Question about Ford Transit Connect

1 Answer

Reconed the injector pump and now wont start. have replaced the starter motor. it wi nds over and trys to start. have bleed injectors, has diesel to all injectors .

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 240 Answers

I think there's a leak on your injector..there problem commonly cause by broken O-rings.


these are the materials you need :

Materials Needed

  • Flare Nut Wrench
  • Splined Socket
  • Wrench Set
  • Socket Set
  • Tweezers
  • 10 O-rings
  • 10 Copper Seats
  • Carb Cleaner
Washing it the day before will give the engine plenty of time to dry. Everything needs to be degreased before you begin, so that you do not get any dirt or debris into the pump or delivery valves.
Read more: http://www.doityourself.com/stry/how-to-fix-a-leaking-injector-pump#ixzz1HIjiOUpF


Posted on Mar 22, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mahindra xuv not starting after ran out of diesel


You will have to bleed the fuel filters then open the bleed screw on the injection pump. Physically pump the arm on your fuel pump until fuel is present at the injection pump bleeder. Then snug the bleeder closed. Turn the engine over with the starter, while cracking the injector lines open at the injector fittings, one at a time until fuel is present. Once you have fuel, snug the fitting closed and it should run at this point. let the starter rest between bleeding injectors to avoid damaging the starter

May 29, 2017 | Mahindra Cars & Trucks

1 Answer

How do you bleed a diesel pump jeep Cherokee turbo diesel 3.1 5 cylinder 2001


we dont have this engine here, USA.
but i have the WG jeep book,
starting page 12 , chapter 14


FUEL INJECTION PUMP BLEEDING
(1) If the fuel injection pump has been replaced,
air should be bled at the overflow valve before
attempting to start engine.
(a) Loosen the overflow valve (Fig. 18) at the
rear of the injection pump.
(b) Place a towel below the valve.
WARNING: WHEN CRANKING THE ENGINE TO
BLEED AIR FROM THE INJECTION PUMP, THE
ENGINE MAY START. PLACE THE TRANSMISSION
IN NEUTRAL OR PARK AND SET PARKING BRAKE
BEFORE ENGAGING THE STARTER MOTOR.
CAUTION: Do not engage the starter motor for
more than 30 seconds at a time. Allow 2 minutes
between cranking intervals.
(2) Crank the engine for 30 seconds at a time to
allow air trapped in the injection pump to vent out
the fuel injector drain tubes. Continue this procedure
until the engine starts. Observe the previous WARNING
and CAUTION.
(3) Tighten overflow valve.
HIGH-PRESSURE FUEL LINE BLEEDING
WARNING: THE INJECTION PUMP SUPPLIES HIGH-
-PRESSURE FUEL OF APPROXIMATELY 45,000 KPA
(6,526 PSI) TO EACH INDIVIDUAL INJECTOR
THROUGH THE HIGH-PRESSURE LINES. FUEL
UNDER THIS AMOUNT OF PRESSURE CAN PENETRATE
THE SKIN AND CAUSE PERSONAL INJURY.
WEAR SAFETY GOGGLES AND ADEQUATE PROTECTIVE
CLOTHING AND AVOID CONTACT WITH
FUEL SPRAY WHEN BLEEDING HIGH-PRESSURE
FUEL LINES.
WARNING: DO NOT BLEED AIR FROM THE FUEL
SYSTEM OF A HOT ENGINE. DO NOT ALLOW FUEL
TO SPRAY ONTO THE EXHAUST MANIFOLD WHEN
BLEEDING AIR FROM THE FUEL SYSTEM.
Bleed air from one injector at time.
(1) Loosen the high-pressure fuel line fitting at
the injector (Fig. 19).
(2) Crank the engine until all air has been bled
from the line. Do not operate the starter motor
for longer than 30 seconds. Wait 2 minutes
between cranking intervals.
(3) Start the engine and bleed one injector at a
time until the engine runs smoothly.

end quote.
pump timing is on next page
or tank filter line priming before. above.

