Question about 2006 Dodge Caravan

1 Answer

Please if you could show me cv joint location with picture thank you.

Posted by on

1 Answer

Watch a You Tube Video

That is the best place to go, for all
the car questions

You can find anything you'll ever
want & in actual repair shops

Posted on Mar 23, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Put 2008dodge nitro onto ramps to see if I could locate the origin of a increaslily loud rattling coming from the front right passenger side appeRs to be cv joint. Where exactly is the cv joint located...


If it is the cv joint it would pop in turns the cv is the shaft from the transmission to the center of the wheel it has like 5 bolts on the trans side one big nut in the center of the wheel

Feb 24, 2015 | Cars & Trucks

1 Answer

Where is toyota constant velocity u-joint located


Like all front-drive cars using CV joints, there are 4 CV joints on the car near the engine. The vehicle has 2 axles (left and right, driving the corresponding front wheel). Each axle has 2 joints, one on each end. Typically the outer CV joints fail first, as their range of movement is greater due to steering the vehicle.

In modern practice the entire left or right axle is replaced when a CV joint goes bad.

Constant Velocity joints and U-joints perform a similar function, but are not really the same thing. U-joints are more typically used on rear-drive or truck-based 4WD vehicles.

Apr 27, 2014 | 2002 Toyota ECHO

2 Answers

Steering system knocks and makes noise at low speed turning. Is it a maintenance thing ?


Hi, check your drive axle CV joints. If the boots are torn, the joints are usually bad. A worn out CV joint will pop when you make a tight turn. If a CV joint is bad, I recommend replacing the whole axle, as the labor is much less than replacing just the joint. Please let me know if you have questions, and thanks for using FixYa.

Jan 09, 2011 | Pontiac G6 Cars & Trucks

1 Answer

Where can I find a cv joint replacement?


You can buy the replacement parts from any Napa, Carquest or major auto parts store chain, the CV joint is sold in a complete rebuilt assembly called a "Half Shaft". I show the cost to be about $50.00 each. Below is a picture of the assembly.

emissionwiz_5.jpg

Nov 05, 2010 | 1995 Honda Civic

1 Answer

My brother is looking for end caps for CV joints for his 1999 Alero


YOU CAN GO TO AUTO PARTS PLACE AND BUY THE CV JOINT BOOTS.YOU HAVE TO BUY THE BOOT CLAMPS CRIMP TOOL.IF YOU ARE GOING TO OVERHAUL YOUR CV JOINT ASSEMBLY.YOU NEED A REPAIR MANUAL TO SHOW YOU HOW TO TAKE CV JOINT APART.CLEAN IT UP AND REPACK.

Oct 13, 2009 | 1999 Oldsmobile Alero

1 Answer

How do I change the CV joints on a 1.8TD Ford Escort P reg


Hi mate

With the driveshaft removed from the vehicle.

Undo the the retaining straps on the CV boot.

Pull the CV boot up the driveshaft a little way, enough so you can clean all the old grease away.

Now look into the CV joint an locate the circlip that locks the CV to the driveshaft.

Now put the driveshaft into a vice with the CV joint facing downwards.

Now open the circlip and at the same time strike the CV joint. You can do this with a ballpin hammer if you are scrapping the CV joint. You can get a helper to stike the CV joint with a hammer while you keep the circlip open.

This will release the CV joint form the drive shaft.

Now clean the driveshaft of any old grease and fit a new CV boot if needed.

Now reverse the driveshift in the vice and fit the new CV joint. It will tap on with no trouble but do not damage it. Test it is on by trying to pull it off with your hands.

Now fill it with new grease.

Fit the CV boot to the CV joint and secure it to the CV joint.

Now it is ready to refit to your vehicle.

I trust this solves the problem for you.

Ray


Sep 08, 2009 | 1998 Ford Escort

3 Answers

CV JOINTS?


The CV joints are needed to transfer the torque at a constant speed to steered wheels as well as to accommodate up and down motions of the suspension.
You will find CV joints in all front-wheel drive cars. Many rear- and four-wheel drive cars and trucks have CV joints as well. The CV joint is packed with grease and protected by the rubber or plastic boot.
It does not require any maintenance and supposed to last very long provided that protective boot will not get damaged.

Aug 24, 2009 | 2006 Pontiac G6

2 Answers

Cb joint and transmission


yEAH! The CV axle transfers power to the wheels,, Just as a drive shaft does in a RRD

Mar 17, 2009 | 1994 Toyota Corolla

1 Answer

Replacing Outside Driver's CV Joint Boot


yes but youl have to give it a good whack with a "brass hammer" so you dont mar or damage the joint

Sep 07, 2008 | Hyundai Motor 1999 Elantra

Not finding what you are looking for?
2006 Dodge Caravan Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...