Question about 2004 Hyundai Santa Fe

Open Question

Where is the alarm sytem control module located and how do i program new remote transmitters on a 2004 hyundai santa fe. is there a picture of what the contrl module looks like.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6 Answers

SOURCE: how to change spark plugs on hyundai 2004 2.4L

Remove the plastic cover that goes over the engine (the one with the Hyundai logo).
At this point, you will see the cables that goe to each fo the spark plugs.
Noting their position, remove them.
The spark plugs are ready to be removed, turn counterclockwise and replace with manufacturer recomended ones.

Posted on May 16, 2009

  • 1 Answer

SOURCE: how to program 2004 Hyundai Santa Fe Keyless Entry

I have a 2002 Hyundai Santa Fe and just completed adding keyless remore. The control module is the large black box behind and below the fuse box next to the hood release. 'Set' and 'off' are written small and in yellow on the side of the box closest to the steering column, and were obscured by wires coming out of the fuse box. There was a sticker over the switch that had to be pierced to get to the small switch. I used a small pick to move the switch as it is difficult to get your fingers in there. Turned ignition switch two clicks to 'Acc' location and waited 5 seconds; some instructions I found said move to 'on' location but didn't work for me; then moved switch to 'set'; pushed remote lock button; set switch to 'off'; turned off ignition and tested. Most difficult part was finding switch.

Posted on Dec 29, 2010

goalie39
  • 469 Answers

SOURCE: ''check engine light'' illuminated, 1004 Hyundai, Santa Fe

If you live in the US, take it to qany Auto Zone store and thy will read the codes off for you, I would suspect any right thinking competitor would do the same, check if you don't have one near by.

Hope this is of some help.
Ed

Posted on Apr 21, 2009

emissionwiz
  • 75744 Answers

SOURCE: PROGRAM KEYFOB FOR HYUNDAI SANTA FE

This is from the factory service manual of your car:
There is no onboard programming procedure for this vehicle. This vehicle requires special equipment be connected to the vehicle to program the keyless remote. Translation you need the dealer to do this.

Posted on May 22, 2009

  • 84 Answers

SOURCE: Change serpentine belt 2004 Hyundai Santa Fe

it uses a spring loaded tensioner.use a breaker bar to rotate the tension and it should just come off.if u need a pic or anything else to do it let me know,

Posted on Oct 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

4x4 diesel. Why can't doors be unlocked or locked?


their is a way to do it but recheck battery first sometimes the relearn process doesnt work or the fob itself is dead also if auto /remote start will need dealer to flash fob ---- 2002 santa fe and followed programming instructions and eventually was able to program the new remote. But, I did not realize I had to program my existing remote at the same time. Since, I have retried programming both remotes many times with no success--the new one works, but the old one won't. The instructions were: 1) Locate switch under dash, behind fuse box; 2) Turn ignition switch on, but don't start engine; 3) Wait 5 seconds, set memory switch to SET position; 4) Press remote LOCK button; press second remote transmitter LOCK button; 5) Set memory switch to OFF; 6) Switch ignition OFF. 7) Confirm programming by locking and unlocking vehicle.
Remote Key Programming Hyundai Forums Hyundai Forum

Sep 23, 2015 | 2003 Hyundai Santa Fe

1 Answer

How do I replace a power train control module on a 2004 Hyundai Santa fe


I don't know how you have concluded the PCM is the problem here. You're probably jumping t conclusions without sufficient testing but the new PCM has to be programmed in the car before the engine will run.
It's located in front of the console, under the HVAC housing.



25350780-kiyu5aqkqelb2o03f4kwguli-3-0.jpg

Jan 02, 2015 | 2004 Hyundai Santa Fe

1 Answer

I need instructions to program keyless entry remote for 2002 Hundai Santa Fe


For a 1994 to 2006 Sonata, a 2001 to 2006 Elantra, a 2000 to 2006 XG350 or a 2001 to 2006 Santa Fe, you will need to access alarm system control module. On most of those vehicles it is located on the driver's side fascia panel. But on the Sonata, the facia panel is in the center.

