Question about 2003 Ford Windstar

1 Answer

Waterpump - 2003 Ford Windstar

Posted by on

  • Iron
    Iron Mar 22, 2011

    I need more information about your problem before I can offer a solution. Thank you.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Expert
  • 1,114 Answers

Are you looking to replace it? If so this is a job.

Posted on Mar 22, 2011

  • Charles Huckeba
    Charles Huckeba Mar 22, 2011

    If you don't have a Haynes, or Chilton's manual, then I would recommend that you get one. This is q cumbersom job, time consuming, and will require quite a bit of time.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rodeo waterpump blew now wont start


Hi, The first thing I would check is the BATTERY. Check the connections and wire conditions. The waterpump has no connection to the battery. The motor drives the pump. Hope that helps.

Aug 13, 2014 | Cars & Trucks

1 Answer

Waterpump


pull out your coolant res.
pull off your belt.
you will see the old waterpump.
remove all four bolts.
clean off gasket off waterpump mount on motor.
place gasket.
install.

Jun 30, 2012 | 1999 Pontiac Sunfire

1 Answer

How do i tell if my overheating problem is the waterpump on my 2.0 l '96 contour?


remove coolant thermostat and run vehicle if overheating occurs waterpump is problem

Apr 12, 2012 | 1996 Ford Contour

1 Answer

Where is the water pump located at on a 1996 olds88LS i put water in the radiator and standing on the passanger side i can see it coming down in a study stream from under neath the car but not from the...


Hello: The waterpump is on the passenger side of engine. Either the heater hoses are leaking or the waterpmp shaft seals or the radiator hose that attaches to the waterpump. The waterpump is located about in the center, its pulley does not have groves and the pulley is held on the waterpump with 4 10mm bolts.

Nov 06, 2010 | 1996 Oldsmobile 88

1 Answer

Procedure on changing waterpump


  1. first drain the cooling system.
  2. loosen bolts on the waterpump pulley and remove the inner fender cover on the pass/side.
  3. remove the surpentine fan belt, note; make a diagram of the belt routing so belt will go back on the right way.
  4. remove the bolts you loosened on the pump pulley, use a pry bar to pry engine back to have enough room to remove the waterpump pulley.
  5. remove the bolts holding waterpump, you will want a pan under the van to catch coolant when waterpump is removed,
  6. remove the pump and clean old gasket off the block and install new pump,
  7. reverse to install new pump and fill system with coolant allow engine to run until thremostat opens,hope this is helpful. heres a few diagrams of the waterpump and the cover and the belt routing, good luck and hope this is helpful.
  8. e0c2b8f.png3e5449e.giff12ccdc.gif

Oct 27, 2010 | 2005 Dodge Caravan

2 Answers

Do you have to remove power steering belt pulley to change the water pump?


no, just remove the belt, then the cover over the waterpump then the waterpump pulley,NOTE; loosen waterpump pulley bolts before removing the belt,just loosen dont remove!,next is to remove bolts holding waterpump and pump comes out,9e51b2d.gif

Apr 10, 2010 | 2004 Chevrolet Impala

2 Answers

Leaking coolant checked radiator hoses and


take a look at the waterpump, these cars have problems with waterpump leaking, take caution, the waterpump is driven by the timing belt,if that belt pops or jumps due to coolant leaking on it and causing it to fail,then you will have a costly repair,i belive its about $4,000 to fix, it will cause cylinder head valves to bent, have this coolant leak check asap.

Mar 02, 2010 | 2000 Volvo V70

2 Answers

Water leakking from 5mm hole on side of water pump ford transit 1997


This is called a weep hole and it indicates the rubber seal is now leaking antifreeze onto the waterpump bearing and it's only a matter of time before the waterpump falls change the waterpump.

Dec 31, 2009 | 1987 Ford EXP

2 Answers

Waterpump removing fan


Well, if it's a 5.0L engine, remove the 4 bolts holding the fan to the pulley. If it's a 4.0L engine, you need to hold the waterpump pulley still and break the nut loose holding the fan clutch to the waterpump. If you don't have a wrench that big, try using a long chisel on the edge of the nut and hitting it very hard with a hammer to break it loose.

Feb 15, 2009 | 1996 Ford Explorer

Not finding what you are looking for?
2003 Ford Windstar Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...