Question about 2002 Chevrolet Blazer

2 Answers

How do i align my distibuter - 2002 Chevrolet Blazer

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 86 Answers

Alighning or adjusting the distributer will affect the timing. On most chevy models there's a screw or bolt with a triangler plate at the base of the distributer just loosen this bolt and you can adjust it. You may have to remove the bolt and plate for the distributer to turn. You may want to make sure you have a distibuter first 2002 models may not have them, i would think for that year model they would have converted to coil packs.

Posted on Mar 22, 2011

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 90 Answers

Did you have it out and want to make sure you put it in right or do you just want to set the timing?
If you just want to set the timing, then you just loosen the bolt that goes through the slot on the distributor a bit then turn left or right to advance or ****** the timing till you set it right then just tighten the bolt but be sure not to move the distributor whilst tightening.
If you need to make sure you've put it in right after having it out then just let me know and i'll tell you how.

Posted on Mar 22, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No spark to plugs


spark plugs screw into the engine,,,the other end of that same sparkplug wire runs to a distibuter,,when the cover of the distibuter is removed,the coil lies within on older model cars

Jun 07, 2012 | Cars & Trucks

2 Answers

No spark from distibuter engine turns over but wont start changed coil and modual distibuter cap and router


Hello there:
You may want ro remove the crankshaft and camshaft sensor and use a multimeter and set it to the lowest ohms setting and then touch the two ends of the meter on the pins of the sensor you are testing and see what reading you have it should read 0 then have somebody wave their hand rapidly in front of it and you should read a fairly high reading if not it is faulty and should be replaced i had the same thing happen to mine and it was my camshaft sensor and the wiring was bad too so may want to check it really close ok
Best regards Mike

Oct 06, 2010 | 1990 Ford F150

1 Answer

How do you reset distibuter timing after rebuild


Get the firing order of the motor you are working on, get the direction of rotation of the distributor shaft, pull the plugs and valve covers.
Afetr you line up the timing marks on the front of the enginecrankshaft/timing plate to zero, make sure #1 cylinder piston is up top of ots stroke by putting a screw driver into the plug hole and feeling the piston top, should be at its top stroke,make sure the intake and exhaust valves are both closed on the same cylinder, next go to the distributor and align the rotor to face the # 1 segmant in the distributor cap, lock everything down and install all parts you left open for the test and start it up.

Jul 02, 2010 | 1978 Ford Granada

1 Answer

Does the distibuter have to come out to change the pickup unit?


you have remove dist from motor then push out roll pin retaining gear then remove shaft the pickup assembly then reinstall

Apr 09, 2009 | 1989 Jeep Wrangler

1 Answer

91 chevy caprice classic, engine hesitates,replaced sparks,Wires, distibuter cap, roter button,new EGR valve


Check your fuel filter and air filter. That is usually where your hesitation starts.

Mar 17, 2009 | 1991 Chevrolet Caprice

2 Answers

1988 mustang rough idle its fine nwhen its cold then when it warms up it gets erratic


check plugs .rotor arm .distibuter cap .or check for dirty fuel filter

Feb 24, 2009 | 1992 Ford Mustang

1 Answer

Neon stops running after 1/2 hour


P1490 - Low Speed Fan Control Relay Circuit. The actual relay is located in the Power Distibution Center (PDC; the fuse/relay box in the engine).

Jan 18, 2009 | 1997 Dodge Neon

1 Answer

Fuel Distibutor


So the vehicle is flooding on start up ,KE jet seldom fails I think your ignition system is not working properly.

Oct 25, 2008 | 1985 Mercedes-Benz 190

1 Answer

1991 s10 pickup


what size engine do you have in your s10 pickup?

Jun 25, 2008 | 1991 Chevrolet S-10

Not finding what you are looking for?
2002 Chevrolet Blazer Logo

140 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...