Question about 1998 Chevrolet Cavalier

1 Answer

Replacing the head on chevy cavalier 2.2 need to know what to torque head bolts

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 54 Answers

On the first pass, torque the long bolts to 46 foot pounds, short bolts to 43 foot pounds. On the final pass, turn all bolts and additional 1/4 turn.

Posted on Mar 23, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 cavalier head torque spectson head bolts, and cams bolts


Visit the on-line store, know as reliable-store, they have the repair manuals. I'm sure you will get the solution of your problem.
Chevy Cavalier 1995 2005 Factory Service Workshop repair manual

Jul 30, 2016 | Cars & Trucks

1 Answer

I have a 1997 Chevy Cavalier and i'm tryin to torque the head down. I need to know the pattern sequence


The sequence is pretty much the same for ANY cylinder head. Start with the bolts in the center and work your way left, then right, then left, etc. toward the ends.

Feb 01, 2011 | 1997 Chevrolet Cavalier

2 Answers

1997 cavalier head gasket replacement with a 2.2. Also need the torque specs and sequence for the head bolts


Go onto Autozone.com and sign up for their online repair. It is free to use but you have to register.

Nov 16, 2010 | 1997 Chevrolet Cavalier

1 Answer

I need the torque sequence for a 1998 chevy cavalier head


There's two engine's, your car could have, 2.2L or 2.4L. so here's both, cylinder head torque for 2.4L engine.
Step # 1
Bolt's 1 - 8 40 Ft.Lbs
Bolt's 9 - 10 30 Ft.Lbs

Step # 2
All bolt's additional 90deg.

Hope this was very helpful.

cb3ba1f.gif
9568cea.gif

Sep 02, 2010 | 1998 Chevrolet Cavalier

1 Answer

Engine torque specs for 1996 chevy cavalier 2.2l


For 1996 Chevrolet Cavalier 2.2L SFI OHV 4cyl the check the next Head Bolt Torque sequence...

------------ front | 8 4 1 5 9 | of | | engine | 7 3 2 6 10 | ------------

Step 1: torque long bolts 8,4,1,5, & 9 to 46 Ft/Lbs torque short bolts 7,3,2,6, & 10 to 43 Ft/Lbs
Step 2: torque all bolts an additional 90 degrees Recheck final torque in sequence

*** CAUTION *** engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.

Hope helps (remnember rated this).

Jul 15, 2010 | 1996 Chevrolet Cavalier

1 Answer

I have 2001 chevy cavilier with the 2.2 liter motor I had to replace the camshaft and the lifters and need to know the torque ratio for the bolts on the head


the long bolts (along the backside/intake side of engine) should be torqued to 63Nm (46ft/lb)
the shorter ones (4 bolts along the front/exhaust side and the stud at the end that's attached to the trans) need to be torqued to 58Nm (43ft/lb) with the pattern of:
(pully 8 4 1 5 9 <-- long bolts @ 63Nm (46ft/lb)
side ) 7 3 2 6 10 <-- short bolts / 10 is the stud @ 58Nm (43ft/lb)

give each an additional 90° (¼) turn

it's best to do the tightening in stages, you don't want to go completely tight on the first pass or there will problems and you'll get to do it all over again

Nov 21, 2009 | 2001 Chevrolet Cavalier

1 Answer

I blew the head gasket on my 2002 Chevy Cavalier 2.2 L OHV. I am needing to know the torque specs so that I can have the gasket replaced tomorrow! A picture would be wonderful! Uncle is going to fix it but...


When torquing items today very little is done with just "numbers" in the process. Now you have to have an angle meter to complete the process so when you see me say to torque a specific number "plus so many degrees", this is how it's done. This is the meter:df03f54.gif Now, Here are the specs for installing the head:
Cylinder Head Bolt
  • First Pass
30 N·m
22 lb ft
  • Final Pass
155 degrees


Here is the sequence shown in picture form:
e8f4606.gif Also, you will need to discard the old bolts because they are "torque to yeild" bolts and CANNOT be reused. The reason: "Torque to yeild" bolts actually stretch during the torque process and once they've gone through this process they can't be reused because they no longer are able to "clamp" the head because they are too long. Hope this helps your repair project.








Oct 10, 2009 | 2002 Chevrolet Cavalier Coupe

1 Answer

Torque specks


hi 1999 chevy malibu head bolts 1-8 40 ft lbs bolts9-10 30 ft lbs tighten all bolts an additional 90 degrees

rod bearings 18 ft lbs plus additional 80 degrees

head
top row of bolts 9 3 1 5 7 bottom row 10 6 2 4 8 from left to right

Feb 12, 2009 | 1999 Chevrolet Malibu

1 Answer

Need to know cylinder head bolt torque specs


Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Feb 07, 2009 | 1994 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
1998 Chevrolet Cavalier Logo

173 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...