Question about Suzuki Vitara

Open Question

Clutch on my suzuki wagon is very fierce and biting at the top of the pedal. can you adjust it to soften it.? i have selected vitara , as wagon r not on menu

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 35 Answers

SOURCE: MAZDA MX5 CLUTCH PROBLEM

you have to bleed the clutch cause it should be an hydraulic one... if you still have a lot of free play after that it means the clutch is worn too much....

Posted on Apr 27, 2009

  • 51 Answers

SOURCE: audi tt clutch pedal adjustment.Bite point too

i think that model is hydrolic if so try bleeding the clutch if that does not work the clutch will need to be replaced

Posted on Aug 27, 2009

  • 534 Answers

SOURCE: have to change clutch plate on suzuki grand vitara

If it's hard to get into gear you should check the clutch is disengaging properly.
Before changing the clutch plate, check that the clutch throw-out is adjusted correctly and the actuating hydraulics/levers have the correct amount of travel.

Posted on Oct 11, 2009

roniecon
  • 6826 Answers

SOURCE: can the clutch be udjusted

This is a hydraulic fluid clutch system.No adjustments can be made.If the clutch can not disengaged enough for gears to shift smoothly,then the master,or the slave are bad.The master is where the clutch pedal goes to.The slave is down on,or in the transmission.If the slave is bad,they will leak,but not always.Most of the time the slave is the cause of this.But look at the slave real good,it most likely is leaking a little bit.Bleeding the system might give your clutch new life,for a while,until the air gets back in the system.

Posted on Oct 17, 2009

  • 2 Answers

SOURCE: problems with clutch master cylinder on a suzuki

I too am having problems with my 2006 GV clutch master cylinder. I noticed gradually over several weeks the gears and clutch pedal were degenerating and then the cluth gave completely. My mechanic took a look around and said the cylinder is the cheapest one he has ever seen, it's just a piece of plastic apparently! Is going to hopefully get the part this week or next, though he said as it's such a cheap and nasty part its likely it will happen again in the future. Not happy!

Posted on Mar 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can you adjust a clutch on suzuki vitara 2.7


I think you will find the actuating system is hydraulic, hence not adjustable. There may however be some small adjustment on the rod which connects the clutch pedal to the clutch master cylinder to take the slop out of it. You would feel that kind of slop when you push the pedal down. Clutch is good for about 10 years of normal driving, so you are at 12 and it is time for a new clutch.

Mar 08, 2011 | 1999 Suzuki Vitara

2 Answers

My clutch is barely engaging even when depressed all the way to the floor. Can it be adjusted or dose it need a clutch replacement?


I would try adjusting the clutch master such that the point of engagement at the pedal, is further from the floor. This will effectively increase the travel of the clutch slave and possibly solve your problem. The clutch master pushrod should have an adjustment behind the pivot at the pedal bracket. Usually a lock nut has to be loosened off a little and then the rod screwed out of it's holder to effectively lengthen it.

Jan 24, 2011 | 1999 Suzuki Grand Vitara

1 Answer

The clutch pedal on Suzuki vitara two litre V6 1998 goes to about inch of floor before activation. Clutch does not slip just too much pedal travel. Is it possible to adjust it? ...


prev.gif next.gif Clutch ADJUSTMENTS 1997-98 Models CLUTCH PEDAL HEIGHT The clutch pedal height should not be a periodic adjustment but may be checked after components of the mechanical clutch system have been replaced. The proper clutch pedal height should be 0.2 in. (5mm) above the brake pedal height If adjustment is necessary, loosen the locknut and turn the adjusting bolt until the appropriate height is reached. Once set, keep the bolt from turning and tighten the locknut to secure the adjustment. CLUTCH PEDAL FREE-PLAY The clutch pedal free-play should be checked from time-to-time in order to assure proper clutch operation. The proper clutch free-play should be 0.6-1.1 in. (15-25mm). Fig. 1: Pedal free-play is adjusted at the joint nut (2), while keeping the outer cable nuts (3) tightened around the center cable thread portion 7924hg30.gif
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. If the free-play must be adjusted, turn the joint nut (2) located at the transmission end of the clutch cable in or out, as necessary to achieve the proper play.
  3. Once the correct pedal free-play is obtained, check the free-play on the release arm (c), it should be 0.02-0.06 in. (0.5-1.5mm).
1999-01 Models These vehicles are equipped with a hydraulic clutch system. No adjustment is necessary.

Nov 05, 2010 | 1999 Suzuki Vitara

2 Answers

Clutch bites high up on pedal movement


check clutch master cylinder rod adjustment and pedal height should be just higher than brake pedal. could try and bleed system also.
most hydraulic clutch systems have high take up points, adjust master cylinder rod, check for free play at top after adjusting if all that is O.K. then clutch plate may be nearly worn out but not slipping at this stage.

Jul 29, 2009 | 1997 Ford Escort

1 Answer

Clutch will not engage, can shift gears with motor off only


cut, bronzed, and reinstalled..for now works very well...it was a wagon r 2006...thanks for trying.

Jun 20, 2009 | 1999 Suzuki Grand Vitara

1 Answer

Susuki vitara clutch adjustment


Location of the adjusting bolt is just above the pivot of the pedal. Loosen the locking nut then make the necessary adjustment. Dont forget to tighten the lock nut once through.

May 16, 2009 | 1999 Suzuki Vitara

1 Answer

Self ADjusting Clutch Cable


Your car uses a hydraulic clutch, they are self adjusting and there is no way to adjust them provided, when the pedal engages near the top of its travel this means the clutch disk is worn out.

May 01, 2009 | 1998 Volkswagen Jetta

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...