Question about 2000 Hyundai Sonata

1 Answer

I change the crank position sensor and now get the code 443 and 161 and i can't erased and a won't start

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 22,326 Answers

P0433....Heated Catalyst Efficiency Below Threshold (Bank 2)


P0161....O2 Sensor Heater Circuit (Bank 2 Sensor 2)

you have a problem with the O2 sensor but as for it not starting then iam not sure as i cannot see this from stopping the engine from starting ,check the crank sensor with a automotive multimeter to see if its producing a voltage

Posted on Mar 22, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOw many crank positions sensors on a 2000 GMC 2500 savana. I replaced one and the same code keep showing up. Crank but won’t start.


There is crank and cam sensors.If you changed the crank sensor at the front under the front crank pulley and it is in the correct installed position, you should not have a code for that,unless the wiring is defective or the crank sensor is defective.

Mar 01, 2018 | GMC Cars & Trucks

1 Answer

L have a 2003 Kia Sorento, sometimes it will just turn over but won,t crank. after a while it will start up. or l can be driving down the road and it will start poping and cut off, and won,t start.it does...


It will be a position sensor problem Check the air gap and check that the censor rotor is tight and that there is no material getting in the air gap causing a problem

Jan 06, 2014 | Kia Cars & Trucks

1 Answer

1998 vw beetle 2.0 standard code p0322 chk engine speed sensor it chks good changed plugs and it stalled again


Resecure loose wire or connectors - If battery charge is low, recharge or replaced battery - Replaced crank position sensor - Replaced starter motor

I’m happy to assist further over the phone at https://www.6ya.com/expert/brock_d67526d2a834c47e

Dec 16, 2013 | 1998 Volkswagen Beetle

1 Answer

Fault code p0340


crankshaft or camshaft position sensor an/or wiring problem, is it petrol or diesel? if its petrol check wiring at front of engine near crank pulley before changing sensor

Nov 09, 2013 | 2006 Jaguar X-Type

2 Answers

98 blazer 4.3 engine won't start code p0336, already replaced crank sensor


which crank sensor do you replaced ? the P0336 means P0336 Crankshaft Position Sensor A Circuit Range/Performance.

________________
autel maxidas 708

Feb 25, 2013 | 1998 Chevrolet Blazer

1 Answer

My 94 fors Taurus cuts out while driving and sometimes will not start. It cranks but won't start. We changed the fuel pump, spark plugs and distributor cap, but it is still cutting out while driving...


are there any codes? have you checked the pressure in the fuel line. you may have a bad fuel pressure regulator. or a bad crank position sensor. spray starter in the throttle body and see if it starts

Dec 14, 2012 | Cars & Trucks

1 Answer

My 1996 Taurus sho cranks but won'tstart up change


Try replacing the camshaft position sensor usually solves the problem.

Jul 03, 2012 | Cars & Trucks

1 Answer

Code reads P0340 Camshaft position Sensor circuit


That makes the computor think the timing is off. Replace the sensor and see if that does it. You will then have to have the code cleared (erased) or the light will come back on/stay on.

Mar 19, 2010 | 1996 Dodge Caravan

1 Answer

Where is the ignition module on a 2003 Kia Sedona 3.5? I have a no start condition. No spark. Crank sensor?


you got to scan for codes first ,crank the engine first ,don"t put key in off position (that may erase CPS sensor codes )and scan it first.

Feb 03, 2010 | 2003 Kia Sedona

Not finding what you are looking for?
2000 Hyundai Sonata Logo

Related Topics:

169 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

80668 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...