Question about 1995 Chevrolet Corvette

2 Answers

The windshield wipers aren't working. Ground wire is good.

Posted by on

  • 2 more comments 
  • vicki gentry Aug 14, 2008

    i am having a problem with my wipres too. for a while it was like they had a mind of there own when you turned them on. they seemed to go their own speed or would stop while the switch was turned on. Now they have completly stopped working and this is not good cause we are having a lot of bad weather where i live. can anyone please help me. I have replaced the fuse and that did nothing.

  • JrJuug Dec 02, 2008

    I HAVE THE SAME PROBLEM HOWEVER JUST ONE IS NOT WORKING THE PASSENGER SIDE...I BELIEVE I MISSING A PIECE BECAUSE IT WAS TIGHTENED BEFORE BUT STOPPED WORKING AGAIN HELP ME!!!

  • rslagle43 Dec 11, 2008

    where is the fuse located, I checked the fuse block and none of them are marked windshield wipers? Please help

  • gordonparsle Feb 15, 2009

    Windshield wipers won't work.

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 375 Answers

If you turn them and open hood and can hear the wiper motor running then something is stripped in the gearing, not very common. Otherwise check for power getting motor by unplugging motor and use test light.

Posted on Aug 03, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

There is a 2X4" circuit board to control the wiper motor. Its less than $20 on-line. You will need torx head screwdriver to replace it.

Posted on Feb 18, 2009

3 Suggested Answers

tommyboinow
  • 324 Answers

SOURCE: rear windshield wiper stopped working, its not the fuse

then it has to be the switch or the motor.

Posted on Nov 26, 2008

  • 840 Answers

SOURCE: Rear Windshield Wiper Problems

Check the wiper motor connection if its touching anything and loose it will automatically ground out and check at connection make sure you put some gel and then snap it in/ Please rate my response thank you very much

Posted on Jan 31, 2009

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My windshields wipers wont work


If that happens, your windshield wipers will not work at all and you won't be able to clear any water, dirt, or snow that ends up on your windshield. Replace the windshield wiper motor right away. The windshield wiper fuse is burnt out. When the windshield wiper motor is overloaded, the fuse burns out.23 Nov 2015

Top 5 Reasons Your Windshield Wipers Aren't Working - YourMechanic

https://www.yourmechanic.com/.../top-5-reasons-your-windshield-wipers-aren-t-workin... https://www.google.co.uk/webhp?sourceid=chrome-instant&rlz=1C1CHBD_en-GBGB719GB719&ion=1&espv=2&ie=UTF-8#q=My+windshields+wipers+wont+work

Dec 12, 2016 | Cars & Trucks

1 Answer

2003 Pontiac Montana wipers not working how to fix


First you need a wiring diagram, free at http://www.bbbind.com/free_tsb.html Then you need a DVOM - digital volt ohm meter to test the circuit . Then if your not familiar with automotive electrical systems testing ,go on youtube an check out Electric Testing Techniques You Need to Know Also having a factory diagnostic trouble shooting chart would also be usefull . You could just start replacing parts , you mite get lucky . The wiper motor is a high fail part , so is the switch ..You could find the fuse is blown ! But fuse's don't usually blow without a reason . Short to ground , low resistance . ( high current flow) Also knowing how they work and what all is involved in making them work.
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Windshield wiper motor module
• Windshield wiper motor
• Windshield washer pump motor
• FRT/WPR/WSHR 25A fuse

Wiper/Washer System Operation
The windshield wiper motor module is part of the windshield wiper motor cover and controls wiper motor operation. The windshield wiper motor is a 2 speed motor and is operated at low speed in all modes except HIGH. The accessory voltage supply circuit to the windshield wiper motor assembly is used to operate the wiper motor in all of the low speed modes. The accessory voltage supply circuit to the windshield wiper/washer switch is used to supply the windshield wiper switch signal circuits and the wiper motor high speed circuit.
When the wiper/washer switch is in the LOW position voltage is supplied through a 24K ohm resistor within the switch to the windshield wiper switch signal 2 circuit, and accessory voltage is supplied to the windshield wiper switch signal 1 circuit. The reduced voltage from the wiper switch signal 2 circuit and accessory voltage from the wiper switch signal 1 circuit causes the wiper motor module to close the wiper motor accessory voltage supply circuit to the wiper motor low speed terminal.
Windshield wiper/washer system MIST operation is identical to LOW operation except that the MIST switch is a press and release type. When the wiper switch is moved to the MIST position and released, low speed wiper motor operation is started and will continue until 1 cycle is complete. If the wiper switch is moved to the MIST position and held, the windshield wiper motor will operate in the LOW mode until the switch is released.

