Question about 2000 Ford F250 Super Duty Crew Cabs

2 Answers

Does the caliper mounting braket bolts slide into the caliper to enable the caliper to slide over the extra thickness of the new brake pads? I have already got the caliper all the way in but it still won't fit over the width of the rotor and pads. My only guess is that the bolt mounts slide in as there is a rubber protector over the mount. How do I get this in? c-clamp

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 249 Answers

Remove the caliper from the caliper bracket and install caliper bracket on spindle ... install brake pads then clean and lube slider bolts and mounting holes in bracket and install caliper.. Sometimes dirt and rust prevent bolts from bottoming in caliper bracket.
Hope this helps.

Posted on Mar 23, 2011

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 136 Answers

Do you have the actual caliper piston fully pushed into the rear of the caliper? Not the bolts, the piston. It's in the center of the caliper and about as big around as the bottom of a tin can.

Posted on Mar 23, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brakes don't open up brakes lock pads stay against


you will need to find out if this is due to stuck pads on the bracket or a brake hose or bad caliper, the first step is to open the bleeder screw on the caliper and see if the brakes release if they due then its a hose if they dont then move to checking caliper, remove the caliper and see if the pads slide on and off the bracket with ease if not then clean braket so pads slide on by hand and also use a c clamp and push piston back in, this should be easy if its real hard to turn the c clamp then caliper is bad, and last is the caliper slides, this is the slides that the caliper moves on, the bolts bolt to it, make sure they slide in and out with ease.

Jun 25, 2011 | Mitsubishi Passenger Cars & Trucks

1 Answer

How to replace front discs and pads


Front brakes are very simple to do:
  • Pull off the front tires.
  • Remove the brake pads by removing the slide pin bolts where the piston assembly attaches to the caliper mounting bracket. The slide pin bolts are usually a 12 or 14mm bolt. Once the piston assembly is free slide the old brake pads out.
  • Compress the piston back into the caliper by using a large pair of channel lock pliers or a c-clamp. If you don't do this, you won't be able to get the new pads on.
  • Before you put the new pads on, replace the rotor.
  • Remove the two bolts for the caliper mounting bracket. They are in the back and are bigger than the slide pin bolts. Usually a 17 or 19mm bolt.
  • Pull off the caliper mounting bracket.
  • At this point the old rotor should slide right off. If it doesn't slide right off, look for a screw in the center of the rotor, some cars will have a screw there to hold the rotor on. If there's no screw and it still won't come off, try tapping it with a hammer. If you're replacing the rotor, don't be shy.
  • Put the new rotor on. Make sure to clean off any grease with brake cleaner that may be on the braking surface from packaging.
  • Put the caliper mounting bracket back on.
  • Put the new brake pads on. Make sure to use some anti-squeal grease on the back of the pads.
  • Put the caliper assembly back on with the slide pins. Grease up the slide pins as well.
  • Put the wheels back on.
  • Make sure to pump your brakes 10 - 15 times before you drive off. Because you compressed the piston back into the caliper, the piston will not be contacting the brake pads unless you pump the brakes.

Good Luck!
~Brandon

May 27, 2011 | 2002 Mitsubishi Lancer

2 Answers

How to change brake pad and check rotors


Brake Pads Removal & Installation Front for_car_toy_cam_02-04_sst_frt_dsc_asm.gif

To Remove:
  1. Drain brake fluid to ½ full level in reservoir.
  2. Remove the front wheels. toy_car_cam_frontbrakepads.gif

  3. Remove the front brake caliper assembly.
  4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
  5. Remove the wear indicator from each of the 2 brake pads.
To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.
toy_car_cam_frontbrakepads.gif

  1. Using a large C clamp or equivalent press piston into the caliper.
  2. Apply disc brake grease to the inside of each anti-squeal shim.
  3. Install the anti-squeal shims on each pad.
  4. Install the pad wear indicator clip to the pads.
  5. Install the pads with the pad wear indicator plate facing upward.
  6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
  7. Install the front wheels.
  8. Fill the master cylinder with new clean brake fluid.
  9. Pump the brake pedal several times to seat the brake pads.
Rear TMC made rear brake components toy_car_cam_tmcrearbrakes.gif

