Question about Dodge Dakota

Open Question

MI have a 2006 dodge durango with a 4.7L and there is a intermitent stalling problem when it's wet out side. Today I got a P2074 map/tp sensor etc...... and I have been replacing all of these sensors tp, iac, cam and now i'm kind of at a loss as to find the short in the vehicle wiring harness because i need wiring diagrams pls help!! Btw I work at a very small shop i have limited resourses but i have access to tools

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 208 Answers

SOURCE: 2000 ford explorer 4.0 x-engine is stalling, missing and lose power while driving

I personally would check the fuel pressure. Then I would go back to the coil. I have seen brand new bad coils out of the box. The symptoms of a loss of power point to this component, especially if the car idles well, but loses power when accelerating. Please do not rate this reply - we all are left to grasp at straws since you have changed pretty much everything. Good Luck. Please post the final fix of the problem.

Posted on Oct 28, 2008

  • 12 Answers

SOURCE: tp sensor replacement

it should be on your throttle body under the hood of your car

Posted on Apr 06, 2009

  • 116 Answers

SOURCE: Car stalls while driving

you have a bad crankshaft sensor. replace the crank sensor.

dodges and gm's are known for this problem.

Posted on Apr 10, 2009

jmgldsmth
  • 1869 Answers

SOURCE: 96 Dodge Intrepid ES, engine stalls

Find your firewall electrical junction block (where all the wires enter the cabin on the passenger side) and with a zip tie pull up the wire bundle so it does not ride on the upper tie rods and, fasten the zip tie to anything that is solid in the engine compartment and, let me know what happens

Posted on Jun 01, 2009

SOURCE: po748 can tcc solenoid or vehicle speed sensor cause this code

One question? Did you clear the codes out of the system with a scanner? I believe that's the only way to do it now,unlike the old days when you could rest by disconnecting the battery. Hope this helps.

Posted on May 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

04 dodge durango slt. Every time it rains my car stalls and check engine light comes on. Went through car wash also and it died. I can wash myself and don't have this problem. Maybe under engine??.


Something is getting wet. Check the codes with a code scanner to see if you can isolate the problamatic area. The code/s may point you to what circuit is causing your trouble

May 10, 2015 | 2004 Dodge Durango

3 Answers

Engine runs rough and stalls sets a p0068 code on a 05 dodge durango


P0068-MAMFQLD PRESSURE/THROTTLE POSITION CORRELATION
' Image
Theory of Operation
This DTC sets when an unexpected high intake manifold air flow condition exists that
can lead to increased engine speed and puts the NGC into a High Air flow Protection
limiting mode. The High Air flow Protection feature includes RPM limits for when a
Throttle and or MAP sensor limp-in fault is present.
When Monitored
During all drive modes.
Set Condition
If vacuum drops below 1.5Hg with engine RPM greater than 2000 RPM and closed
throttle. One Trip Fault. Three good trips to turn off the MIL.
Possible Causes
-VACUUM LEAK
-RESISTANCE IN THE (FS56) 5-VOLT SUPPLY CIRCUIT
-(FS56) 5-VOLT SUPPLY CIRCUIT SHORTED TO GROUND
-RESISTANCE IN THE (Kl) MAP SIGNAL CIRCUIT
-(Kl) MAP SIGNAL CIRCUIT SHORTED TO GROUND
-RESISTANCE IN THE (FS55) 5-VOLT SUPPLY CIRCUIT
-(FS55) 5-VOLT SUPPLY CIRCUIT SHORTED TO GROUND
-RESISTANCE IN THE (K22) TP SENSOR NO. 1 SIGNAL CIRCUIT
-(K22) TP SENSOR NO. 1 SIGNAL CIRCUIT SHORTED TO GROUND
-RESISTANCE IN THE (K900) SENSOR GROUND CIRCUIT
-MAP SENSOR
-THROTTLE POSITION SENSOR
-PCM
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding.
25312083-mkm0xbqveb5zta3uncrswycs-5-0.png Auto Repair Help US 25312083-mkm0xbqveb5zta3uncrswycs-5-2.jpg

Dec 07, 2014 | Dodge Cars & Trucks

1 Answer

I have a 2006 dodge Durango SLT 4.7 it is stalling sometimes when a take a corner and it jerks really hard just driving down the road. We had the code checked they cleaned my map sensor. This did not...


check if your ignition and fuel pressure are up to par. if you have a poor vacum signal from the sensor, check the engine vacum with a gauge. if its not around 19 or so you may have a sticking egr valve or other vacum leak. a plugged catalytic converter will cause low vacum also

May 20, 2014 | Cars & Trucks

1 Answer

What will cause acceleration loss and stalling?


This sounds like the common symtoms of a clogged fuel filter

Jan 11, 2014 | Dodge Durango Cars & Trucks

1 Answer

P0068 on a 2006 Dodge Ram 1500 SLT. Rough "hunting" for idle. Momentary lag/loss of power from a stop. Random RPM changes while at a constant speed. Sometimes it feels like it drops out of gear...


