Question about Mitsubishi Passenger

Open Question

Dynatron KE-CLR-10 keyless entry. Replaced battery in handset uanble to open or close lock.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 60 Answers

SOURCE: keyless entry won't work

Try changing the battery in your remote

Posted on Aug 11, 2008

Ad
  • 4 Answers

SOURCE: keyless remote does not work after replacing batteries

I had the same problem and located the addendum to the owners manual. It's kind of overcomplicated it seems. Here is what it says:
1) Confirm all doors are closed and the key is out of the ignition.
2) Open the driver's door and put the key in the ignition within 10 seconds.
3) Remove the key within 10 seconds.
4) Push and release the driver's door switch 3 times within 20 seconds.
5) Insert the ingition key within 10 seconds.
6) remove the ignition key within 10 seconds
7) press and hold both "lock" and "unlock" on the transmitter for more than 5 seconds within 20 seconds of removing the key All doors will lock/unlock to confirm the process has been properly done.
8) Press "lock" or "unlock" on the transmitter within 5 seconds of completing step 7. All the doors will lock/unlock to confirm that the process was properly done.
At this point the transmitter has been properly programmed.

Of course, this didn't help me. My transmitter still does not work. I did confirm the procedure with a known good transmitter, so it is valid. If the lock/unlock does not happen in step 7, you more than likely have a bad transmitter.

Posted on Nov 30, 2008

  • 5 Answers

SOURCE: keyless entry won't work

I have a 1999 BMW E46 I have had a problem with the keyless entry myself. I brought the car to BMW Dealer and they told me that my Lock had an issue and that they need to repair some wiring wich would cost me $1,023.98 to find out that it was a fuse that burned out. I have replaced the 5 amp fuse with another one but it burned the fuse again so I put a 10 amp fuse and i have not had a problems since. In my car is fuse # 54 if Im not mistaken. But waht you can do is open the fuse box which is located in your glove compartment look for a diagram that shows you which fuse is where it will give you a fuse name a number where the fuse is located and how many amps fuse it is.

Posted on Dec 23, 2008

  • 27 Answers

SOURCE: How do i program remote keyless entry?

You don't normally program a keyless entry, that's done for you by the technicians that install that. If the replaced battery doesn't solve the problem, take the battery and the remote to the techies that installed it.

Posted on Mar 28, 2009

goalie39
  • 469 Answers

SOURCE: keyless entry code for 2003 lincoln aviator

Every car different, call an auto rescue or towing company, the trucks are usually equiped with slim jims, that can be used to gain access to your vehicle.

Hope this helps.
Ed

Posted on May 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My interior light won't come on in my 1999 Buick Lesabre. I have checked the bulb & the fuse. Can anyone help me with this problem? Any ideas are sincerely appreciated.


Courtesy Lights
The courtesy lights come on under the following conditions:
?€¢
Any door is opened.


?€¢
The interior lamp switch is in the ON position.


?€¢
The keyless entry transmitter unlocks the doors (illuminated entry).

When the key is removed from the ignition switch with all of the doors closed, the courtesy lights light for approximately 25 seconds before fading out.
Battery positive voltage (B+) is applied at all times through the IP fuse block CTSY LP/PWR MIR fuse 6A via CKT 640 (ORN) through the body control module (MALL) to the courtesy lights via CKT 1732 (ORN). The MALL provides a ground through CKT 156 (WHT) for the courtesy lights under the following conditions:
?€¢
The MALL receives an input from a door being opened.


?€¢
The MALL receives an input from the interior lamp being turned ON.


?€¢
The MALL receives an input from the doors being unlocked using the keyless entry transmitter.

