Question about Dodge Intrepid

1 Answer

Wipers do not work when switch turned on. low or high. Fues look good. I think washer pump is also not working do the two of them have anything in common?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 127 Answers

Must replace wiper moter. Washer pump and wiper moter is all one unit

Posted on Mar 22, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wipers will not turn on 2006 colorado


There are two relay's in the under hood fuse / relay box . Wiper relay an wiper relay 2 . Maybe one is bad . also check fuse #14 25 amp. Wiper fuse.Plus the BCM - body control module has a hand in making the wipers work . Are you familiar with automotive electronic control modules ?
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper micro relay
• Wiper 2 relay
• Wiper diode
• Windshield wiper motor
• Windshield washer pump
• Windshield washer nozzles
• Windshield washer solvent container
• Windshield wiper arm and blade assemblies
• Windshield wiper transmission
• WIP/WASH 10A fuse
• WIPER 25A fuse

Wiper/Washer System Description
The body control module (BCM) controls wiper motor low speed operation. The washer pump and high speed operation are controlled directly by the wiper/washer switch. The windshield wiper/washer switch supplies voltage on the signal circuits to the BCM for windshield wiper/washer operation. When WASH, MIST, DELAY, LOW, or HIGH is detected, the BCM energizes the wiper micro relay by suppling voltage to the relay coil. This allows battery voltage from the WIPER fuse to flow through the relay switched input then through the contacts and out the relay switched output to the wiper 2 relay switch contacts. Since the wiper 2 relay switch contacts are normally closed to the low speed circuit of the windshield wiper motor, the motor will operate at low speed.

Do you have any speed !

Oct 06, 2017 | Cars & Trucks

1 Answer

In my 2007 Saturn Vue there is what I think is an air pump which is cracked that one port is not connected to anything.


There is a electric motor that pumps washer fluid . Located in the bottom of the washer fluid tank .
Wash Operation (Front and Rear Wipers)
The front and rear washer systems use the same windshield washer fluid pump. When either the front or rear wiper is in the washer position voltage will be supplied to one side of the windshield washer fluid pump (depending on whether it is front or rear), while the other side of the pump is grounded.
At this point, the windshield washer fluid pump sprays solvent onto the windshield. When the front or rear washer is activated, the BCM receives an input from the switch that is activated. The BCM will control the wipers while in the WASH mode. The BCM will control either the front wiper relay or the rear wiper relay to turn on the wipers. The windshield wipers operate at low speed for 3 swipes and returns to the park position.

When turning on the washers do you hear the motor run ? Have some one try it while you listen at the washer fluid tank ! These pump motors do go bad .
turn OFF the ignition.
Disconnect the harness electrical connector of the windshield washer fluid pump.
Connect a test lamp from the windshield washer pump control circuit to a good ground .
Turn ON the ignition, with the engine OFF.
Press the front washer switch.
Does the test lamp illuminate?
YES or NO !

Nov 18, 2016 | Saturn Cars & Trucks

2 Answers

My 2006 Ford Taurus wipers only work on high were have replaced the switch and motor still only works on high


Did you do any testing before you replaced anything? With key on, wipers on low speed, does the white wire, at wiper motor, have voltage? Use a test light or voltmeter. You could back-probe the connector. If there is proper voltage, I can't see how it could be anything but the motor, I know you said you replaced it.
If there is no voltage, have to check wiring circuit and back-track.
26288827-oqvdoyvuadfzmrpqkwdmhozd-4-0.jpg

Sep 22, 2016 | 2006 Ford Taurus

2 Answers

What would cause the windshield wipers on my recently purchased Jeep Patriot Sport work on every speed except the high speed. High speed doesn't work at all.


The intermittent switch has a bad contact in it for the high speed, i would say, most likely will have to replace it.

Sep 15, 2014 | 2008 Jeep Patriot Sport

1 Answer

Where is the wiper relay


A wiring diagram doesn't show a relay, just a 25 amp fuse in fuse panel under driver's side of dash. Intermittent working is usually from a loose or poor or corroded connection, or the switch is old and tired, or the motor is old and tired.
Here is one way to check, if you have a test light: when the wipers are not working with wiper switch on high, and key is on, pull off the connector to the wiper/washer motor module (in the engine bay, on the firewall) and check if the purple wire has power. If it does, you probably need to replace the module. Inside the module is a park relay switch (to return wipers to down position when turned off) and a circuit breaker between the motor and ground.
If the purple wire does not have power when key is on and wipers on high, the connection is lost between the switch and the module, or the switch may be malfunctioning. The switch has 5 wires, white wire from 25 amp fuse (power in to switch), a pink wire (for the washer motor), a purple wire (high speed wipers), a dark green wire (low speed wipers), and a gray wire (for the park relay switch inside the wiper/washer motor module). If you see a yellow wire also at the module, that is part of the low speed wiper circuit (the dark green wire) coming from the park relay switch and then to the motor.
Good luck. Post back if further questions, or need more help.

Jun 06, 2013 | 1983 Chevrolet Celebrity

1 Answer

Window washers just stopped working


Its liknked with other things not just the pump. I believe it works with the wipers so if they work its probably not the fues. I would check the wires for a broken or burnt one

Mar 11, 2010 | 1998 Dodge Caravan

1 Answer

Front windscreen wiper wont stop why its a mitsubishi lancer evo4 i was touching the windscreen washer pump which had ceased working wipers came on and wont stop have to take the fuse out to stop them


Most cars turn on the wipers when the washer pump is turned on. Look for a stuck switch or relay in the washer circuit. It seems that the wipers think that the washer is on.

Jul 03, 2009 | Mitsubishi Lancer Evolution Cars & Trucks

1 Answer

I have a 2000 328i and the wipers work when switched on (both low and high), but i cannot get the washer or intermittent features to work. I have water in the reservoir but i don't hear the pump come on. ...


Sounds like a defective multiswitch on the steering column that is used to turn on wipers, washer, intermittent, etc. If you were only having problems with the washer, I might suspect the washer motor. But the fact that you are also having problems with the intermittent feature, I would suspect the multiswitch. If you can get access to the washer motor, you can test it by putting 12V to the connector to see if the pump will come on. Are your turn signals activated with the same switch as the wipers?

May 06, 2009 | 1997 BMW 328

1 Answer

Delay wipers don't work.


Try making sure the connection is good.
If it is then you should try replacing the wiper switch.


Brandon Bird

Jan 25, 2009 | 1999 Jeep Cherokee

1 Answer

2000 Jeep Cherokee Sport, window washing does not work


the little pump inside the washer fluid reservoir is bad, replace it

Dec 27, 2008 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...