Question about 1995 Nissan Quest

1 Answer

Sliding door handle need replacing - 1995 Nissan Quest

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 1 Answer

Go to junk yard,find a part and replace it
or go to rockauto.com

Posted on Aug 11, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing the exterior front door handle


Door handle fasteners are accessed from inside the doors so you need to remove the interior door panels. The door handles are then usually held on by clips or slides which are rather awkwardly positioned behind the door structure.

Mar 04, 2011 | 1999 Toyota RAV4

1 Answer

Need to replace inside door handle that broke completely off. How do I replace this section?


you will need to remove the cover around the handle they are easy to brake from the inside of the outside cover ring go from the inside with a small screw driver and slide between and pry the cover up it has 4 mounting points top left top bottom right and left.
next pop off the switch from the front slide a screwdriver at the front leading edge and push it towards the back of the door panel and lift gently there is a flange on the rear of it that holds the rear of the assembly down dont pry up on the back lift the front and slide it forward unplug all the wires. remove the two screws inside the door arm rest where you pull the door shut. the cup to close the door. next you need to remove the mirror cover at the front top of the door panel slide a screwdriver pry
straight out. using a door panel clip tool. slide under the panel at the bottom rear corner to find the clip and pry the clip out of the hole. work your way around the door to each clip. sometimes you can pull the panel off with your hands but if you are not experirenced you might break some clips or the door panel be nice to it dont break things. all the way around the sides and the bottom are released then pull away from the door and hold the bottom and lift up and hit the top of the door handle with your hand so the clips will release accross the top. remove the light socket from the rear bottom of the door. place the panel somewhere so you dont scratch it up. now remove the rivet from the handle. I punch the center out then use a sharp chisel to punch it off. you may want to drill the rivet. up to you. then the handle slides forward and you have to disconnect the linkage clips from the handle. install the new handle make sure the lock rod is in the hole that slides the lock. hook up the linkages new slide back in position and rivet then reverse the prosess of removing the handle

Dec 12, 2010 | 1999 Chevrolet Suburban

1 Answer

How do I remove the driver side door panel?


door panel pulls straight out or slides, it is held on by plastic mollies they may break when you take it off be very careful not to break them but you can get replacements if needed. check Chevy dealership. there is also one or two screws one at handle, door panel should slide past door handle at angle.

Feb 16, 2010 | 1998 Chevrolet S-10 Pickup

1 Answer

I have taken the door panel off of my '98 GMC Sierra to fix my door handle, which does not work anymore. It has no resistance against it, and moves side to side without even trying to open the door. When i...


Broken inside door handles are a common problem and there is not an easier way of fixing problem.drill out head of rivet with a 3/16 drill bit.Then slide handle assy. from panel.To install new handle attach the two rods you removed .Then slide new handle back into the slots and replace the rivet.

Aug 06, 2009 | 1998 GMC Sierra

1 Answer

Broken door handle - 2001 Nissan Quest SE


first you van order parts at discount from tascafordparts.com.
quest & mecrury villager are the same vehicle made at the same assembly plant. good luck to all. If you were in detroit area, I wold help you.

Trim Panel —Sliding Door Removal
  1. Remove the sliding door trim panel finish panel.
532ac84.gif 2. Remove the sliding door trim panel 2965fbe.gif Latch Remote Control —Sliding Door Removal
  1. Remove the rear sliding door trim panel. For additional information, refer to Section 501-05 .
  1. Position the watershield aside.
  1. If equipped, disconnect the sliding door power door lock actuator electrical connector.
f373e91.gif
  1. NOTE: Mark the position of the sliding door rear latch cable adjusting bracket before removing the bolt.
  2. Disconnect the sliding door rear latch cable.
  3. Remove the bolt.
  4. Remove the sliding door rear latch cable adjusting bracket from the latch remote control.
  5. Disconnect the sliding door rear latch cable from the latch remote control.
b8f2f32.gif
  1. Remove the 4 sliding door front latch bolts.
NOTE: If necessary, transfer parts to the new sliding door latch remote control.
Remove the sliding door latch remote control.
  1. Remove the bolts.
  1. Remove the sliding door latch remote control.
cb5ee71.gif
Handle —Exterior, Sliding Door Removal
  1. Remove the sliding door latch remote control. For additional information, refer to Latch Remote Control—Sliding Door .
  1. Remove the sliding door exterior handle.
    1. Remove the nuts.
    1. Remove the sliding door exterior handle.
0c820f3.gif

