Question about Nissan Maxima

1 Answer

NOT GETTING FIRE I CHANGED THE CAM AND BOTH CRANK SENSORS CHECKED THE FUSES AND RELAYS WHATS NEXT

Posted by on

  • Anonymous Mar 22, 2014

    changed crank sensor and checked fuses

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 878 Answers

You know that when you change the cams you have to put them marking with the timing chain silver links

Posted on Mar 22, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 2001 dodge durango will crank and start for about a second changed cam sensor ,crank sensor,pcm,fuel regulator and still wont run its getting fire and compression and fuel but still wont run any...


Check starter relays & fuses check all fuses for electrical modules
drivers side inner finder electrical pannel for starter check all fuses and relays

Aug 15, 2013 | 1997 Dodge Intrepid

2 Answers

97 buick park avenue change cam and crank sensor still no fire


asd relay or fuse
camshaft not spinning
bad pcm
damaged wiring harness

Mar 25, 2013 | 1997 Buick Park Avenue

1 Answer

I have a 2004 KIA optima I changed timing belt now there's no fire going to coils I changed crank and cam sensor.


Go to the engine compartment fuse relay box and check the fuse ECU fuse right next to it is the main fuse make sure those 2 fuses are not open,for some reason you dont have power

Mar 23, 2012 | 2004 Kia Optima

3 Answers

Engine cranks over but no fuel being pumped plus no power to fuel pump. No spark to the spark plug. I put new crank positioning sensor, new cam sensor, changed computer, checked fuel pump relays. Car...


Did you check your coil pac? This supplys power to all parts of your auto. I would check and see if your getting fire comming from your coil , Good luck to you.

Mar 31, 2011 | 2001 Nissan Sentra

2 Answers

My 02 chevy cavalier turns over but will not start. I have replaced ever thing i know that could be wrong.


does it produce fire does the gas pressure rise does the crank sensor and cam sensor work

Feb 09, 2011 | Chevrolet Cavalier Cars & Trucks

1 Answer

Im not getting fire on my 2001 jeep cherokee. coil rail is good and the cam position sensor is new and still no fire. im getting fuel but i think there is no fire. any idea as to what im overlooking? jeep...


If no spark at the plugs, engine cranking, did you check primary voltage at the coil assemble, dark green wire with orange tracer, engine cranking, use a test lite on the wire check for voltage. If no voltage that will lead back to asd relay. There are some fuses involved. I believe the computer has to see both the cam and crank sensor signals or it won't ground the asd relay. All I can do is make testing suggesting.
cherokee asd relay-m5cnn2lotweryjtsi2x53sss-2-0.jpg

Mar 10, 2017 | 2001 Jeep Cherokee

1 Answer

Fuel pump not getting fire ,changed fuel pump and the relay.An pump still not coming on


why did you change the pump?
did you check the Auto shut down relay?
Do you have a signal from the cam and crank sensor?
Did you check the fuel pump fuse?
too many things need check before I can help.

Dec 16, 2009 | 1998 Buick Century

3 Answers

No spark installed new coil and had mogel for the distibutor checked


Check fuses relays and ground wires. The check inside the distributor cap and make sure the piece the rotor inside distributor is clean of oil and the area below hall effect is dry and without oil.The piece down below is also a item that can effect it from firing.it is a magneto and it controls the firing and fuel by sending signals to the ecm. If you check the above without finding an issue the best thing to do is see if you can borrow a scan tool to get any codes that could be helpful with diagnosing. Im sorry if this isnt exact help but it is trail and elimination that fixes issues like this instead of just replaceing parts.

Oct 03, 2009 | 1995 Ford Taurus

1 Answer

1996 Chrysler LHS not firing


First, check the ECM fuse in the power control module (it will be a yellow 20 amp fuse). Second, check the timing belt. You can pull out the cam sensor and look in the hole while someone cranks the motor. If the cam gear is not turning, the timing belt is broken. VERY IMPORTANT - when replacing the cam sensor, get a special adhesive pad from a Chrysler dealer that attaches to the bottom of the sensor to set the proper gap (cost about $2). Install the cam sensor until the pad touches the gear and tighten down the locking bolt. The pad will wear off in normal running. If the gap is not set correctly using this gapping pad, you won't start.

May 12, 2009 | 1996 Chrysler LHS

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...