Question about 1996 Oldsmobile Silhouette

Open Question

How do i change the throttle cable on a 98 olds silhoutte

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change a front turn signal bulb in my 2002 Olds Silhoutte van?


You should see a large plastic wingnut holding the entire headlight assembly to the fender. Remove that and pull the headlight assembly straight out. Then you can access the turn signal bulb

Dec 02, 2017 | Cars & Trucks

2 Answers

Intake manifold torque specs 2000 olds silhoutte 3.4


Follow the link for a complete listing of this engines bolt torque specs. Torque Specs Database

Jan 25, 2017 | 2000 Oldsmobile Silhouette

1 Answer

How do I reset bcm in 1995 olds silhoutte


Try pulling battery positive side cable off for about 20 minutes than re attaching. If this was helpful please leave good feed back

Feb 18, 2015 | 1995 Oldsmobile Silhouette

1 Answer

2001 OLD SILHOUTTE SHIFTING ISSUE


Filter or valve problem in the transmission. Transmissions also need regular fluid changes and filter changes and most people do not know this. You can do this yourself, or have someone do it.

Sep 10, 2012 | 1996 Oldsmobile Achieva

1 Answer

My 2002 Oldsmobile Silhoutte's coolant gage running hot


Change the thermostat,and bleed the air out of the system,and make sure the cooling fans are coming on,and then going off,on there own,with the ac off,if this was helpful,please rate,thank you.

Jul 05, 2010 | 2000 Oldsmobile Silhouette

2 Answers

Gas throttle hangs up on my 98 ford expidition any clues why


check the throttle cable where it connects to the throttle body,they have a history of rusting there and holding throttle up.

Jan 05, 2010 | 1998 Ford Expedition

1 Answer

How to change out a power steering pump on 2001 olds silhoutte


How to change out a power steering pump on windstar 2000

Mar 16, 2009 | 2001 Oldsmobile Silhouette

3 Answers

98 lexus gs300 codes p1120 p1121


I wanted to start a thread specifically about failures within the throttle body concerning the GS300 (1998 in my case)

My symptons were:
VSC, VSC OFF, and ENGINE Lights would come on, followed by my car going into Limp Mode, where only that last 25% (if that) of the throttle would respond (basically have to floor the pedal to even move at all).

During the mornings, or when the engine was COLD, the throttle operated normal...then once the car warmed up, usually at about 10 mins, the problem would start...it happened intermitantly at first...1 or 2 days over the course of a week, then it became more consitent, until last week it became a daily problem.

The first part I tried was the Throttle Position sensor, which is on the front side of the throttle body, and the easiest thing to replace...this didnt help at all. $300 part from Lexus, $80 part from RockAuto.com (exacly same part toyota OEM)

THE PART THAT FIXED THE PROBLEM:
===========================================
"Idle Valve Motor", which is the larger electrical object next to the TPS on my 98 GS300. Problem is solved.

The Codes I got were P1120 and P1121 - Accelerator Sensor problem. However it wasnt really the Accelerator Sensor, it was indeed to actual electrical Motor that controls the opening of the Butterfly valve inside the Throttle body.

I found the problem by good old trouble shooting, and using an ohm meter to see if the throttle electric motor was getting elev, I found that the elec motor just to the left of the TPS was basically freaking out and shutting down. The Accelerator Pedal Sensor is on the Back-side of the throttle body where the throttle cable connects to, and has a spring on it. It was fine.

GS300's are indeed "drive by wire" concerning the throttle...the cable triggers the Accel Pedal Sensor, which sends a signal to the ECU, the ECU then sends power to the Idel Valve Elec Motor (next to the TPS), which opens and closes the mechanical butterfly valve, then the TPS sensor detects how far the elec motor is actually opening the butterfly valve...its a closed-loop feed-back system, meaning any failure in any sensor will cause the entire systm to fail.

The throttle cable apparently is ONLY there to allow the fail-safe of having that last 10-25% throttle when the electronic system fails...there is a gearbox inside the throtle body which allows the tail end of the throttle to manually engage the butterfly valve...the rest of the time, the butterfly valve is 100% opened and closed via the idle control motor.

Nov 23, 2008 | 1998 Lexus Gs 300

Not finding what you are looking for?
1996 Oldsmobile Silhouette Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8826 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...