Question about 2004 Dodge Ram 1500

1 Answer

04 ram 1500 with shimmy when braking. - 2004 Dodge Ram 1500

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Sounds like the rotors are warped wheels need to be torqued when putting them on.

Posted on Mar 23, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What's wrong with the front end of my truck?


caliper malfunction brake fluid leak onto the pads causing it to slip and smoking from the brake fluid burning

Jul 06, 2014 | 2005 Chevrolet Silverado 1500 2WD

1 Answer

Truck shimmies when brakes applied


Check your brake rotors,are they worn even and no worn marks.When replacing,do both.

Jan 17, 2013 | 2003 GMC Sierra 1500

1 Answer

What makes a front end shake on a 2004 GMC Sierra 1500 4X4?


FRONT END SHIMMY AND SHAKING COULD HAVE A TIRE OUT OF BALANCELOOSE OR WORN WHEEL BEARINGS, WORN OUT BALL JOINTS,WORN OUT TIE ROD ENDS, FRONT END NEED ALIGNMENT.BRAKE ROTOR WORN OUT OR WARPED, MANY THINGS WILL CAUSE FRONT END TO SHAKE SHIMMY.

Aug 09, 2011 | 2004 GMC Sierra 1500 Crew Cab

1 Answer

2006 chevrolet 1500 brakes shimmy without touching them,also when setting still mash couple times let off ,wheels hard to turn


check for front brake calipers dragging, if the are replace calipers and front brake hoses, if calipers ok replace master cylinder, This is how to check calipers, jack up front of truck have some one apply brakes and release as soon as they release the brake peddle the wheels should spin freely if not brake the brake line lose at master cylinder if wheels spin free with line loose replace master cylinder, if not replace calipers and hoses.....HOPE THIS HELPS

Nov 16, 2010 | 2006 GMC Sierra 1500 2WD

1 Answer

2004 Dodge Ram 1500 Hemi Brake and ABS lights come on and speedometer does not read properly.


i just had the same problem w/ my 04 ram.......after replacing the sensors that the abs computer codes gave me it still had the same problem....then i unplugged the abs module only to find water in it.....apparently its a problem w/ dodge.....i dried it out with an air hose and it works fine now... hope this helps.......Chip

Sep 01, 2010 | 2004 Dodge Ram 1500

1 Answer

2007 DODGE RAM 1500 CASTER ON RIGHT SIDE WONT COME INTO SPEC GETTING SOME SHIMMY?? truck has 95,000 miles was last aligned with about 40,000 miles after a tire blowout and a bent rim alignment was...


The actual caster spec is not very significant - the handling is what counts. The caster will not cause a shimmy. Shimmy could be caused by tire problems, worn or damaged steering or suspension parts, bad shock absorbers or a bent wheel. As long as the vehicle does not pull and the handling is satisfactory, the caster is OK, If the tires are not wearing and the vehicle hamdles OK - don't worry about "specs." I have done a LOT of alignments where the readings did not match the specs, but the result was satisfactory.

Oct 25, 2009 | 2007 Dodge Ram Truck

1 Answer

Speedometer when crazy


my 99 had a sensor go bad that had similar symptoms. sensor is in rear "pumpkin". mounted on top. $41 at autozone. look at dodge truck forum, do a search.

Jun 19, 2009 | 2004 Dodge Ram 1500

1 Answer

04 dodge ram 1500 HEMI's new brake pads won't fit


what you need to do is line clamp brake hose so you dont push dirty brake fluid back into your system..(you can use a pair of needle nose visegrips if you dont own an actual line clamp) loosen bleeder at this point, remove caliper from attatching bracket, with old pad still installed next to piston use a big C-clamp to compress piston, just make sure clamp is centered and compress slowly allowing brake fluid to escape through loosened bleeder... once compressed tighten bleeder and install caliper and pads remove lineclamp....******NOTE******* no need to bleed the system cause of lineclamp procedure... Make sure upon reassembly you use plenty of brake lube on all sliding caliper parts...Good Luck

Dec 31, 2008 | 2004 Dodge Ram 1500

1 Answer

DASH BOARD SAYS LAMP OUT


one of the light isnt working...a turn signal, brake lamp, taillamp....one bulb will do it

Nov 17, 2008 | 2004 Dodge Ram 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...