Mar 22, 2016 | Jeep Cars & Trucks

1 Answer

Bleed deisel fuel lines


On the top of each injector were the fuel goes in there is a nut that you turn anti clockwise about half a turn, this is called cracking the line. This can be done with the motor running (if it will) or as you are pumping the lifter pump if motor wont run. You should see diesel squirting from the top of the nut, when it looks like a good stream with out any bubbles tighten the nut back down. This is done to each injector, if you are doing this with the lifter pump just get some diesel to the injectors and then try to start motor as this is best done with the motor running as you get better pressure.

Feb 17, 2015 | Cars & Trucks

1 Answer

Nissan navara wont start


ND22 or D40 .turbo or not is not the issue .. has to be a diesel motor if you are bleeding the injectors ..do you know the pump is working and where is the fuel filter tank lines should be ok if it was running before the engine rebuild and make sure diesel is getting to the injectors at the right pressure . no resetting that I know of ... thinking on this a bit more

Sep 04, 2014 | Cars & Trucks

1 Answer

How to bleed injector pump on isuzu nkr pick up


These are self bleeding so if diesel is getting to the pump it won't need bleeding. If you still feel the need to bleed the system then loosen one injector pipe turn the engine until you see diesel coming tighten again it should fire up. If you have a good flow of diesel coming from the filter to the pump and diesel at the injector pipe then your pump pressure may be low. To check remove any injector reconnect the pipe to it with the injector end where you can see it. Turn the engine with the starter a few times the diesel should be making a mist. Wear eye protection for this test

May 28, 2014 | 1995 Isuzu Trooper

1 Answer

VW Passat 2lt TDi. Diesel Reconed Eng .replaced Injectors but doesnt want to start


When you open up the diesel injector lines (take injectors out) you let air into the system and the diesel cannot make its way past it. You have to bleed the lines by opening the injector lines at the injector by a half turn. (Always be careful with diesel injector systems, it is under enough force to shoot a stream right into and under your skin causing nasty results) Cover the injectors with a towel and turn the car over until diesel is leaking out of each line. (Keep away from injectors while turning it over!) After diesel is seen coming from injector lines, retighten injector lines and try starting.

Sep 13, 2013 | Cars & Trucks

1 Answer

My 2002 chev. diesel truck turns over but wont start, new filter


anytime you change the filter in a diesel you have to bleed the air out of the fuel system. The pump won't auto bleed the fuel system for you. every place in the fuel system that has a flare type connection needs to be bleed, start at the connection closest to the tank, loosen the connection and then crank the engine until you see diesel fuel drips from that connection. Tighten the connection while the engine is still cranking. Move to the next connection that is going toward the engine. Continue on in that manner toward the engine until you reach the injector pump/injector. Once you reach the injector pump be VERY aware that the fuel is at VERY high pressure. Do NOT put your body parts in the stream of high pressure diesel fuel. It could kill or injure you! Once you bleed all the way to the injector pump/ injector, the truck SHOULD start. Do not bleed after the injector pump because of the pressure involved, it is WAY too dangerous.

Good luck!

Dec 22, 2012 | 2002 Chevrolet Avalanche

1 Answer

Diesel 1989 F-250 set too long and will roll over


You may have to bleed the fuel system. There may be a very small air leak in the fuel supply line and after a long time idle, the fuel seeps bac into the tank, leaving an air lock in the pipe. When you go to start, this air makes its way into your injection pump & needs to be bled out before the engine will start. Begin from your fuel filter bleed valve, next the injection pump using the primer pump to transfer the fuel. Next loosen off the injector pipes and crank the engine over until fuel sprays form all the joints. Tighten injector pipes and start. It may run a bit rough for to begin with, but will soon even out. If it doesn't start, repeat bleeding of injectors.

Mar 13, 2010 | 1989 Ford F 250

3 Answers

Truck wont start after draining fuel filter?


You may have gotten air in the fuel lines. Diesels cant deal with this as well as gas engines should be a purge / bleeder valve on the fuel lines to eliminate the air. may cough and sputter for a while

Jan 24, 2009 | 1999 Dodge Ram

3 Answers

Ran out of diesel on a 2002 dodge ram 2500 cummins...need to know how to bleed the system


just bump the ignition without starting it let sit for 20 seconds oruntill you hear lift pump shut off then shut off ignition and repeat do it 2 or 3 times should start then cummins is a self priming system has been for years even in semi trucks

Aug 10, 2008 | 2001 Dodge Ram 2500 Truck

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...