Question about 2004 Scion xB

1 Answer

My 2004 xb seems to be ill. twice after sitting 8 hours in the parking lot on a rainy nite, I was going down a steep ramp to enter onto the freeway and my car all but died then spit and sputtered then started doing semi better well good enough to make it home then died 3 times while trying to get into the driveway, the next day she ran fine going back to work but the check engine lite came on again just like the time it happened last month, I changed spark plugs and had my fuel injectors cleaned. HELP

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 22 Answers

Check-out battery,could be weak or on its last LEG....

Posted on Apr 25, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I ask a question on what is the drive cycle to reset obd for toyota2005 rav4


Step One: How to Prepare Your Vehicle
  • Have the fuel tank between 30 and 70 percent full. Some systems, especially the EVAP system, need to have a specific level of fuel in order for the tests to be trusted. If the fuel tank is near empty or completely full, many of the basic tests will not run at all.
  • The vehicle must also have a good alternator and a strong battery. If you have to occasionally jump-start your vehicle, all of the memory from the powertrain control module (PCM) is erased, which includes the data that accurately tracks the results from various stages of the Drive Cycle. Also, if the battery is weak or undercharged, some of the most important tests will never run.
  • The vehicle must sit overnight, or for at least eight hours, in an environment that is less than 90° F. The engine temperature needs to match the air temperature in order to establish an accurate baseline for the testing. If the outside temperature is over 90° F, the fuel is too volatile and the EVAP system won't even try to run its tests, though some of the other emissions systems may run their tests.
  • The keys must be out of the ignition and all of the doors must be closed while the vehicle sits over night because many of the onboard computers "boot up" when the keys are in the ignition. Also, many of the onboard computers still run until all of the doors are closed after the vehicle is shut off and the keys are removed.
Step Two: The Cold Start
  • Start the vehicle and let it idle for two to three minutes in Park or Neutral. While it is idling, turn on the head lights, heater/defroster, and rear defroster for a three to five minute warm-up phase. Let the idle speed settle down to near the normal speed.
  • Next, put the vehicle in gear and drive through city streets at about 25 mph. Go up to about 35 to 40 mph a few times before slowing down to stop. Don't roll through the stop; be sure the car is really stopped, just like you learned in driving school. Accelerate from each stop in a normal fashion-not overly conservative, but not like you are competing in a drag race either.
Step Three: A Short Freeway Trip
  • After the vehicle has been cold started and driven for a few miles on city streets, the next step is to take it on a short freeway trip.
  • Enter the freeway on-ramp and allow enough room with respect to other vehicles so that you can do a 1/2 to 3/4 throttle acceleration up to freeway speed.
  • When you have accelerated up to around 60 mph and have safely merged into the flow of traffic, stay in the slow lane and maintain a steady speed of 55 to 60 mph for a minimum of five miles. Please use the cruise control to help you maintain speed.
  • Find a nice, long off ramp to exit from the freeway. As you exit, take your foot off of the accelerator and let the vehicle coast down until it stops under its own power as you complete your exit from the freeway. Do not use the foot brake and do not shift gears until the very end of this "coast down" phase.
  • Step Four: More City Driving
    • After you have completed the freeway trip, drive through the city streets for a repeat of the second part of Step Two.
    • Go up to about 35 to 40 mph a few times and then maintain a city speed of 25 mph before slowing down to stop. Again, don't roll through the stop and make sure to accelerate normally.
    • Pull in to a parking place and let the engine idle for one to two minutes and then shut it off.
    Step Five: Have your Readiness Monitors Checked and Verified
    • Drive your vehicle to your regular shop and have them re-check your readiness monitors, present codes, and pending codes. They should do this as a courtesy and for free.
    • If all of your monitors are "ready" and there are no present or pending codes, then your vehicle has been properly repaired and is ready for an emissions inspection and for normal driving.