The courtesy lamps then light.
When the courtesy lights are activated by opening and closing a door, the courtesy lights will remain on for approximately 25 seconds before fading out after all of the doors are closed. If the ignition switch is turned to START or RUN within the 25 seconds, the lights immediately begin to fade out. If a door is left open, the MALL removes battery positive voltage (B+) to the courtesy lights after 10 minutes. When the courtesy lights are activated by the interior lamp switch, the lights remain on as long as the interior lamp switch is in the ON position. When the courtesy lights are activated by unlocking the doors using the keyless entry transmitter, the lights remain on for approximately 40 seconds. If the doors are locked using the keyless entry transmitter within the 40 seconds, the lights immediately begin to fade out.
Body Control Module (MALL) Diagnostic Mode
For a detailed explanation of the MALL module diagnostic mode, refer to Body Control Module Cell 51.
What interior light ? Dome , courtesy lights etc....They don't work with switch, keyless entry , door opening ?
What

Dec 03, 2015 | Buick Cars & Trucks

1 Answer

2004 Suzuki Gran Vitara Keyless entry


Try this

2004 XL7

1. Remove key from ignition switch.

2. Close all doors.

3. Open drivers door

4. Insert key and turn to ON position and within 10 seconds turn
key off and remove key.

5. Within 20 seconds Close and open drivers door 3 times.

6. Insert key and turn to ON position and within 10 seconds turn
key off and remove key.

7. Locks should now lock and unlock automatically to confirm you
have entered programming mode.

8. Press the UNLOCK button on remote and locks should cycle to
confirm programming.

9. Repeat step 8 on each additional remote.

10. Exit vehicle with keys and remote, close door test remote(s)

Jun 01, 2014 | 2007 Suzuki XL-7

1 Answer

Keyless entry remote will not unlock doors for charger 2010


did you change the battery in the transmitter? if so, you have to stand close to the vehicle and hold down the lock and unlock buttons for about 10 seconds. if you replaced a transmitter, it has to be programmed to the vehicle at the dealership. hope that helps, ken

Jan 22, 2013 | Dodge Cars & Trucks

4 Answers

2003 330XI keyless entry. wont open or close.


The transponder is not effective any longer sometimes the battery of the remote is very low which needs to be replaced

Jan 17, 2018 | BMW 330xi Cars & Trucks

1 Answer

2000 Lincoln Towncar. Keypad on door will not unlock doors. Interior lights do come on. The last two keys pushed simultaneously will occasionally lock the doors. I am using the code printed on a sticker in...


The driver door module (DDM) is connected on the standard corporate protocol (SCP) communication network. The DDM controls many functions including power windows, power door locks and remote keyless entry. The DDM also communicates with the driver seat module (DSM) to control the power mirror and seat memory functions.
Do you know anything about automotive electronic control modules ?
The driver door module (DDM) receives inputs from the digital transmission range (DTR) sensor, ignition switch, seat switch, window/door lock switches, lighting control module (LCM), keyless entry keypad switch and remote transmitter. The DDM outputs consists of keyless entry keypad switch illumination, power door lock actuators, luggage compartment release solenoid, horn relay, and lighting control module (LCM).
Best thing to do would be to have a factory scan tool hooked up to check for DTC'S diagnostic trouble codes . That should be the first step if it's not programming the code.
  • The doors do not lock/unlock using the keyless entry keypad
  • Keypad.
  • Circuitry.
  • Driver door module (DDM).
  • GO to Pinpoint Test L .

PINPOINT TEST L: THE DOORS DO NOT LOCK/UNLOCK USING THE KEYLESS ENTRY KEYPAD CONDITIONS DETAILS/RESULTS/ACTIONS L1 RETRIEVE THE RECORDED RESULTS FROM BOTH CONTINUOUS AND ON DEMAND SELF TESTS Use the recorded DDM DTCs from the Continuous and On Demand self tests.
  • Are any DTCs recorded?
Yes For DTC B1525, GO to L3 .

For all other DDM DTCs, REFER to the DDM Diagnostic Trouble Code (DTC) Index.

No If the door locks are inoperative, GO to L2 .

If the keypad illumination does not operate, GO to L10 .

If the keypad illumination is on continuously, GO to L14 .
L2 CHECK THE DOOR LOCK OPERATION Check the door lock operation by depressing a door lock switch.
  • Do the door locks operate?
Yes GO to L3 .

