Question about 2005 Buick LaCrosse

2 Answers

My low beam lights wont work, either on auto or manual. The two low beam fuses are ok. I cant get a voltage reading at the fuses. Do I have to go to factory default settings? I've looed at the bulbs and they both look ok. thanx joe

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

My low beams headlights arent working and my fuses are perfectly fine... Any solutions??
2005 buick lacrosse

Posted on Sep 11, 2011

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

There is a small part called a dim light sender. It is kind of like a fuse. It plugs in and out and is about $20.00. Installing the dim light sender corrected the issue in my car. It was bad because I drove it on a dirt road and it was bumpy.

Posted on Oct 15, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 Saturn aura wont start after trying to put rt.low lowbeam replacement


On the inside of the lid is a diagram .
The headlamps may be turned ON 2 different ways. First, when the driver places the headlamp switch in the HEADLAMP position, for normal operation. Second, with the headlamp switch placed in the AUTO position, for automatic lamp control (ALC). During ALC, the headlamps will be OFF in daylight conditions, or low beam operation in low light conditions. Battery positive voltage is supplied to the low beam relay and the high beam relay in the underhood fuse block. When low beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the low beam relay. This activates the relay and the relay supplies voltage to the left hand low beam headlamp through the LH LOW BEAM fuse and to the right hand low beam headlamp through the RH LOW BEAM fuse. Ground for the left hand low beam headlamp is provided at G101. Ground for the right hand low beam headlamp is provided at G102. When high beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the high beam relay. This activates the relay and the relay supplies voltage to the left hand high beam headlamp through the LH HIGH BEAM fuse and to the right hand high beam headlamp through the RH HIGH BEAM fuse. Ground for the left hand high beam headlamp is provided at G101. Ground for the right hand high beam headlamp is provided at G102.

Aug 14, 2017 | Saturn Cars & Trucks

1 Answer

No dims, just brights? Need lights or fuse? Is there more fuse boxes than the one under the hood?


Have you tried operating headlamps in manual mode, not automatic? Do they work correctly in manual mode?
You have a low beam fuse in under hood fuse box. With headlamps on, low beam, any voltage at that fuse circuit? Even if the fuse is good, if no voltage on fuse circuit, the circuit is still dead.
Any applicable trouble codes? Some of the national brand auto stores will check codes for free.
My info shows second fuse box under rear seat.

Nov 30, 2015 | 2005 Chevrolet Chevrolet TrailBlazer EXT...

1 Answer

Low beam lamp(s) fault detected 2014 kenworth no low beam lights


First check light relay fuse, if ok check battery voltage at low beam light terminal, if ok replace low beam bulb, if no voltage check switch side of relay, if voltage replace relay, if no voltage check headlight low beam switch.

Jun 26, 2015 | Cars & Trucks

1 Answer

2002 rendezvous low beams don't work. Fuses and bulbs fine. High beams work. Even swapped relays with high beams still no change. Running lights work but low beams don't in auto or manual. What else can...


What about the rest of the lights. The Auto and Manual function should turn the tail lights also. If they work, then it is a headlight wiring problem. If the tail lights are not working either, then it is the auto control module

Nov 14, 2014 | 2002 Buick Rendezvous

1 Answer

No power to right side (PS) headlight low beam plug socket, new bulb, fuse is good. High beam works, blinker works, park light works. just no low beam and doesn't register any voltage on volt meter.


check low beam fuse when switched on if it has voltage registering across the fuse ,if there is voltage across the low beam RHS fuse then it is possibly a pinched wire from the headlight running back towards inside of the car

Jan 30, 2014 | Cars & Trucks

1 Answer

Low beams dont turn on........... bulbs check ok...................fuses under hood ok.............need help


{: ) I wonder how you checked the fuses and the bulbs. Did you check also the HDM fuse 15amp and the HDM relay both at the underhood fuseblock? Turn on the low beam and check for 12v at the LO beam fuses. If there is voltage at the fuses but the low beam ok bulbs won't light, then there's a wiring issue from your fuseblock going to the bulbs.
But if no voltages on the LO fuses when the low beam is switched on, then the problem could be on the HDM fuse or relay, the headlamp switch, the BCM, or even the fuseblock.