  • 2 Once you have found this module, you will want to ensure that the memory switch is in the OFF position. Then turn the ignition on.
  • 3 Wait 5 seconds and set the memory switch to SET position and then press the remote transmitter lock button to send the code to the alarm system control module.
  • 4 If you would like to program a second remote transmitter then you will need to press second remote transmitter lock button.
  • 5 Next set the memory switch to off, then turn the ignition off. You can confirm your programming by locking and unlocking the vehicle with both of the remotes. good luck my friend
  • Feb 08, 2012 | Hyundai Cars & Trucks

    1 Answer

    Just bought a 2004 hyundai Santa Fe. Trying to learn how to set the alarm. Can someone help me please?


    PRESS THE REMOTE TRANSMITTER UNLOCK BUTTON ONE TIME DEACTIVATES ALARM AND UNLOCKS THE DRIVERS DOOR ONLY. PRESSING THE REMOTE TRANSMITTER TWICE DEACTIVATES ALARM AND UNLOCKS ALL DOORS.

    Feb 01, 2011 | 2004 Hyundai Santa Fe

    2 Answers

    Hyundai santa fe key fob 1 works 1 does not have changed battery deal says to buy new ,can i unlock with key without alarm going off


    System operation
    Pressing remote control lock button locks vehicle and activates system Fig. 1 . Indicators flash once. Pressing remote control unlock button unlocks vehicle and deactivates system Fig. 1 . Indicators flash twice.
    Fig. 1
    Synchronization
    When
    System malfunction. Remote control added or replaced.
    How
    Access alarm system control module located under driver's side lower fascia Fig. 2 . Set memory switch to SET position. Press remote control lock or unlock button. Set memory switch to OFF position. Confirm synchronization has been successful by locking and unlocking vehicle. Repeat procedure for second remote control. Synchronization can also be carried out using diagnostic equipment.
    NOTE: A maximum of 2 remote controls can be programmed. NOTE: If remote control fails, system can be deactivated as detailed in the owner's handbook.

    Jul 30, 2010 | 2003 Hyundai Santa Fe

    1 Answer

    Exactly where is the alarm system control module on a 2004 Santa Fe


    If I dont remember bad, access to alarm system control module located under driver's side lower fascia.

    Hope this help.

    Mar 31, 2010 | Hyundai Motor 2004 Sonata

    3 Answers

    How to program 2004 Hyundai Santa Fe Keyless Entry Remote


    Synchronization
    When
    System malfunction. Remote control added or replaced.
    How
    Access alarm system control module located under driver's side lower fascia Fig. 2 . Set memory switch to SET position. Press remote control lock or unlock button. Set memory switch to OFF position. Confirm synchronization has been successful by locking and unlocking vehicle. Repeat procedure for second remote control. Synchronization can also be carried out using diagnostic equipment.
    NOTE: A maximum of 2 remote controls can be programmed. NOTE: If remote control fails, system can be deactivated as detailed in the owner's handbook.

    Mar 23, 2010 | 2004 Hyundai Santa Fe

    2 Answers

    Program factory remote keyless entry: 2003 Hyundai XG350


    The procedures you list require the Hyundai Keyless Remote programming module, which you don't have. This module is proprietary - only Hyundai Dealerships have it. There is a 10 pin connector under the dash (next to the DLC - Data Link Connector) which is used to connect the Keyless Remote Programming Module. This module has two switch positions "Ready" and "SAVE". When the switch is place in the 'SAVE" position, that's when the keyless remotes are activated to send their 'codes' to the Electronic Time and Control System (ETACS). The module's switch is then set to "Ready" and the remote is tested to see if it works properly.

