Where can i get intructions on how to install a window motor and regulator driver side

REMOVAL PROCEDURE:
Remove the window.

• Disconnect the power window motor electrical connector, if equipped.
  
• Remove the electrical harness retainers, if equipped.
  
• Drill out the rivets that secure the window regulator to the door.
  
• Remove the window regulator from the door.
  
• Remove the power window motor, if equipped.
  

INSTALLATION PROCEDURE:

• Install the power window motor, if equipped.
  
• Install the window regulator to the door.
  
• Install the rivets that secure the window regulator to the door using J 34940.
  
• Connect the electrical connector, if equipped.
  
• Connect the electrical harness retainers, if equipped.
  
• Install the window.
  

You have to remove the inner door panel to
access the window regulator

You remove the regulator & then the motor from it

You Tube Video will provide a visual of several
similar window motor replacement jobs

Go there-- enter your car,question ,details,etc--- then move
around the site to watch various things

Motor Replacement - Power Window

Removal Procedure
Be very careful
Hope this helps




Caution: Do not attempt to service the regulator motor withoutreleasing the counterbalance spring tension. The regulator lift arm isunder tension from the counterbalance spring and can cause personalinjury if the motor is removed from the regulator.

1. Remove the window regulator.

1. Drill a hole through the window regulator and the sector gear.

1. Install a bolt and a nut through the hole in order to lock the sector gear in position.
2. Drill out the rivets that secure the power window motor to the window regulator.
3. Remove the power window motor from the window regulator.

Installation Procedure

1. Install the power window motor to the window regulator.

Important: Remove the nut and the bolt that were used in order to secure the sector gear in position.

1. Install the rivets in order to secure the power window motor to the window regulator.
2. Install the window regulator.

Please don't forget to rate! Thanks!!!

Motor & Regulator

1. Remove the front or rear carrier assembly.
   
2. Slide a hammer handle between the window guide and carrier assembly until the hammer handle end presses on the gears of the carrier assembly.
   
3. Unfasten the bolts (1) and remove window regulator.
   

Unfasten the bolts (1) and remove window regulator

To install:

NOTE:By removing window regulator motor, gearing shifts, it is not centered

1. When installing window regulator motor, the gears must be aligned until the window regulator motor is centered again.
   
2. Attach and tighten the bolts to 3.5 Nm. The bolts must be tightened to specifications, or damage to plastic sleeve on window regulator motor can result.
   
3. Carrier assembly with window regulator, installing:
   
   • For replacement part carrier assemblies, the gearing is secured in place with a cable tie.
     

For replacement part carrier assemblies, the gearing is secured in place with a cable tie (1)

Slide a hammer handle between window guide and SF so far until hammer handle end presses on gears of SF.

Remove the cable tie .

By removing window regulator motor, gearing shifts, it is not centered.

When installing window regulator motor, gears must be aligned until window regulator motor is centered again.

Attach and tighten bolts to 3.5 Nm. The bolts must be tightened to specifications, or damage to plastic sleeve on window regulator motor can result.

// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 23; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos';

THERE WILL BE 2 10mm NUTS THAT HOLD THE GLASS TO THE REGULATOR, REMOVE THOSE. THE REGULATOR IS HELD ON BY THE WINDOW MOTOR, THERE IS 4 RIVETS HOLDING THE MOTOR GRID THOSE RIVETS AND THE MOTOR AND REGULATOR WILL COME OUT. REPLACE MOTOR AND REGULATOR INSTALL 4 RIVETS SIZE 1/4" DIA GRIP RANG 032" AND ATTACH WINDOW WITH NUTS TO REGULATOR.

Try the fuse. The switch may be faulty so check by removing the inner door panel and connecting a 12v battery via two wires to the motor that winds the window up and down. If it goes up and down it's probably the switch which may just need a clean on the terminals.

Power Window Motor: Service and Repair
REMOVAL
1. Disconnect and isolate the battery negative cable.
2. Remove the window regulator from the door.
3. Place the window regulator on a suitable work surface and remove the screws that secure the power window motor to the window regulator.
4. Remove the power window motor from the window regulator.
INSTALLATION
1. Position the power window motor onto the window regulator.
2. Install and tighten the screws that secure the power window motor to the window regulator. Tighten the screws to 9 Nm (80 in. lbs.).
3. Install the window regulator onto the door.
4. Reconnect the battery negative cable.

You'll need to buy a new motor and regulator. You can go used or new, it's up to you. The regulator will include the cable.

- Remove the interior door trim,
- Disconnect the power cable from the window motor,
- Remove the window bump-stops (one at the front, one back),
- Remove the glass window from the regulator (two bolts),
- Slide the glass window out of the top of the door,
- Remove 3 nuts from the window motor,
- Remove all window regulator bolts,
- Slide the motor & regulator assembly out the top of the door.

- Mount your new motor to your new regulator,
- Install the new motor & regulator assembly in the reverse order.

1. Raise and support the rear door window glass to the full up position.
2. Remove the interior door handle.
3. Remove the rear door speaker.
4. Remove the water shield.
5. Disconnect the rear door window regulator motor electrical connector.
6. Remove the rear door window regulator rivets.
7. Remove the rear door window regulator by sliding the regulator arms off of the window glass track.
8. Installation is the reverse of the removal procedure, noting the following:
   • Cycle the door glass to make sure of engagement of the drive mechanism.
   • Remove the rear door window glass-to-regulator bolt or rivet.
   • Position the rear door window glass as necessary to access the rear door window glass-to-regulator rivet.
   • Secure the rear door window glass in the full UP position with tape.
   • Disconnect the window regulator motor electrical connector.
   • Remove the 2 window regulator nuts.
   • Remove the 3 window regulator motor bracket nuts.
   • Install the window regulator assembly. Tighten the 3 motor bracket nuts to 89 inch lbs. (10 Nm).
   • Install the 2 window regulator nuts. Tighten the nuts to 89 inch lbs. (10 Nm).
   • Connect the window regulator motor electrical connector.
   • Remove the tape securing the rear door window glass in the full UP position.
   • Position the rear door window glass as necessary to access the rear door window glass-to-regulator rivet. Tighten the bolt to 62 inch lbs. (7 Nm), or install a new rivet.
   • Install the window regulator motor
   • Remove the window regulator assembly.

Remove the window regulator motor

I had the same problem with the driver's side front and rear windows. Had to replace the motor assemblies.