No GO to Pinpoint Test E . L3 MONITOR THE DDM PID KEY_PAD
Scan tool
Monitor the DDM PID KEY_PAD.
  • Are any of the keyless entry keypad switch numbers present?
Yes GO to L4 .

No GO to L5 . L4 CHECK THE KEYLESS ENTRY KEYPAD SWITCH
Keyless Entry Keypad Switch C525
Monitor the DDM PID KEY_PAD.
  • Are any of the keyless entry keypad switch numbers present?
Yes If 1/2, REPAIR Circuit 78 (LB/YE). TEST the system for normal operation.
If 3/4, REPAIR Circuit 79 (LG/RD). TEST the system for normal operation.
If 5/6, REPAIR Circuit 121 (YE/BK). TEST the system for normal operation.
If 7/8, REPAIR Circuit 122 (YE). TEST the system for normal operation.
If 9/0, REPAIR Circuit 123 (RD). TEST the system for normal operation.

No INSTALL a new keyless entry keypad switch; for additional information, REFER to Keypad-Keyless Entry . L5 CHECK THE KEYLESS ENTRY KEYPAD INPUT WITH THE KEYLESS ENTRY KEYPAD SWITCH Monitor the DDM PID KEY_PAD, while depressing all the keyless entry keypad switches one at a time.
  • Are all the keyless entry keypad switches operating correctly?
Yes GO to L9 .

No GO to L6 . L6 CHECK CIRCUIT 797 (LG/VT) FOR VOLTAGE
Keyless Entry Keypad C525
Measure the voltage between keyless entry keypad C525-7, Circuit 797 (LG/VT), and ground; and between keyless entry keypad C525-8, Circuit 797 (LG/VT), and ground.
  • Are the voltages greater than 10 volts?
Yes GO to L7 .

No REPAIR Circuit 797 (LG/VT). TEST the system for normal operation. L7 CHECK THE KEYLESS ENTRY KEYPAD SWITCH INPUT While monitoring the DDM PID KEY_PAD, momentarily connect a fused (7.5A) jumper wire between positive battery post and keyless entry keypad switch C525 as follows:
    Keypad Button Keyless Keypad Switch C525 Circuit 1/2 Pin 3 78 (LB/YE) 3/4 Pin 4 79 (LG/RD) 5/6 Pin 5 121 (YE/BK) 7/8 Pin 6 122 (YE) 9/0 Pin 1 123 (RD)

  • Are all the keyless entry keypad switch inputs operating correctly?
Yes INSTALL a new keyless entry keypad switch; for additional information, REFER to Keypad-Keyless Entry .

No GO to L8 . L8 CHECK THE KEYLESS ENTRY KEYPAD SWITCH CIRCUITRY FOR AN OPEN
DDM
Measure the resistance between keyless entry keypad switch C525 and DDM as follows:
    Keyless Keypad Switch C525 DDM Circuit Pin 3 C521 Pin 8 78 (LB/YE) Pin 4 C521 Pin 13 79 (LG/RD) Pin 5 C521 Pin 16 121 (YE/BK) Pin 6 C520 Pin 24 122 (YE) Pin 1 C520 Pin 25 123 (RD)

  • Is the resistance less than 5 ohms?
Yes INSTALL a new DDM; for additional information, REFER to Section 419-10 . TEST the system for normal operation.

No REPAIR the circuit in question. TEST the system for normal operation. L9 CHECK THE KEYLESS ENTRY KEYPAD BACKLIGHT Depress a key on the keyless entry keypad.
  • Does the keypad illumination operate correctly?
Yes INSTALL a new DDM. For additional information, REFER to Section 419-10 . TEST the system for normal operation.

No If the keypad illumination does not operate, GO to L10 .