TMMK made rear brake components toy_car_cam_tmmkrearbrakes.gif

To Remove:
  1. Drain the brake fluid to ½ full level in reservoir.
  2. Remove the rear wheels.
  3. Remove the caliper slide pins.
  4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
  5. Remove the rear brake calipers.
  6. Remove the 2 brake pads with the anti-squeal shims.
  7. Remove the anti-squeal shims and pad wear indicators from brake pads.
To Install:
  1. Using a large C clamp or equivalent press the piston into the caliper.
  2. Coat both sides of the outer anti-squeal shim with pad grease.
  3. Install anti-squeal shims to each pad.
  4. Install wear indicators on the 2 brake pads.
  5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
  6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
  7. Fill the master cylinder with new clean brake fluid.
  8. Pump the brake pedal several times to seat the brake pads.
  9. Install the rear wheels.
prev.gif next.gif Brake Rotor Removal & Installation Front To Remove:
  1. Remove the front wheels.
  2. Remove the front brake caliper assembly.
  3. Remove the front brake pads.
  4. Remove the 2 bolts and caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the front wheel disc.
To Install:
  1. Align the match marks and install the front disc.
  2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
  3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the front wheel.
Rear To Remove:
  1. Remove the rear wheels.
  2. Remove the brake caliper assembly.
  3. Remove the brake pads.
  4. Remove the 2 bolts and the caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the rear disc.
To Install:
  1. Align the match marks and install the rear disc.
  2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
    • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
    • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
  3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the rear wheel
prev.gif next.gif

Jan 25, 2011 | 2007 Toyota Camry

1 Answer

How can I change the rotors and brakes on a 2006 Cadillac?


Front brake
Step 1: Identify Front Disc Brake Components
brake_pads_rotor.jpg
Front Wheel Drive Brake Assembly
Most front disc brake components include: brake rotor, brake pads, brake caliper, caliper mount and brake flex hose. Brake service usual occurs between 20,000 and 40,000 miles depending on driver habits, road conditions and brake pad/ rotor materials used.
Step 2: Remove Brake Caliper to Replace Pads
brake_pad_set.jpg
Removing Brake Caliper Mounting Bolts
Locate primary caliper mounting bolts; apply wrench pressure counter-clockwise (When looking at the head of the bolt) to remove the bolts, upper and lower. Make sure the bolt threads are in good shape and replace if necessary.
Step 3: Remove Front Brake Caliper
remove_brake_caliper.jpg
Remove Front Brake Caliper
After removing the primary caliper mounting bolts lift the brake caliper off of the rotor and then tie or secure to the side, being careful not to bend or kink the brake caliper flex hose. Thoroughly inspect brake caliper and brake hoses for leakage, cracks or chaffing and replace as needed. Next remove the brake pads (If not mounted in the caliper) and secondary caliper mounting bolts. Notice how great protective gloves work, most technicians use them on the job today.
Step 4: Remove Brake Pads
remove_brake_pads.jpg
Remove Front Brake Pads
Once the brake pads have been removed, make sure if there is anti rattle hardware to transfer to the new brake pads. Some brake pad manufacturers will include the proper lube (Caliper slides) and anti-rattle hardware to ensure proper performance of their product.
Step 5: Remove Caliper Mount
remove_brake_pads_holder.jpg
Remove Caliper Mount Bracket
Finish removing secondary caliper mount bolts and remove caliper mount. Note: clean and lube caliper slides and pad friction surfaces of all foreign material or build-up.
Step 6: Remove Brake Rotor
brake_rotor.jpg
Remove Brake Rotor
With the caliper mount out of the way you can now remove the brake rotor. Sometimes it can get stuck so you may need to tap it with a hammer or use penetrating oil to free it up. Some manufacturers use small screws to hold the rotor on as well. Clean and inspect wheel studs, replace if any are damaged. Also clean bearing hub rotor mount surface to ensure the proper mounting of the new brake rotor. Inspect the ABS sensor wheel for cracks or damage and replace as needed.
Step 7: Depressing the Brake Caliper
compress_caliper.jpg
Resetting Brake Caliper
To install the new brake pads you must retract the brake caliper piston. Remove the master cylinder lid or open the brake caliper bleeder screw to allow excess brake fluid to be released if necessary. Install C clamp tool and gently tighten clamp until caliper piston is fully depressed. Note: use old brake pad to protect the caliper piston. Close the bleeders once the piston is retracted completely
Step 8: Installing New Brake Rotor
new_brake_rotor.jpg
Install Brake Rotor
Install new brake rotor, the new rotor is manufactured with a protective film over the rotor to keep it from rusting, remove protective film with brake cleaner before installing; also after the brake job is complete you may experience a small amount of smoke from the rotor when first used. This is normal and will go away after the first couple of uses.
Step 9: Installing New Front Brake Pads
new_brake_pads.jpg
Installing New Brake Pads
Reinstall the front brake caliper mount, and then install front brake pads. Make sure the pads are seated properly in the caliper mount; it must be a close fit to work properly..
Step 10: Reinstall Front Brake Caliper
front_brake_rotor_pads.jpg
Re-Install front Bake Caliper
Reinstall front brake caliper and reinstall caliper-mounting bolts, recheck all mounts and mounting bolts. Check the caliper slides to be sure there is no bind and that the caliper moves freely back and forth on the caliper slides. Bleed brake system per manufacturer's specifications to relieve any air trapped in the system. Before driving the vehicle, push the brake pedal down and let it up slowly, repeat until normal brake pedal operation resumes, this operation is forcing the brake pads to travel to the brake rotors.

