Question about Ford Explorer Sport

1 Answer

Brake peddle jumping back when prested on funny kind of rumbling from the brake cylender

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,400 Answers

Peddle jumping is your anti lock brakes activating. Rumbling could be anti lock recycling or your brakes are grinding and need replacing

Posted on Mar 23, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The clutch pedal seems to be very flopy and is not going into gear easily


Can be broken spring on the cluch pedal in side the car, that hold the pedal all the way back for full amount of brake fluid to the slave cylender, can be checked by pulling the pedal all the way up before steping it to the floor and putting in to gear or just look up under the daschbord on the pedal. Can allso be to little brake fluid in container. To check the master cylender rubber, step on the pedal putt in gear with engine running and wait with pedal all the way to the floor, if the rubber is gone the car wil start to go after some time (1/2-1 min or less) To check the slave cylender rubber will be dune the same way and working same way but it will be leaking out and on the floor.

Jun 18, 2012 | 1999 SsangYong Korando

1 Answer

How do i know if the master cylender is bad


You run a line clamp test. All you need is 4 clamp tools to block off all brake hoses with light pressure. Push on brake peddle if it's hard back off and push slow and light. If stays hard master cylinder is good. Hold pressure and have someone remove. The clamps

Feb 01, 2012 | Cars & Trucks

1 Answer

Red brake light stays on


Many cars have a switch that rests on the arm for the brake peddle that self adjusts. If something gets stuck between the switch and the peddle it can adjust the switch too far way from the peddle arm. When the object that got in the way falls out or is removed the switch will no longer contact the peddle arm and the brake lights will stay on. You would probably need to remove the panel cover for the bottom of the dashboard to access the brake peddle are and brake light switch. Once you see the switch depress the peddle with your hand and push the switch toward the peddle are. It shouldn't be too hard to push back into place and will probably make a series of clicks as it moves. Once the switch has been pushed in release the brake peddle and the switch will adjust itself back to where it should be.

Mar 31, 2011 | 2006 Chrysler 300

1 Answer

Soft brake peddle on 1994 chevy 3/4ton truck is it the back adjuster?


You might have a leak in one of your brake lines i would look at all of the lines for a leak look at the brake drums for fluid driping out of the bottom if you dont find a leak it may be time for a brake job . a soft peddel means you have air in your system.From a leak or wore out pads or shoes or a leaking wheel cylender from wore out rear shoes . watch your master cylender to see if its low on fluid.

Aug 24, 2010 | 1994 Chevrolet C2500

2 Answers

How do you get the E brake off?


I don't know if I can explain this correctly but I'll try. Some cars that have a foot peddle that activates the emergency brake when foot peddle is compressed. If there is not a brake release handle directly above the peddle, it might have a kind of spring release. Try pressing down on the peddle hard and then move your foot off and out of the way and it might spring back and release that way.

Jul 26, 2010 | 1996 Cadillac DeVille

1 Answer

Clutch peddle will not mash. we replaced clutch, presser plate, throwout bearing and master cylender and hose to slave cylender and clutch peddle won't mash you can take slave cylender loose fro...


when you bleed the system you need to force fluid from the slave cylinder up threw the master cylinder . this is proper way to bleed clutch system.

Jul 02, 2009 | 2003 Hyundai Santa Fe

1 Answer

Dash lights come on when I press the brake peddle


Sounds as if your getting a back feed. Most likely from the brake light bulbs (part number 1157). Take out the brake light bulbs and see if the dash lights still come on when you step on the brakes. If so check the lead contacts on bulbs, sometimes they get squished/corroded and jump both contacts, replace bulbs with new and recheck. Hope this helps.

Sep 17, 2008 | 1990 Nissan Pathfinder

1 Answer

Brake light will not go off when foot is removed from brake peddle. Brake switch on master cylender has been replaced....


Sounds like the brake pedal is not coming up far enough from the floor after being pressed thus causing the switch to remain activated even though pressure is not applied to the brake at the time.

Aug 07, 2008 | Ford Thunderbird Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...