Question about 2001 Ford Crown Victoria

Open Question

2001 ford crown victoria 4.6L, backfires thru the air filter when accelerating in drive or in reverse, in park rams up fine, no obd codes, just change plugs and boots because I thought that was the problem, 60 pounds of fuel pressure, the only thing I put the gauge to check fuel pressure, there is no pressure until you turn the key on, turn the car off and pressure go's down right away, I thought its suppost to hold pressure for a minutes after its off? please help

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

97crownvic
  • 28 Answers

SOURCE: crown victoria window motor replacement

remove the door panel. be very careful and make sure you get all the screws out. Should be maybe 2 on the bottom half of the door, and 2 on the top half. one is right by the handle, which is the one i forgot the first time i took my door pannel off. carefully pull the panel upward, and outward at the same time. Once the panel is off, disconnect the controls, and remove the light from the panel. Remove the plastic cover very carefully, it will tear, just keeps noise, and air, and the elements out.
There will be 3 screws, they are torx bolts, once you pull those 3 out. They are located middle of the door towards the right side. The motor will drop down a little bit. disconnect the wires for the motor, and wiggle the motor off of the regulator. the crown vics have a decent size hole to get into the door panel, you can also remove the speaker if that would help you do it. other than that, it just lining up the new motor into the car, pushing it into the regulator, and putting the 3 bolts in, make sure they are snug, and not cross threaded. put everything back together, and your set.

Posted on Mar 19, 2009

CLEONTI
  • 33 Answers

SOURCE: need wiring diagram for 2008 ford crown victoria

Hello,

You can purchase the wiring diagram for $5.99 from the following site: http://www.wiring-diagram.com/. You can also purchase a wiring diagram book from the following link: http://cgi.ebay.com/ebaymotors/2008-FORD-CROWN-VICTORIA-MARQUIS-WIRING-DIAGRAM-MANUAL_W0QQitemZ120394723100QQcmdZViewItemQQimsxZ20090320?IMSfp=TL090320147007r15080.

Hope this helps,

Chris

Posted on Mar 23, 2009

  • 93 Answers

SOURCE: 2000 crown victoria serpentine belt installation

Accessory Drive Component Locationsa0011762.gif

Posted on Jun 09, 2009

  • 1 Answer

SOURCE: 1993 crown victoria

Try changing the mass air flow sensor located up by the air cleaner. Mine had a similar problem when you stepped on the gas it would pop (sounding like a backfire) and hardly had any power. I changed that sensor and it runs strong now.

Posted on Jun 15, 2009

  • 9 Answers

SOURCE: AC blows only thru the deforst

The switch for the changing from one to the other might be broke.

Posted on Jul 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

98crown victoria loss og power and stalling


Most Reported Problem Reports for the Ford Crown Victoria

repairpal.com > Problems > Ford
Verified for the Ford Crown Victoria. 4 reports. Engine Stalling and/or Hesitation on Acceleration due to Faulty Idle Air Bypass Valve. Verified for the Ford Crown ..

Aug 04, 2015 | Cars & Trucks

2 Answers

PLEASE HELP!!!! 93 ford crown victoria wont accelerate in gear after a while driving in hot weather


The problem is with your transmission It's getting hot and not engaging Check the tranny cooler as well

Apr 08, 2014 | Cars & Trucks

1 Answer

2001 ford crowin victoria not gettn fire


My car starts but when put in drive its very sluggish but when I put it in reverse it does not do it.

Oct 13, 2012 | 2001 Ford Crown Victoria

2 Answers

I have a 93 crown victoria and it runs great but more often when I put it into park it doesnt want to start again. I have to reput it in park 3 or 4 times.


Bad PRNDL switch(park/reverse/neutral/drive/low).May be adjustable,but most likely the switch is bad.As a temporary/free solution,try starting in Neutral(USE YOUR PARKING BRAKE!)

Mar 14, 2012 | 1993 Ford Crown Victoria

1 Answer

1993 crown victoria


Try changing the mass air flow sensor located up by the air cleaner. Mine had a similar problem when you stepped on the gas it would pop (sounding like a backfire) and hardly had any power. I changed that sensor and it runs strong now.

Mar 21, 2009 | 1993 Ford Crown Victoria

2 Answers

2000 Ford Crown Victoria


when you hold the accelerator does the vehicle stay running? if so the problem is in ithe IAC idle air control motor, take a small screw driver and using the handle tap the iac motor and usualy the motor will kick in and the vehicle will run fine then if the problem is rectified replace the IAC

Nov 24, 2008 | 2000 Ford Crown Victoria

Not finding what you are looking for?
2001 Ford Crown Victoria Logo

Related Topics:

143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...