Don't the wipers work in any mode ?
1
Did you review the Wiper/Washer System description and operation and perform the necessary inspections?
YES - Go to Step 2
NO - Go to Symptoms - Wiper/Washer Systems
2
Turn ON the ignition , with the engine OFF.
Operate the windshield wiper/washer switch through all the switch positions.
Does the windshield wiper/washer system operate normally?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Turn OFF the ignition.
Disconnect the harness connector of the windshield wiper motor.
Turn the ignition ON, with the engine OFF.
Connect a test lamp from the accessory voltage circuit of the windshield wiper motor to a good ground.
Does the test lamp illuminate?
YES - Go to Step 4
NO - Go to Step 13
4
Connect a test lamp from the accessory voltage circuit to the ground circuit of the windshield wiper motor.
Does the test lamp illuminate?
YES - Go to Step 5
NO - Go to Step 14
5
Connect a test lamp from the signal 2 circuit of the windshield wiper switch to a good ground.
Press the windshield washer switch.
Does the test lamp illuminate?
YES - Go to Step 11
NO - Go to Step 6
Let me know if you make it this far and i will send rest of diagnostic's

Nov 25, 2016 | 2003 Pontiac Montana

2 Answers

Windscreen wipers not working


WINDSHIELD WIPERS


It can be faulty wiper motor or blown wiper control fuse.


Do you hear any kind of noise when you starter the wiper function. If yes then fuse is ok, but issue is wiper motor.

If no movement at all and no noise then its blown fuse or shorted/loose wiper control wiring: -----

For complete troubleshooting i suggest you a helpful link with accurate solutions.

-------------

Click the link below: -------




http://alltypesofpartsreplacing.blogspot.com/2012/12/windshield-wipers-windshield-wipers-not.html

--------

These will help.

Thanks.

Dec 09, 2012 | Cars & Trucks

1 Answer

My windshield wipers quit working. getting juice to one of the 3 wires.


one wire will be power one wire will low speed wiper and one wire will be high speed wiper.you need to check the grounding of the wiper motor.if you take a jumper wire and attach one end to the battery, or a good ground at the motor or somewhere and the other end then make good contact to the body of the wiper motor and it should work,if it does then you need to permantly hook up a ground wire to the wiper motor.this was a common problem.

Mar 08, 2011 | 1978 Chevrolet Chevette

3 Answers

Windshield wipers stopped working not fuse is there a relay and where is it


with the key on and the wiper switch in the low or high position tap the wiper motor with a screwdriver handle. If it starts working replace the wiper motor.

Sep 26, 2010 | 2002 Buick Rendezvous

1 Answer

My windshield wipers don't work but the rear wipers and washer works..do I need to replace the wiper motor? If so, where is it located and how do I replace it?


Check fuses, front and back wiper motors run on different fuses. Test for power and ground at front wiper motor wires. If you have power and ground there your wiper motor may be toast. Good luck

Sep 12, 2010 | 1997 Mitsubishi Montero Sport

1 Answer

Windshield wipers don't work.Fuse is good and motor is good.No power to motor. The tag to tell what relay is for what is missing. Was wondering if the wipers had a relay and which one it is.


Hello Firerocker.
If your washer motor works there is power in the circuit and ground.
The wiper motor housing needs to be grounded.
If neither one works check for power on the green wire leading into the motor. If nothing there your switch may be bad.
If there is power to the green wire then check for power on the gray wire on low wiper speed and power on purple on high speed.
Here is a diagram if you need it.

http://i28.photobucket.com/albums/c227/Kiltylake/Wiper.gif

Hope this gets your wipers going again.

KL


Feb 12, 2010 | 1992 Buick LeSabre

2 Answers

Rear Windshield Wiper Problems


Check the wiper motor connection if its touching anything and loose it will automatically ground out and check at connection make sure you put some gel and then snap it in/ Please rate my response thank you very much

Jan 31, 2009 | 2003 Chevrolet Tahoe

Not finding what you are looking for?
1995 Chevrolet Corvette Logo

Related Topics:

385 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

67911 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22011 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6817 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...