Question about 1992 Dodge Caravan
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
3.3 engines has the egr valve with transducer.you have to replace the whole unit. code p0406 what its trying to tell you your egr valve circuit is short to ground.it has failed .
Posted on Jul 04, 2009
11- no start since battery disconnected.
12- battery has been disconnected recently.
22-Coolant temperature sensor, bad connection or faulty.
44-signal to smec (engine computer) was interrupted, or is not present.
55- is end of codes.
What exactly are you experiencing as far as starting and driving goes.
The only code I see right now that I would worry about is the coolant temperature sensor, if you are experiencing poor running, starting etc.
The signal to smec, may have been a one time thing, if vehicle runs.
Posted on Feb 02, 2010
Click on the following free direct Link.
It has the correct Belt Diagrams for your 1992 Dodge Grand Caravan wirh either the 3.0L SOHC V6 or the 3.3L V6.
Included on the Diagrams are the Instructions on "Rotating" the Automatic Tensioner. See Below for additional Instructions to make your job easier.
"HOW TO": I professionally prefer the Serpentine Tensioner Tool.
Standard Rules to Removal the Serpentine Belt with an Automatic Tensioner:
1. Find the Tensioner(s).
2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (located on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening located on the Tensioner Arm) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
3. Remove the loosened belt off one of the other more easily accessed Pulleys.
4. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.
Standard Rules for Installing the Serpentine Belt with an Automatic Tensioner:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them.
Before You GO:
Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!
Posted on Apr 12, 2010
Tips for a great answer:
Dec 05, 2015 | 2005 Dodge Grand Caravan
Oct 14, 2014 | 2005 Dodge Grand Caravan
Aug 17, 2014 | 2000 Dodge Grand Caravan
Aug 09, 2012 | 1999 Dodge Grand Caravan
Jun 09, 2011 | 2006 Dodge Grand Caravan
Jan 12, 2011 | 2003 Dodge Grand Caravan AWD
Dec 28, 2009 | 2006 Dodge Grand Caravan
Oct 13, 2009 | 2003 Dodge Grand Caravan AWD
129 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: