Question about 2003 Toyota Land Cruiser

1 Answer

I NEED TO GET THE AXLE OUT OF THE C.V. JOINT - 2003 Toyota Land Cruiser

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,510 Answers

You need a big vice and a big hammer! Move the boot out of the way, remove as much grease as you can from the housing, grip the shaft in the vice as tightly as you can at about 45 deg. and with the housing of the CV horizontal just below the jaws - and hit it. It sounds brutish, but keep hitting until the cv comes off the shaft, it is held in place by a pretty strong clip.

Posted on Mar 23, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change the front axle on a 2004 impala


You will need a large socket to fit the nut on the end of the CV axle shaft. You will also need a breaker bar to remove this nut. You will need a torque wrench capable of achieving the correct torque when replacing the nut on the replacement shaft. You will need a relatively heavy (3-pound) hammer and a pry bar to remove the axle shaft from the transmission housing. You should break the axle nut loose prior to raising the vehicle off the ground as it is very tight and may not come loose easily once raised. If you use an impact wrench then the need to do this before raising the vehicle is not as great. You need to raise the vehicle on jack stand(s). Remove the wheel from the side you are replacing. Remove the brake caliper and rotor assembly as well. Remove the axle nut. The axle must be pulled free of the hub spline by pushing it out backwards. This is not usually possible without either (1) separating the lower ball joint from the lower control arm, or (2) unbolting the lower control arm assembly from the subframe and pulling it outward and to the side.
Be careful when pushing and pulling on the axle shaft. The outer CV joint is fixed, but the inner joint can be pulled out too far and become separated. This will make removal much more difficult. Once you have freed the outer CV joint from the hub, then you need to use the prybar and hammer to tap the inner joint out of the transaxle. It snaps in place and will take a few attempts to achieve. Be careful if trying to pry on the transaxle housing as it is cast metal and can break easily. Once you have the inner joint free you can remove the shaft. There may be some transmission fluid leak from the seal when you remove the shaft. Insert the new shaft into the transaxle. Push it in to snap it into place. You can pull back about an inch or two to help get the force necessary to pop it in, but again be careful not to overextend the inner joint. Once the inner joint is in place, slide the outer joint back through the hub splines. Reconnect the ball joint/lower control arm. Replace the axle nut (use the one supplied with the new shaft. Torque to proper specifications. Replace the rotor/caliper/wheel.

Dec 26, 2014 | 2004 Chevrolet Impala

1 Answer

1991 ford tempo passenger axle how do I remove it


You will need to remove the passenger wheel and large nut holding the axle to the center of the hub of the spindle. Then remove the nut and un-seat the lower ball joint. Separate the lower control arm from the spindle and pull spindle out while pushing axle in, separate the spindle from the axle and tie aside out of the way. The axle is held into the trans-axle with a circlip, you will need to get a pry bar behind the inner CV joint and pop the inner spline joint out of the trans-axle.

Jul 09, 2014 | Cars & Trucks

1 Answer

Need to replace the cv joint boot on a 2000 buick century (outside)


First i think you should replace the cv axle instead of trying to just replace the boot, if the grease leaked out and dirt got into the joint then the joint is bad in soon you will hear noise or joint will let go. the time it take to replace the boot and the cost of the bbot i would replace the axle, you can buy a rebuilt axle for 45.00 with the exchange of the old one. heres directions to replace the boot. remove the wheel then remove the brake caliper and bracket, tie this of to side. take brake rotor off it should slide off, you may need to tap to break it free.next is to remove the center axle nut, after that you will remove the lower balljoint nut and split lower control arm from spindle, you may need a pry bar to sperate the control arm from the spindle, pull spindle out and slide axle out of the spindle.to replace the boot cut the inner and outter boot clamps, slide boot back and look inside for a clip., some use clip inside and some outside, look at shaft going into joint, see if theres a clip to open to slide cv joint out. if theres no clip then its an internal lock clip and what you need to do is hood the shaft and bang joint off shaft, you will need some help, hold the saft or use a pry bar and slide it into the rear of the inside joint between the back of the joint and the trany and give it a tug the joint will pop out of the trany this is a lot easier to work on off the car, put it in a vise, loock the shaft in vise to keep it from moving then hold outter joint straight and hit joint with hammer a few times and it will slide off, to install tap back on to lock it back on the shaft. with joint off remove old boot and clean shaft, insall new boot with clamp first then install outter clamp, install joint and grease, put grease into joint and the rest into the boot, make sure to clean the joint before installing it, after the install place the boot on the joint and clamp both clamps, install the axle, hope this helps, good luck.

Mar 20, 2011 | Buick Century Cars & Trucks

1 Answer

How do I replace the passenger side front axle?


remove passenger side wheel remove center nut on axle shaft i believe a 33 mm remove cotter pin on lower ball joint remove nut on lower ball joint with a ball joint seperating tool(pickle fork) seperate lower ball joint might need to tap axle shaft out of the wheel bearing pull the whole assembly aside where the axle goes into the transmission use a pry bar and pry out on the axle sometimes are stuck in pretty good then reverse the procedure to install be sure to torqe axle nut to specefications
good luck chris

Mar 09, 2011 | 2004 Pontiac Grand Am

2 Answers

How do i replace wheel side cv joint boot


YOU CAN GET A BOOT REPAIR KIT OR A ZIP BOOT.DO NOT LIKE ZIP BOOT,DOESNT WORK . BEST TO GET A REMANUFACTURED AXLE AND REPLACE AS A UNIT,DOESNT COST MUCH MORE AND WIL WORK WITH A WARRANTY.TAKE OFF WHEEL,LOOSEN AXLE NUT,TAKE OFF LOWER BALL JOINT,POP AXLE WITH HAMMER TO DRIVE AVLE OUT OF BEARING A LITTLE WAYS THEN PUILL UP ON STRUT ASSEMBLY TO GET AXLE ALL THE WAY OUT OF BEARING/HUB ASSEMBLT. POP OUT AXLE ANT HE SLIDE IN THE NEW UNIT

Dec 30, 2010 | 1994 Hyundai Excel

2 Answers

Front axle removal need help, have new axle to put on, tire off and axle nut off, what do i do now


separate the ball joint and the tie rod from wheel unit and swing it out far enough to slip axle out of wheel, pry it out of trans and replace

Nov 16, 2009 | 1989 Buick Electra

1 Answer

I need yo know how to replace the cv joint and


remove axle nut,seperate balljoint from control arm,usually a good whack with a hammer on the control arm near the balljoint will free it,pry control arm down to remove knuckle assy, remove roll pin from inner axle joint now you can remove axle,most of the time the inner joint boot tears this is called the d-o-j {double offset joint} replace this boot as well,my suggestion is consider replacing axle with reman depending on mileage 100k or more.remember when reinstalling axle splines need to be lined up on inner shaft so roll pin goes in without problem good luck

Jul 18, 2009 | 2001 Subaru Forester

1 Answer

Cv boot clamp came off somehow from the outer hub assembly


athere is a snap ring within the CV joint the nedds to be spread OPEN to release CV joint from axle, Once CV is cleaned and repacked with grease rintall onto axle by again spreading apart clamp. Prior to installing CV joint slide NEW CV joint boot onto axle, Cleanly intall add'l grrease and reinstall CV boot.

Apr 04, 2009 | 1996 Buick Century

1 Answer

Front axle u-joint


YOU will need to remove fornt hub/rotor assembly. this will reveal the spindle and 5 nuts holding it to the knuckle remove nuts slide off spindle and axle will then come out. then you can replace joint

Oct 17, 2008 | 1994 Ford F150 Styleside Supercab

Not finding what you are looking for?
2003 Toyota Land Cruiser Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...