulley (2) to the alignment
mark of the cylinder head cover RH (3).
3. Align the alignment mark (white line) on the timing
belt (1) with alignment mark on the RH bank
camshaft drive gear pulley (2) (on the left side as
viewed from the front of the vehicle) and put the
timing belt on the camshaft drive gear pulley.
Secure the belt with a double clip or equivalent
clip.
014RW00004
Legend
(1) Alignment Mark on Timing Belt (White line).
(2) Alignment Mark on Camshaft Drive Gear
Pulley.
(3) Alignemnt Mark on Cylinder Head Cover RH.
4. Align the alignment mark on the LH bank
camshaft drive gear pulley (2) to the alignment
mark of the cylinder head cover LH (3).
5. Align the alignment mark (white line) on the timing
belt (1) with the alignment mark on the LH bank
camshaft drive gear pulley (2).
When aligning the timing marks, use a wrench to
turn the camshaft drive gear pulley, then set the
timing mark between timing belt and camshaft
drive gear pulley and put the timing belt on the
camshaft drive gear pulley.
Secure the belt with a double clip or equivalent
clip.
NOTE: It is recommended for easy installation that the
belt be secured with a double clip or equivalent clip after
it is installed the timing belt to each pulley.
014RW00005
Legend
(1) Alignment Mark on Timing Belt (White line).
(2) Alignment Mark on Camshaft Drive Gear
Pulley.
(3) Alignemnt Mark on Cylinder Head Cover LH.
6. Install crankshaft pulley temporarily and tighten
center bolt by hand (do not use a wrench).
Turn the crankshaft pulley clockwise to give some
belt slack between the crankshaft timing pulley
and the RH bank camshaft drive gear pulley.
2. Install pusher and tighten bolt to the specified torque.
Torque : 25 N·m (2.5 Kg·m/18 lb ft)
1. Install the pusher while pushing the tension pulley
to the belt.
2. Pull out pin from the pusher.
NOTE: When reusing the pusher, press the pusher with
approximately 100Kg to retract the rod, and insert a pin
(1.4 mm piano wire).
014RW011

Mar 18, 2009 | 2000 Isuzu Trooper

1 Answer

I need a timing belt diagram for a 1994 ford ranger 2.3 liter.


Bottom pulley at 0 (TDC), dystributor rotor indicating cylinder one and marks on head an top cam pulley that will align exactly with valves on cylinder number 1 on compression, both closed (perhaps one mark exactly at 12 o clock) (or two marks one at 9 o clock an the other at 3 o clock ) but on front of cm pulley

Jan 23, 2009 | Ford Ranger Cars & Trucks

Not finding what you are looking for?
Hyundai Motor 2003 Sonata Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...