Question about 2004 Mazda 6

Open Question

Hi there, I have a 1995 mazda 121, are the front wheel bearings pressed ?, or are they s flat bearing?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 337 Answers

SOURCE: 1995 ford contour / passengerside wheel bearing

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800a8e08

Posted on Dec 07, 2008

Ad
  • 1 Answer

SOURCE: mazda rustler 160i wheel bearings

a had sabe problem in a same model about one year.
i replaced inner and outer cv joint

Posted on Dec 17, 2008

simontricket
  • 235 Answers

SOURCE: Isuzu Wizard 1998 Front Wheel Bearing Adjustment

Jack up the wheel ,take off the allen screws (no oil) then see a locking ring with 3 cross head screws which will be very tight. take them out turn the adjusting ring cockwise and spin the wheel till the play is gone then get the next set of holes in line so there is a tiny bit of load on the bearings and bolt it back up - job done .

Posted on Apr 21, 2009

michigan man
  • 3533 Answers

SOURCE: Rear wheel bearings on Hyundai Accent

no i do not believe they are press in there are held in by a seal try www.autozone.com to see if they have your car listed if they do you will be able to get a diagram showing you how they come a part.

Posted on Apr 24, 2009

  • 17 Answers

SOURCE: how do I replace the front wheel bearings on a Mazda 626 1998

The front bearings on a mazda 626 are sealed and you must remove the entire hub assembly to have a shop or dealer install the bearings. The hardest part is you need to remove the center axel nut and it is very tight and is called a stake nut. If you do not have a fairly good amout of skill at repairs, this is one job that is safest left to the pros. Just one missed step can create more damage than you could beleive.

Posted on May 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Video of how to replace rear wheel bearings of a Mazda 323, 1.3,sting,front wheel power


take the rear hub off
you will need a hydraulic press or a vice to push bearing out and then in.

Jul 09, 2016 | Mazda Cars & Trucks

1 Answer

What is a front right barring on a mazda mx6


You must be referring to the wheel bearing. The wheel bearings are pressed into the wheel hub. If they are bad, most people just replace the hub with new bearings already installed.

Mar 18, 2012 | 1993 Mazda MX-6

1 Answer

Mazda mpv 2006 repack wheel bearing


There is a little difference between the front and rear. The days of packing wheel bearing is almost over. The front bearing you have to pull the hub and change to bearing. The rear wheel you have to change out the hub bearing and all. The front is a sealed bearing and not serviceable. Please rate my answer so I am rewarded points for it.

Jan 29, 2012 | Mazda Cars & Trucks

1 Answer

I need a diagram of the front wheel bearing assembly. I need to know how to remove the right front wheel bearing and remove - reinstall the center "geared insert" in the bearing without damaging...


These are pressed in. You have to press the hub out first(center part), then there is a C clip that has to be removed to press the bearing out. If you don't have a 20 ton press take it to a shop. Costs about$30.00

Feb 13, 2011 | 1998 Mazda 626

1 Answer

How do i pull the hub off my 2002 mazda , on drivers side front


REMOVAL & INSTALLATION Except Miata FRONT
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Steering knuckle from the vehicle
    • Inner oil seal from the knuckle
  3. Using Mazda Hub Puller tools 49 G033 102, 49 G033 104 and 49 G033 105, pull the front wheel hub from the knuckle assembly.
  4. Remove or disconnect the following:
    • Bearing inner race from the front wheel hub
    • Retaining ring from within the knuckle
    • Front wheel bearing from the knuckle, using the hub puller tools
    • Brake dust shield
  5. Clean and inspect all parts but do not wash or clean the wheel bearing. The bearing must be replaced. To install:
  6. Using Mazda Press tools 49 G033 107 and 49 H026 103, install a new dust shield cover assembly to the knuckle.
  7. Using the press tools, press a new wheel bearing into the knuckle assembly.
  8. Install or connect the following:
    • Wheel bearing retaining ring
    • New oil seal using Installation tool 49 V001 795
    • Front wheel hub using the Mazda press tools
REAR
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section. NOTE: The wheel bearings are not serviceable. If the bearings are bad, a new hub/bearing assembly must be installed.
  2. Remove or disconnect the following:
    • Rear wheels Fig. 1: Exploded view of the rear wheel hub and bearing assembly (disc brake model shown, drum is similar) 7923mg87.gif

    • Brake drum, if equipped
    • Rear caliper and rotor assembly from the hub, if equipped
    • Hub dust cover
  3. Raise the staked portion of the hub retaining nut with a hammer and chisel.
  4. Remove or disconnect the following:
    • Hub retaining nut and discard it
    • Hub and bearing assembly from the spindle Fig. 2: When installing the new hub nut, be sure to stake it into the notch on the spindle 7923mg86.gif
    To install:
  5. Install or connect the following:
    • Bearing assembly on the spindle. Torque the new nut to 131-173 ft. lbs. (177-235 Nm)
    • Stake the nut into the groove in the spindle
    • Dust cover
    • Assemble the brakes
    • Rear wheel

Jan 01, 2011 | 2002 Mazda Protege

1 Answer

Mazda rustler 160i wheel bearings


a had sabe problem in a same model about one year.
i replaced inner and outer cv joint

Dec 03, 2008 | 1997 Mazda 626

Not finding what you are looking for?
2004 Mazda 6 Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8567 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...