Question about 1996 Chevrolet S-10 Pickup

3 Answers

You have to hold the clutch pedel in just the right place before it will start

Posted by on

Ad

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 8,841 Answers

Hi, get your head under the dash to look at how the pedal arm pushes against the switch. It should push it all the way in and then stop. If the stop is missing or the switch is not installed properly, make repairs. Otherwise, replace the switch. You can always bypass the switch by removing the connector and putting a big paperclip in the connector to connect the terminals. Thanks for using FixYa.

Posted on Mar 22, 2011

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Chevrolet Master
  • 2,050 Answers

There is a safety switch for that, attatched to the clutch arm, which may be out of adjustment, or going bad.

Posted on Mar 22, 2011

Ad

Pretty obvious

Adjust or replace clutch switch,if it
is tested, and found to be worn

Posted on Mar 22, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 96 sunfire was sitting a long time before i bought it. It drove fine the first 100 miles. i thought the clutch was going out bc i had to push the pedel to the floor so the gears would engadge. When i...


Your losing fluid somewhere, it is a hydraulic clutch so this means hydraulic fluid powers it. Bring to transmission shop for repair.

If you need further help, reach me via phone at https://www.6ya.com/expert/frankie_091f536560a54e12

Apr 25, 2014 | 1996 Pontiac Sunfire

1 Answer

How to purge slavce cylinder on jetta 2000


to bleed the slave cly. you need a lot of pactence, and a good working clutch master cyl. pump it up 5 times or until you feel presure in the pedel and hold, and open the bleeder , and repet many times until all the air is out and you have a good pedel.

Nov 26, 2012 | 2000 Volkswagen Jetta TDI

1 Answer

My hyundai sonata 1999 model cannot start but their is light in the dashboard what will i do to fix the problem


have you depressed the clutch pedel sonatas have an interlock that prevent starting until the clutch pedel is pressed in if this does not fix the problem and the battery is fully charged trace the wiring from the clutch pedel to confirm its not brocken

Nov 12, 2010 | 1999 Hyundai Sonata

1 Answer

Clutch keeps coming out


if you mean the clutch doesnt engage until the pedel is nearly all the way out (up) .. then there is an adjustment for that called "free pedel adjustment" .. its usually a 5 min job .. however if there is any clutch chatter or noise then you may need a new clutch plate ... a bigger job ... one way to burn up the clutch plate is to allow it to slip for a long time ... and thats what will happen if the free pedel adjustment isnt done soon ... if your problem is not that then maybe you can expain more ....

Apr 15, 2010 | 1991 Volkswagen Jetta

1 Answer

Clutch does not release


did you check your pedal freeplay check your adjustment you need to have not more thant 1 inch freeplay on the clutch pedal what it does is when you did not adjusted right it cannot release your release bearing also check your linkage aite..

Feb 23, 2009 | 2005 Ford Fusion

1 Answer

New clutch and car is still slipping


in some cases if the ther is not enough free play in the clutch pedel as the engine area heats up things will expand in this case the distance of freeplay in your clutch pedel. have your clutch pedel freeplay adjusted. Also it is recomeded NOT to resurface the flywheels on nissans It dose change the hight and the distance for where the fingers of the pressure plate and the release bearing flang contact

Feb 18, 2009 | 1997 Nissan Maxima

1 Answer

Clutch


it could be either, look at your master cylinder in engine bay and look for leaks, if you find none look inside the car up under the clutch pedel, check for fluid seeping around where the pedel arm goes thru firewall and possibly under carpet

May 30, 2008 | 1987 Toyota Supra

Not finding what you are looking for?
1996 Chevrolet S-10 Pickup Logo

178 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

80263 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...