P0068 Symptoms - Engine Light ON (or Service Engine Soon Warning Light)
- Lack/Loss of power
- Engine rough idle Possible causes - Large vacuum leak
- Leaking air duct system
- Mass Air Flow (MAF) poor electrcial connection
- Manifold Absolute Pressure (MAP) poor electrcial connection
- Faulty Mass Air Flow (MAF) sensor
- Faulty Manifold Absolute Pressure (MAP) sensor
- TP sensor not seated properly.
- Faulty Throttle Position (TP) sensor.
- Dirty throttle body
When is the code detected? The Powertrain Control Module (PCM) monitors operation rationality check by comparing sensed throttle position to mass air flow readings
P0068 DODGE Description The Powertrain Control Module (PCM) monitors a vehicle operation rationality check by comparing Throttle Position (TP) to Mass Air Flow (MAF) readings. If, during a self-test, the comparison of the TP sensor and MAF sensor readings are not consistent with the calibrated load values, the test fails and a diagnostic trouble code is stored in continuous memory.

Jul 10, 2011 | Dodge Ram 1500 Cars & Trucks

1 Answer

Hello, I'm currently living on Guam and cannot find a mechanic who can correct my 2001 Dodge Durango (with error code P 0108) probelm. It will occassionally idle rough and stall. At times the "check...


P0108 = MAP sensor circuit high voltage

The MAP sensor communicates the barometric pressure inside the intake manifold to the ecm.
This code can indicate either a fault in the MAP (manifold absolute pressure) sensor, or a possible vacuum leak, either from a hose or the intake gasket.

It could be the connector on this sensor isn't making good contact. I would check the connector before you replace the sensor. It more than likely needs a new MAP sensor.

Jan 20, 2011 | 2001 Dodge Durango

1 Answer

I have a 2006 Dodge durango with a P2074 code what is that and how to i fix it


This code is in reference to a inaccurate amount of air to fuel mixture. Generally speaking a high air flow. This could be caused from a loose or broken vacuum line, or a faulty sensor.
I suggest that you do a thorough inspection of all the rubber vacuum lines under the hood. Any hose that shows signs of wear or damage should be replaced.
You should also look for any open vacuum ports that are sucking air. If you start the truck and listen very carefully you may be able to hear a sucking sound if you have a vacuum line broke.
You can also use a carb cleaner to spray around the vacuum lines and fittings with the engine running to see if you get a idle change. If you do get a idle change or stall then you are in the area of the problem. You will then need to look at each hose real good.
If after testing you do not find any leaks or missing hoses, then you may have to replace the MAP (Manifold Absolute Pressure Sensor).

Aug 09, 2010 | 2006 Dodge Durango

2 Answers

Wife's durango is idling rough and running rough


With both codes pointing at TP sensor, I'd certainly take the time to replace it, as well as make sure connections to it are clean, and good. Chances are, you won't be able to take part back anyway. As far as exhaust goes, if it's leaking in the right places in may cause improper readings at sensors downstream, but if not obvious leak, I wouldn't be concentrating in that area right now.

Nov 01, 2009 | 2004 Dodge Durango

1 Answer

Diagnostic Code P2074 on 2007 PT cruiser-can't find on OBD list.


P2074-manifold Pressure/throttle Position Correlation

CORRELATION - HIGH FLOW/VACUUM LEAK

When Monitored: Engine Running, during all drive modes.
Set Condition: If vacuum drops below 1.5 Hg with engine RPM greater than 2000 RPM
at closed throttle.

POSSIBLE CAUSES

VACUUM LEAK
HIGH RESISTANCE IN MAP (K7) 5 VOLT SUPPLY CIRCUIT
RESISTANCE TO GROUND IN MAP (K7) 5 VOLT SUPPLY CIRCUIT
MAP SENSOR
HIGH RESISTANCE IN (K1) MAP SIGNAL CIRCUIT
RESISTANCE TO GROUND IN (K1) MAP SIGNAL CIRCUIT
HIGH RESISTANCE IN (K4) MAP GROUND CIRCUIT
PCM
TP SENSOR OPERATION
HIGH RESISTANCE IN (K6) TP SENSOR 5 VOLT SUPPLY CIRCUIT
RESISTANCE TO GROUND IN (K6) TP SENSOR 5 VOLT SUPPLY CIRCUIT
TP SENSOR
HIGH RESISTANCE IN (K22) TP SIGNAL CIRCUIT
RESISTANCE TO GROUND IN (K22) TP SENSOR SIGNAL CIRCUIT
HIGH RESISTANCE IN TP (K4) SENSOR GROUND CIRCUIT

Mar 27, 2009 | 2007 Chrysler PT Cruiser Touring Hatchback

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...