Feb 21, 2017 | Cars & Trucks

1 Answer

How to do the drive cycle of a 1996 Nissan pathfinder


How to Perform a Basic Drive Cycle


Step One: How to Prepare Your Vehicle

  • Have the fuel tank between 30 and 70 percent full. Some systems, especially the EVAP system, need to have a specific level of fuel in order for the tests to be trusted. If the fuel tank is near empty or completely full, many of the basic tests will not run at all.
  • The vehicle must also have a good alternator and a strong battery. If you have to occasionally jump-start your vehicle, all of the memory from the powertrain control module (PCM) is erased, which includes the data that accurately tracks the results from various stages of the Drive Cycle. Also, if the battery is weak or undercharged, some of the most important tests will never run.
  • The vehicle must sit overnight, or for at least eight hours, in an environment that is less than 90° F. The engine temperature needs to match the air temperature in order to establish an accurate baseline for the testing. If the outside temperature is over 90° F, the fuel is too volatile and the EVAP system won't even try to run its tests, though some of the other emissions systems may run their tests.
  • The keys must be out of the ignition and all of the doors must be closed while the vehicle sits over night because many of the onboard computers "boot up" when the keys are in the ignition. Also, many of the onboard computers still run until all of the doors are closed after the vehicle is shut off and the keys are removed.
Step Two: The Cold Start
  • Start the vehicle and let it idle for two to three minutes in Park or Neutral. While it is idling, turn on the head lights, heater/defroster, and rear defroster for a three to five minute warm-up phase. Let the idle speed settle down to near the normal speed.
  • Next, put the vehicle in gear and drive through city streets at about 25 mph. Go up to about 35 to 40 mph a few times before slowing down to stop. Don't roll through the stop; be sure the car is really stopped, just like you learned in driving school. Accelerate from each stop in a normal fashion-not overly conservative, but not like you are competing in a drag race either.
Step Three: A Short Freeway Trip
  • After the vehicle has been cold started and driven for a few miles on city streets, the next step is to take it on a short freeway trip.
  • Enter the freeway on-ramp and allow enough room with respect to other vehicles so that you can do a 1/2 to 3/4 throttle acceleration up to freeway speed.
  • When you have accelerated up to around 60 mph and have safely merged into the flow of traffic, stay in the slow lane and maintain a steady speed of 55 to 60 mph for a minimum of five miles. Please use the cruise control to help you maintain speed.
  • Find a nice, long off ramp to exit from the freeway. As you exit, take your foot off of the accelerator and let the vehicle coast down until it stops under its own power as you complete your exit from the freeway. Do not use the foot brake and do not shift gears until the very end of this "coast down" phase.
Step Four: More City Driving
  • After you have completed the freeway trip, drive through the city streets for a repeat of the second part of Step Two.
  • Go up to about 35 to 40 mph a few times and then maintain a city speed of 25 mph before slowing down to stop. Again, don't roll through the stop and make sure to accelerate normally.
  • Pull in to a parking place and let the engine idle for one to two minutes and then shut it off.
Step Five: Wave your Readiness Monitors Checked and Verified
  • Drive your vehicle to your regular shop and have them re-check your readiness monitors, present codes, and pending codes. They should do this as a courtesy and for free.
  • If all of your monitors are "ready" and there are no present or pending codes, then your vehicle has been properly repaired and is ready for an emissions inspection and for normal driving.
  • If your monitors are not ready, please click here for more information.

May 26, 2016 | Nissan Cars & Trucks

1 Answer

How to do the drive cycle on a 1996 nissan pathfinder


How to Perform a Basic Drive Cycle


Step One: How to Prepare Your Vehicle

  • Have the fuel tank between 30 and 70 percent full. Some systems, especially the EVAP system, need to have a specific level of fuel in order for the tests to be trusted. If the fuel tank is near empty or completely full, many of the basic tests will not run at all.
  • The vehicle must also have a good alternator and a strong battery. If you have to occasionally jump-start your vehicle, all of the memory from the powertrain control module (PCM) is erased, which includes the data that accurately tracks the results from various stages of the Drive Cycle. Also, if the battery is weak or undercharged, some of the most important tests will never run.
  • The vehicle must sit overnight, or for at least eight hours, in an environment that is less than 90° F. The engine temperature needs to match the air temperature in order to establish an accurate baseline for the testing. If the outside temperature is over 90° F, the fuel is too volatile and the EVAP system won't even try to run its tests, though some of the other emissions systems may run their tests.
  • The keys must be out of the ignition and all of the doors must be closed while the vehicle sits over night because many of the onboard computers "boot up" when the keys are in the ignition. Also, many of the onboard computers still run until all of the doors are closed after the vehicle is shut off and the keys are removed.
Step Two: The Cold Start
  • Start the vehicle and let it idle for two to three minutes in Park or Neutral. While it is idling, turn on the head lights, heater/defroster, and rear defroster for a three to five minute warm-up phase. Let the idle speed settle down to near the normal speed.
  • Next, put the vehicle in gear and drive through city streets at about 25 mph. Go up to about 35 to 40 mph a few times before slowing down to stop. Don't roll through the stop; be sure the car is really stopped, just like you learned in driving school. Accelerate from each stop in a normal fashion-not overly conservative, but not like you are competing in a drag race either.
Step Three: A Short Freeway Trip
  • After the vehicle has been cold started and driven for a few miles on city streets, the next step is to take it on a short freeway trip.
  • Enter the freeway on-ramp and allow enough room with respect to other vehicles so that you can do a 1/2 to 3/4 throttle acceleration up to freeway speed.
  • When you have accelerated up to around 60 mph and have safely merged into the flow of traffic, stay in the slow lane and maintain a steady speed of 55 to 60 mph for a minimum of five miles. Please use the cruise control to help you maintain speed.
  • Find a nice, long off ramp to exit from the freeway. As you exit, take your foot off of the accelerator and let the vehicle coast down until it stops under its own power as you complete your exit from the freeway. Do not use the foot brake and do not shift gears until the very end of this "coast down" phase.
Step Four: More City Driving
  • After you have completed the freeway trip, drive through the city streets for a repeat of the second part of Step Two.
  • Go up to about 35 to 40 mph a few times and then maintain a city speed of 25 mph before slowing down to stop. Again, don't roll through the stop and make sure to accelerate normally.
  • Pull in to a parking place and let the engine idle for one to two minutes and then shut it off.
Step Five: Wave your Readiness Monitors Checked and Verified
  • Drive your vehicle to your regular shop and have them re-check your readiness monitors, present codes, and pending codes. They should do this as a courtesy and for free.
  • If all of your monitors are "ready" and there are no present or pending codes, then your vehicle has been properly repaired and is ready for an emissions inspection and for normal driving.
  • If your monitors are not ready, please click here for more information.