Dec 18, 2010 | 2006 Cadillac STS

1 Answer

Will I need a caliper reset tool kit to change the brakes on my 2007 toyota sienna or will a standard c-clamp do the job? And since it is an ABS system, I assume that brakes must be bled, correct?


Brake Pads Removal & Installation Front To Remove:
  1. Remove the front wheels. Front brake caliper (exploded view) toyota-09-00-5838.gif

  2. Loosen the caliper bleeder.
  3. Hold the slide pin; remove the 2 mounting bolts and remove the brake caliper from the support.
  4. Support the caliper.
  5. Open the brake bleeder. Press the caliper piston into the bore.
  6. Close the bleeder after the piston has reached the bottom of the caliper bore.
  7. Remove the brake pads, support plates, wear indicators and anti squeal shims.
  8. Remove the slide pins and bushings from the caliper support.
To Install:
  1. Lubricate the slide pins and bushings with brake grease.
  2. Install the bushing on the slide pin.
  3. Install the slide pin on the caliper support.
  4. Install the brake pad support plates on the caliper supports.
  5. Lubricate the anti squeal shims with brake grease.
  6. Install the anti squeal shims on the brake pads.
  7. Install the pad wear indicator facing upward and install the pads on the caliper support.
  8. Install the caliper on the support.
  9. Install the 2 mounting bolts, hold the slide pins and tighten 25 ft-lb (34 Nm).
  10. Fill the reservoir and bleed the brakes.
  11. Install the front wheels.
Rear To Remove:
  1. Remove the rear wheels.
  2. Loosen the caliper bleeder. Rear brake caliper (exploded view) toyota-09-00-5842.gif

  3. Hold the slide pin; remove the 2 mounting bolts and rear brake caliper assembly from the support.
  4. Support the caliper.
  5. Open the brake bleeder. Press the caliper piston into the bore.
  6. Close the bleeder after the piston has reached the bottom of the caliper bore.
  7. Remove the brake pads, support plates, and anti squeal shims.
  8. Remove the slide pins from the caliper support.
To Install:
  1. Lubricate the slide pins with brake grease.
  2. Install the slide pin on the caliper support.
  3. Install the brake pad support plates on the caliper supports.
  4. Lubricate the anti squeal shims with brake grease.
  5. Install the anti squeal shims on the brake pads.
  6. Install the rear pads on the caliper support.
  7. Install the rear caliper on the support.
  8. Install the 2 mounting bolts, hold the slide pins and tighten 25 ft-lb (34 Nm).
  9. Fill the reservoir and bleed the brakes.
  10. Install the front wheels.
prev.gif next.gif

Sep 18, 2010 | 2007 Toyota Sienna

1 Answer

How to change front brake pads on 2003 Chevy Suburban


Disc Brake Pads for Suburban 1500 Removal & Installation Front To Remove:
Front caliper mounting bracket 93086g95.gif

  1. Remove the cover on the master cylinder and siphon out 2/3 of the fluid. This step prevents spilling fluid when the piston is pushed back into the caliper bore.
  2. Raise and support the vehicle safely.
  3. Remove the wheel and tire assembly.
  4. Compress the brake piston back into its bore using a C-clamp.
  5. Remove the 2 caliper mounting bolts. Lift the caliper off the rotor.
  6. Remove the inboard and outboard pad.
  7. Remove and discard the anti-rattle clips.
To Install:
Caliper bracket sleeves 93086g97.gif

  1. Thoroughly inspect, clean and lubricate all caliper slide points, bolts and hardware.
  2. Install new anti-rattle clips.
  3. Position the inboard and outboard pads into the support bracket
  4. With the 2 pads in position, place the caliper over the brake rotor and align the holes in the caliper with those of the mounting bracket.
  5. Install the caliper mounting bolts through the sleeves in the inboard caliper ears and into the mounting bracket.
  6. Tighten the mounting bolts to: 80 lb. ft, (110 Nm).
  7. Install the tire and wheel assembly. Lower the vehicle.
  8. Add fluid to the master cylinder reservoirs so they are 1/4 in. (6.35mm) from the top.
  9. Test the brake pedal by pumping it to obtain a hard pedal. Check the fluid level and add fluid as necessary.
Rear To Remove:
  1. Remove 2/3 of the brake fluid from the master cylinder.
  2. Raise and safely support the vehicle.
  3. Remove the wheel and tire assembly.
  4. Remove the brake caliper mounting bolts. Suspend the caliper from the frame with mechanic's wire. Do not allow the caliper to hang from the brake hose.
  5. Remove the brake pads from the caliper mounting bracket.
  6. Remove and discard the anti-rattle clips.
Rear brake caliper 93086g96.gif