Jul 02, 2011 | 2006 GMC Envoy

1 Answer

Low beam dosent work. bulb is good highbeam works cant find fuse for lights. its not underhood


Hi,
It has been because the lamp bulb or halogen lamp module has reached the end of its serviceable life, not because of any wiring problems. Low beam burns out first because it is on the most. If low beam is lost simultaneously in both headlights, I would check fuse first, then the headlight switch. If low beam is lost on one side only, it is almost always going to be due to the bulb or lamp module needing to be replaced. In that case, replace them in both headlights because the other one will be going kaput in short order, as well.
Most like the low beam filiment is bad but the high beam filiment is still good, try replacing bulb. If replacing bulb does not fix problem then you probably have voltage problems and should check the voltage reading and the plug.
OR
isolate the wire that comes from the headlight switch to the headlamp bulbs for low beam and check to see if there is a short in the wire. You can find this wire by using a test light turn on the key and get a good ground with the test light poke the wire and see if the test light illunimates with the headlight switch on.
check the wires, and check the fuse for your lowbeams. could of blown a fuse on your lows, but your highs will still work.

The fuse box is located in the engine compartment,on the driver's side. Has thumb-screw retained cover.
Thanks for contacting fixya.com

Nov 07, 2009 | Dodge Ram 1500 Cars & Trucks

1 Answer

My headlights dont work,.all other lights are fine though,.is it the fuses or the bulbs? im not sure what fuses they would be,.there seem to be different ones for the same thing


do your flash to pass lamps light when you pull the stalk towards you? If yes, the bulbs are ok.
Do the hig beams work?
Your headlamps have sepaerate fuses for each headlamp and you have a low beam relay and a high beam relay under the hood in the black box.
If everything is out, I suspect a bad headlamp switch.
Check car-part.com and look on page with * for cheapest price.

Your owner manual will identify fuses & relays.

PS, You did not recently instal high current bulbs did you? If yes, put originals back in.

HEADLAMPS

The voltage is supplied to the lamp switch through a fuse. This fuse is located in the central junction box in the left-hand footwell.
When the headlamps are switched on, a voltage is supplied to the high beam/low beam switch and to the low beam relay. The relay for the low beam is located in the battery junction box (BJB) in the engine compartment.
If the high beam/low beam switch is set to "low beam", then a voltage is supplied through the low beam relay to the low beam part of the headlamp assembly. The left and right-hand low beams are fused separately. The fuses are located in the battery junction box (BJB) in the engine compartment.
If the high beam/low beam switch is set to "high beam", then a voltage is supplied through the high beam relay to the high beam part of the headlamp assembly. The left and right-hand high beams are fused separately. The fuses are located in the battery junction box (BJB) in the engine compartment.

----------------------------------------------------------------------------------------------------------
Lamp Switch
Removal
  1. s2y~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
    Remove the lower driver's side footwell trim.
  1. Detach the lamp switch bezel.
    • Remove two screws.
  1. Remove the light switch.
    • Remove three screws.
    • Disconnect the electrical connector

Feb 23, 2009 | 2005 Ford Focus

1 Answer

2005 honda odyssey no low beam headlights


DIMMER SWICH, PROBABLY, WHICH IS INCORPERATED IN CONTROL ON STER. COLUMN?

Oct 08, 2008 | 1995 Honda Odyssey

4 Answers

Low beam headlights do not work, but high beam headlights do


Clyde,

I've been troubleshooting this same problem on a different vehicle this week, and I can give you the steps I'd take.

1. If both sides went out at the same time, the problem is *NOT* likely to be the bulbs.

2. Check the fuses to see if both low beam lights are on the same fuse. Many cars have one fuse for low beam and another for high beam, so both lights out at the same time typically means fuse blown.

3. If the headlights are OK and the fuses are OK, then the problem is *LIKELY* the headlight switch. In my case, AutoZone has one and it can be installed easily; but in your case, that may not be as simple.

Please post your findings or comments.

Jul 16, 2008 | 1991 Nissan Pickup

Not finding what you are looking for?
2005 Buick LaCrosse Logo

1,019 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

79851 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...