May 26, 2016 | Nissan Cars & Trucks

2 Answers

Remote starter only allows my starter to turn over twice; needs at least 3 with my key. How to adjust to have it starter run longer on remote?


I know you are looking to have the remote starter run a third time but I would say you need to look at your Fuel Pressure Regulator on the Scion. Sounds like it is not holding fuel pressure at the fuel rail and that is why it requires a third Crank

Jan 05, 2016 | 2006 Scion xB

1 Answer

1994 Toyota Corolla can't get past 35 mph on highway with steep uphill grade


Way back when, I had a '73 Corolla.

It was for mostly around town, which it did ok.

One time went on the freeway, and couldn't get it to go over 45 MPH.

It turned out to be the fuel filter needed replacing.

Open the hood and disconnect the negative battery cable.
Locate the fuel filter. It is in a bracket that is located on the firewall (near the brake master cylinder).
Clear away anything blocking access to the top of the filter.
Remove the threaded banjo bolt at the top of the filter, using a backup wrench to keep the filter from twisting.
Loosen the flared fitting at the bottom of the filter using a flare-nut wrench, if possible.
Remove the bracket bolts, the used filter and the filter support bracket.
Install the new fuel filter in the support bracket on the firewall using the bracket bolts.
Attach the inlet and outlet pipes to the filter, using the new crush washers that are supplied with the filter, and tighten them.
Replace anything that was moved for access to the filter and reconnect the negative battery terminal.
Start the car and check the filter for leaks.

Feb 12, 2014 | Toyota Cars & Trucks

1 Answer

My 1999 buick regal leaks coolant, not while its running, only hours later after it cools down. its not leaking from the radiator, or the reservoir, is there another solution besides replacing the wat


Water Pump Worn out or hose leaks

Never use any leak seal products on any
part of the car ,your asking for trouble & there
in there for life

Always make the proper repair

Mar 13, 2013 | Cars & Trucks

1 Answer

After i filled my 2004 hyundai xg350 last nite and parked for half hour then drove hime ,it stalled ,but rstrated right away,but kind of jerked a little bit, when applying gas. after that i drove home...


Hello,
Absolutely, a dirty fuel filter could cause that. You may also check your air filter, a dirty air filter can cause a bad fuel/air mix ratio, which can have similar results to a dirty fuel filter.

I hope this helps you.

Feb 02, 2011 | 2004 Hyundai XG350

1 Answer

Door lights turn on at random, I have tried slamming doors BUT it only works when it wants. Lights turn on at random on the freeway and sometimes just sitting in the nite while parked in front of our home,...


Try spraying wd40 or any type of rust penetrant inside the door latches. The switches stick from dirt and will eventually free up. Spray the latch then open and close each door sevearl times. May take a couple tries. Good luck.

Oct 03, 2009 | 2000 Ford Expedition

Not finding what you are looking for?
2004 Scion xB Logo

Related Topics:

265 people viewed this question

Ask a Question

Usually answered in minutes!

Top Scion Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Brad Brown

Level 3 Expert

15557 Answers

Are you a Scion Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...