If the keypad illumination is on continuously, GO to L14 . L10 CHECK THE KEYPAD - DDM ACTIVE COMMAND KEYPAD BACKLIGHTING LIGHT ON AND OFF Trigger the DDM active command KEYPAD BACKLIGHTING LIGHT ON and OFF.
  • Does the keypad illumination turn off and on?
Yes INSTALL a new DDM. For additional information, REFER to Section 419-10 . TEST the system for normal operation.

No GO to L11 . L11 CHECK DDM GROUND - JUMPER CIRCUIT 66 (LB) TO GROUND
DDM 522
Connect a fused (7.5A) jumper wire between DDM C522-4, circuit 66 (LB), and ground.
  • Does the keypad illuminate?
Yes INSTALL a new DDM; for additional information, REFER to Section 419-10 . TEST the system for normal operation.

No GO to L12 . L12 CHECK CIRCUIT 51 (BK/W) FOR OPEN
Keyless Entry Keypad C525
Measure the voltage between keyless entry keypad C525-7, circuit 797 (LG/VT), and ground; and between keyless entry keypad C525-8, circuit 797 (LG/VT), and ground.
  • Are the voltages greater than 10 volts?
Yes GO to L13 .

No REPAIR circuit 797 (LG/VT). TEST the system for normal operation. L13 CHECK CIRCUIT 66 (LB) FOR OPEN Measure the resistance between keyless entry keypad C525-2, Circuit 66 (LB), and DDM C522-4, Circuit 66, (LB).
  • Is the resistance less than 5 ohms?
Yes INSTALL a new keyless entry keypad switch; for additional information, REFER to Keypad-Keyless Entry .

No REPAIR Circuit 66 (LB). TEST the system for normal operation. L14 CHECK THE KEYPAD ILLUMINATION - DDM DISCONNECTED
DDM C522

  • Does the keypad illumination turn off?
Yes INSTALL a new DDM; for additional information, REFER to Section 419-10 . TEST the system for normal operation.

No GO to L15 . L15 CHECK KEYLESS ENTRY KEYPAD FOR SHORT TO GROUND
Keyless Entry Keypad C525

  • Does the keypad illumination turn off?
Yes GO to L16 .

No INSTALL a new keyless entry keypad switch. For additional information, REFER to Keypad-Keyless Entry . TEST the system for normal operation. L16 CHECK CIRCUIT 66 (LB) FOR SHORT TO GROUND Measure resistance between DDM C522-4, circuit 66 (LB), and ground.
  • Is resistance greater than 10,000 ohms?
Yes System OK. CLARIFY the concern with the customer.

No REPAIR circuit 66 (LB). TEST the system for normal operation.

Nov 03, 2017 | Lincoln Town Car Cars & Trucks

1 Answer

Keyless entry on honda civic 2006 not working


The keyless entry is designed to work with the doors closed (closed - not locked). If the door ajar sensor thinks the door is open the keyless entry is disabled. When you manually lock the door it might tighten the door just enough to activate the keyless entry. I would try slamming all the doors closed and then see if the keyless entry works. If it still wont work have the wiring checked on the front door lock.

May 12, 2009 | 2006 Honda Civic Hybrid

1 Answer

Keyless FOB not opening locks


You may have to car to Chevy Dealership to reprogram keyless entry.

Apr 27, 2009 | 1998 Chevrolet Monte Carlo

4 Answers

Keyless entry won't work


you need to reprogram your remotcontrol by doing this
1, turne the ignation on and trun it off
2, prassed and hold the unlock botten and prasse 3 time the open botton
3, relesed all botten then the door well open and closed normal

Aug 11, 2008 | 1999 BMW 323 Series

5 Answers

Mazda MPV 2000


Try "resetting" your keyless entry code. Which is a fancy way of explaining that I broke my keyless entry key fob and had to order a new one. It came w/ instructions explaining how to get the new fob to speak to the car's computer. It was weird (turn key on and off 3 times, open and close door three times, etc. **I'm sure my neighbors were watching and laughing**), but it worked. I'll scan and email you the insrtuctions if you wish. Dan: dcarterlaw@lycos.com

Jul 07, 2008 | 2000 Mazda MPV

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...