Mar 08, 2009 | 2001 Nissan Quest

2 Answers

Mazda 5 replacing external handle on sliding door


Your door should be held on with clips. Removing the panel is sometimes hard, just take a good WIDE flat head screwdriver, and whatever tool needed to remove the screws holding the panel on, and be careful. Check underneath the panel, by the inside handle, and the arm point for screws. Once removed, take your WIDE screw driver, and don't quite pry them off, more or less try to get it underneath and pull towards yourself. There is no real easy way, just try to be patient with it, and if you hit any binds, look for more screws, its just a matter of patience for sure.

Feb 13, 2009 | 2006 Mazda 5

1 Answer

Broken handle on sliding door behind driver


First get vin call toyota parts dept/ get the part its really easy to put in look for screws in little pop ups take screws out then go from the bottom of the door and lift out then go side do the same thing then lift from bottom of door and upward then you will take of vapor or plastic sheet then you just replace the handle thats it then out it back together/ Please rate my response thank you very much

Dec 28, 2008 | 1999 Toyota Sienna

1 Answer

Replace side door handle assembly


Remove the snap ring from under the inside door handle and plate (a rag around the base of the handle and a left-right tug on the rag may loosen it, or look under it & pry the snap ring off with a small hook tool

Remove the door lock knob bezel; remove the screw & slide it rearward

Remove the door trim; Remove the two clips; slide a thin, flat wide tool under the panel and pry towards you, there are 8 clips to dislodge

Pull the door trim straight up once all of the clips are loosened.

Easy.

Sep 23, 2008 | 1992 Toyota Previa

2 Answers

Outside sliding door handle?


Yes. It is a difficult job, but not impossible. The hardest part is actually removing the interior door handle. Here are the steps.
  1. remove the interior door handle by pressing the door panel in and prying out the C-ring retainer clip
  2. remove the lock slide switch bezel with 1 screw, then insert a blade on the bottom left of the slider between the slider and bezel, and release the clip, the slide the bezel toward the rear of the vehicle and pull out
  3. carefully unclip the door panel around the lower edge and sides and lift the door panel UP and off
  4. remove the interior lock slide switch with 2 screws
  5. pull back the plastic vapor shield part way to expose the mechanism
  6. there is a cable that runs from the mechanism to the exterior handle, unclip it from the door frame
  7. there is a rod that drops down from the door handle to the mechanism, release the rod from the plastic clip
  8. locate a large (likely black phillips) screw next to the door handle on the EDGE of the door, remove it
  9. locate a 10mm screw on the inside behind the door handle, remove it
  10. locate the final 10mm screw behind the handle through an access hole, remove it (careful not to let it fall inside the door)
  11. the door handle will push out through the door part way- there is another C-clip securing the lock cylinder that will need to be removed, and the lock cylinder can be pushed into the door cavity
  12. pull the door handle through the outside of the door skin- the door handle assembly is still attached inside the door by the latch cable- the cable can be easily removed from the handle assembly to remove it completely
  13. you will likely find that the end of the door handle itself is broken off- don’t buy a new handle! Email me and I will show you my free and possibly better solution that will likely last the life of the vehicle dbonnell1972 at yahoo dot com
re-assembly is the reverse of the removal

Aug 13, 2008 | 1994 Toyota Previa

1 Answer

2033 kia sedona sliding outer door handle


take inside door pannel of,gently remove plastic sheet,and you will see door handle,un clipdoor lever and nuts,

Jul 12, 2008 | 2003 Kia Sedona

Not finding what you are looking for?
1995 Nissan Quest Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...