Question about Land Rover Discovery

1 Answer

The start motor starts but it doent turn over

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Land Rover Master
  • 22,246 Answers

Would need to hear it to know exactly but it could ba anything from a siezed engine to a faulty starter motor ,i could soon tell by the noise it makes as to what is wrong ,so turn engine on bottom pulley and if engine turns over ok then its the starter motor for whatever reason and the course of action is to change it

Posted on Mar 22, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a toyota tazz 1.3 2e engine,i rekitted the carb n now it doent want to idle.please help


Re-adjust the jet screw on carb turn all the way in then turn 11/4 turn then go from there in or out. Reset idle screw. Make sure all vacuum lines are all in right place.

Jun 11, 2016 | Toyota Cars & Trucks

1 Answer

I have a crown vic 1998 my car was driving fine i was going to go to the store my car didnt turn on i open my hood i try to turn it on all i hear was i think the starter but the crazy thing is the band...


So you think you could hear the starter spin but the "band" did not turn? I suppose you mean the serpentine belt did not turn. It is quite possible for the starter to spin but the bendix to fail to engage the flywheel. This can be caused by low battery charge, bad battery connections, or more commonly, a bad starter.

Jan 08, 2015 | 1998 Ford Crown Victoria

1 Answer

Engine,,light,,comes,on..after,,driving,,25,miles,,,


what/////////////// codes //// are ///you ////getting,,,,,,and on ,,,what

Oct 04, 2014 | Cars & Trucks

1 Answer

Oil light came on and car died right after. now when i try to start it it doent do anything


have you checked the oil level? the light most likely came on due to low oil, the car wont allow the motor to start in order to not cause any further damage to the motor. good place to start would be to make sure the oil is at recomended level, if you cant start the car after that try disconnecting the battery for 30 seconds or so to reset the car computer, hook battery back up and try again.

Oct 19, 2011 | 2004 Chevrolet Cavalier

1 Answer

Plumber no work at present need car fixed doent my self not a nut job started life as motor mechanic got jag 2.1 02 plate swaped all discs no problem cant get back pistons to go back i think the divice at...


easy mate ,another good man whos left the trade disgruntled ,you get covered in oil and grease and socially outcast because of it ,anyway get a G clamp and apply a slight pressure and with a nice pair of snap on water pump pliers wind the pistons in, better if assistant turns G clamp whilst you turn piston or buy the special tool that pushes and turns at the same time

Sep 03, 2010 | Jaguar X-Type Cars & Trucks

1 Answer

I repair the motor of my mazda mpv 2002 and it doent started


You need timimg marks, There are the internal marks for installing timing chain, you follow the marks on the crank and cam and line them up, for the Ignition timing you follow the marks on the crankshaft harmonic balance, and the marks on the timimg chain cover for top dead center ect..

Feb 07, 2010 | 2002 Mazda MPV

1 Answer

My 95 dodge 3.9 dakota stalls when put into gear Ithink my cranksensor is hitting flywheel


It could be hitting the flywheel but it sounds like you have a short in a wire possible the crank sensor . You really need to start the truck and reach behind the motor and start shaking and pulling on the wiring harness.The wires themselves to the sensor may be bad. if that doent work try starting in neutral the shift to drive, if it still happens remove the sensor and check for rub marks. If so shim sensor with small thin washers.

Jan 28, 2010 | 1993 Dodge Dakota

2 Answers

It cranks but doent start


ignitioin module inside the distributor.

Jun 27, 2009 | 1995 GMC Sierra C1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8572 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...