    May 22, 2009 | Hyundai Motor 2003 XG350

    1 Answer

    Program factory remote keyless entry for 2003 Hyundai XG350


    This bulletin supersedes TSB# 02-90-001.
    DESCRIPTION: The security system keyless adapter cable (SPX/Kent-Moore P/N 09900-21300) is a special service tool (SST) that is used for programming new keyless entry remote transmitters to the factory security systems. The keyless adapter is used in conjunction with the Hi-Scan Pro (with Hi-Scan SOL Pro Software Version 09-29-03
    or newer) and Data Link Connector (DLC) Cable. SERVICE INFORMATION: The keyless adapter cable can be used on the following vehicles:
    • 2001 - 2004 MY Elantra
    • 2001 - 2004 MY Santa Fe
    • 2002 - 2004 MY Sonata
    • 2001 - 2004 MY XG300/350 0390020a.gif
    NOTE
    • The 2003 - 2004 MY Tiburon does not need the Keyless Adapter Cable to add keyless entry remotes to the factory security system. Instead, the Hi-Scan Pro connects to the vehicle using only the DLC cable. See page BE-60 in the 2004 MY Tiburon Shop Manual for the latest instructions.
    • The most current Keyless Adapter Cable Instructions are available in the following shop manuals:
    SHOP MANUAL

    PAGES

    2004 MY Elantra
    BE-73 - BE-74
    2004 MY Santa Fe
    BE-43 - BE-44
    2004 MY Sonata
    BE-40 - BE-41
    2004 MY XG350
    BE-46 - BE-47
    KEYLESS ADAPTER CABLE INSTRUCTIONS:
    1. Connect the keyless adapter cable to the Hi-Scan Pro DLC cable. 0390020b.gif
    2. Plug the keyless adapter into the vehicle's 10-pin multi-purpose connector located behind the driver's side lower instrument panel (next to the DLC). NOTE Sample vehicle shown is the Santa Fe.
      0390020c.gif
    3. Turn the Hi-Scan Pro ON
      and press ENTER
      . NOTE "Release date 29. Sep. 2003" OR LATER
      must appear on this screen. To update your SOL card with the latest software go to www.hmaservice.com and refer to TSB 00-00-001.
      0390020d.gif
    4. Select option "HYUNDAI VEHICLE DIAGNOSIS"
      and press ENTER
      . 0390020e.gif
    5. Select vehicle model and press ENTER
      . 0390020f.gif
    6. Select option "TRANSMITTER CODE SAVING"
      and press ENTER
      . 0390020g.gif
    7. Ensure that the key has been removed from the ignition cylinder before proceeding. 0390020h.gif
    8. Follow the steps noted on the Hi-Scan Pro screen to program the remote(s). NOTE The factory security system can only be programmed to accept two remote transmitters and MUST be programmed for both remote transmitters at the same time.
      0390020i.gif
    9. Press ESC
      on the Hi-Scan Pro and verify that the remote(s) are functioning properly.
    10. Turn the Hi-Scan Pro OFF
      and disconnect the adapter cable from the multi-purpose connector.

    May 22, 2009 | Hyundai Motor 2003 XG350

    1 Answer

    2004 Hyundai Santa Fe Reprogramming Remote Entry Fob


    Remote control added or replaced.
    How
    Access alarm system control module located under driver's side lower fascia behind fuse box, should see it without removing any parts. Fig. 2 . Set memory switch to SET position using a very small screwdriver. Press remote control lock or unlock button. Set memory switch to OFF position. Fob won't move locks until you put it in the off position. Confirm synchronization has been successful by locking and unlocking vehicleicon1.png. Repeat procedure for second remote control or in my case I did them at the same time and they both work fine. Synchronization can also be carried out using diagnostic equipment.
    NOTE: A maximum of 2 remote controls can be programmed. NOTE: If remote control fails, system can be deactivated as detailed in the owner's handbook.

    Mar 18, 2009 | 2004 Hyundai Santa Fe

    Not finding what you are looking for?
    2004 Hyundai Santa Fe Logo

    Related Topics:

    961 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Hyundai Experts

    yadayada
    yadayada

    Level 3 Expert

    75744 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8123 Answers

    Are you a Hyundai Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...