To Install:
  1. Install new anti-rattle clips.
  2. Position the brake pads to the caliper mounting bracket.
  3. With the 2 pads in position, place the caliper over the brake rotor and align the holes in the caliper with those of the mounting bracket.
  4. Install NEW caliper mounting bolts. Tighten to: 30 lb. ft, (40 Nm).
  5. Install the wheel and tire assembly.
  6. Lower the vehicle.
  7. Refill the master cylinder to the proper level with fresh brake fluid. Pump the brake pedal slowly and firmly to seat the brake pads. Burnish the brakes as needed.
prev.gif next.gif

Jul 05, 2010 | 2004 Chevrolet Suburban

2 Answers

How do you change the front disk pads


The pads are mounted to the caliper. The caliper is bolted to the spindle bracket. There is brake hardware which should be replaced with the pads.
Look behind the wheel at the backside of the spindle bracket. The spindle bracket is on the verticle shaft with coils on one end and an A shaped bracket on the other. There are usually 2 bolts that may have normal bolt ends or "Allen" bit fittings.

When you buy the brake hardware you can check for the proper socket for the mounting bolt. You unbolt the caliper, use a rope or wire to suspend it under the frame without disconnecting the brake line.

The pads come off with the hardware. You need to compress the caliper pistons to make the new pads fit. Use a C clamp and an old pad to squeeze the pistons back into the caliper. Remove the Master Cylinder cover so fluid can return.

Then use a bonding chemical like "brake quiet" to mount the rear pad to the caliper piston. Mount outside pad to caliper and then slide caliper over the rotor on the spindle bracket. Lube the slides of the new brake hardware and bolt into place.

You should have the rotors checked for thickness and whether they are warpped before you put on the new pads.

May 17, 2010 | Cars & Trucks

1 Answer

HOW TO INSTALL FRONT BRAKE PADS AND ROTORS ON A 1997 MITSUBIAHI ECLIPSE


take the front wheels off,remove the 2 bolts holding the caliper to the caliper mounting bracket and then remove the caliper and then take the old pads out while you remember which ones went where and the put the new ones on the mounting bracket and then get a pliers to push the caliper piston in so they fit over the new thick pads and then slide the caliper over the new pads and then put the 2 bolts back in and then the wheel, then the other side

Oct 15, 2009 | 1997 Mitsubishi Eclipse

2 Answers

How do i remove front pads from 89 probe?


the caliper has 2 bolts holding it in.remove the bolts.slide off the caliper and replace the pads.you need to put a lubricant on the pads,and compress the pistons in all the way with a caliper piston tool,costs about 10 dollars.,or the new pads which are much thicker will not go on.also lube the bolts,known as slider pins or they can jam up.if there is brake pulsation you need to turn the rotors.to remove the rotors ,you need to remove the bracket that the caliper bolts to.there are 2 bolts holding on the bracket.then the rotor can come off to be turned.if the rotors are not thick enough after turning,,they need to be replaced

Jul 13, 2009 | 1994 Ford Probe

1 Answer

Help with changing fron brakes on a 2006 dodge ram truck


After you have removed the caliper from the caliper mounting bracket, remove the pads and guides.  Make sure you have fully depressed the caliper's piston fully then you can start by putting the little guides back in then reloading the new pads back in the caliper.  Be sure to use some caliper grease on the caliper mounting bolts (the bolts that hold the caliper in place).  If you don't use grease on these mounting bolts, your caliper won't slide right and you can have uneven wear on your pads.  This could easily cause overheating.  Once you place the caliper back in the mounting bracket and tighten the caliper mounting bolts back down tight you are all done.  Put your wheel back on and tighten the lug nuts and you're done!
MAKE SURE WHEN YOU FIRST START THE TRUCK FOR A TEST DRIVE AFTER INSTALLING THE BRAKES, YOU NEED TO PUMP THE BRAKES BACK UP!!!!  IF YOU DON'T YOU WILL START DRIVING AND HAVE NO BRAKES!!!  PUMP YOUR BRAKES ABOUT 10-15 TIMES FULLY OR UNTIL THE BRAKE PETAL SEEMS FIRM.  ALLOW THE BRAKE PETAL TO COME ALL THE WAY BACK UP BEFORE PUMPING THEM AGAIN.

Feb 02, 2009 | 2006 Dodge Ram 3500 Truck

Not finding what you are looking for?
2000 Ford F250 Super Duty Crew Cabs Logo

185 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...